← 050 · 051 · 075 · 076

Stihl 1111 · Section H · 8 of 14 · 41 parts

Filter housing, Air filter

Fits 050, 051.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232425262728292933031323334353637456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (41)

PosPart numberDescriptionQty
1 1111 129 1400 Gasket 0.5 mm 1
2 1111 146 7400 Deflecting plate 1
3 1111 129 1400 Gasket 0.5 mm 1
4 1111 120 2203 Flange 1
5 9022 341 1070 Spline screw IS-M5x30 2
6 9121 319 1120 Stud M5x55 2
7 1111 129 1100 Gasket 1
8 1111 120 0608 Carburetor WJ-112 1
8 1111 120 0601 Carburetor HS-60D 1
9 1110 149 1200 Gasket 1
10 1111 140 2801 Filter housing 1
11 1115 121 7700 Guide piece 1
12 1111 185 2001 Choke lever 1
13 0000 997 0326 Compression spring 1
14 9516 003 1730 Ball Ø 4 mm 1
15 0000 951 2600 Oval head screw M4x10 1
16 9121 347 1080 Stud M5x35 1
17 1110 122 6201 Idle speed adjustment screw 1
18 9216 261 0700 Hexagon nut M5 2
19 1111 148 4000 Strap 1
20 9022 341 1010 Spline screw IS-M5x18 1
21 1111 182 1501 Throttle rod 1
22 1111 185 1900 Choke rod 1
23 1111 149 1200 Gasket 1
24 1111 120 1601 Air filter, fleece Fitment / change note → 1
24 1111 120 1602 NLA Air filter, wire mesh option 1
25 1111 141 0504 Filter cover 1
26 1111 967 1508 Model plate 051 1
27 0000 967 1530 Model plate 051 AVE 1
28 1111 967 1500 Model plate 051 AVEQ 1
29 0000 974 1000 Round head rivet 3x6 2
30 0000 958 1705 Washer 1
31 1110 140 9501 Twist lock 1
32 9455 621 1670 Circlip 16x1 1
33 1111 430 0202 Stop switch 1
34 9211 260 1430 Hexagon nut M12x0.75 1
35 1110 432 9200 Grommet 1
36 not sold separately Hose 3.1x5.7x120 mm, R3 not available as a separate item 1
37 0000 997 0626 Helical spring 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2803 Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption 1
— 1111 007 1052 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 051 / 076

051 / 076: fleece filter under unchanged numbers

Fleece replaces flocked wire cloth; old stock, cleaning direction and replacement limits remain distinct.

  • TI38/1996 replaces flocked wire cloth with fleece under UNCHANGED replacement-part numbers. Introduction is IN PROGRESS, without a serial cutoff. Remark 1 says the unmodified version is supplied until existing stocks are exhausted. A number alone therefore does not identify the material of an old-stock filter; this is a historical supply statement, not a current stock guarantee.
  • The 051/076 row prints 1111 120 1601 with remarks 1 AND 2. Remark 2 literally says SEE TI31.95. This is a retained SOURCE REFERENCE MISMATCH: retained TI31/1995 concerns 024/026, not 051/076. Do not silently replace the citation, transfer 026 compensator conditions, or invent an intended bulletin. Its intended meaning remains unknown.
  • The same part appears in the later 075 sheet and a combined 050/051 sheet. TI38 names only 051 and 076 here: no 050 or 075 fitment is added, and the combined catalog label does not broaden the source assertion. The prior-TI footer lists TI40/1992 for 076 only, not a replacement for remark 2.
  • The source calls fleece especially suitable for dry and dusty conditions. Its rougher surface may look heavily contaminated when only lightly loaded; appearance alone does not establish loading. Clean DAILY OR when there is a noticeable loss of power during cutting. The observation about appearance does not cancel that interval.
  • If possible, carefully blow out at LOW PRESSURE from the CLEAN AIR SIDE. For stubborn dirt or caked fleece, wash in a clean, NON-FLAMMABLE solution, for example warm soapy water. DO NOT CLEAN WITH A BRUSH: it forces dirt into the fleece. No pressure value, drying time or alternate solvent is specified.
  • The source attributes improved filtering efficiency to the material structure, not a measured result here. Some trapped particles cannot be cleaned out; replace the filter when cleaning intervals become too short for practical use, or when noticeable cutting-power loss persists after thorough cleaning.
  • Historical guidance for these named models and filter configurations only; no successor-model fitment, universal interchange or material identity inferred from a shared part number. No hardware operation was performed.

Source: TI 38/1996, p. 1 · TI 38/1996, p. 2 — Complete filter-material and servicing guidance; exact model summary rows and remarks.

Referenced bulletin evidence: TI 31/1995, p. 1 — Header and contents establish 024/026 scope; contrast with printed 051/076 footnote in TI38.

Part numbers (1)
  • 1111 120 1601 — Air filterunchanged material-revision number · 051 / 076; TI38/1996 row and configuration conditions

Wrong number or missing part for the 050, 051? Report a correction →