Stihl 1122 · Section M · 12 of 16 · 35 parts
Carburetor WJ-67A
Fits MS 650.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (35)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1122 121 5604 | Fixed jet 0.64 | 1 |
| 2 | 1110 121 5100 | Inlet needle | 1 |
| 3 | 1117 122 3005 | Spring | 1 |
| 4 | 1117 121 9200 | Spindle | 1 |
| 5 | 1117 121 5000 | Inlet control lever | 1 |
| 6 | 1114 122 7400 | Round head screw | 1 |
| 7 | 1115 121 5401 | Valve jet | 1 |
| 8 | 1122 121 0700 | Cup plug | 1 |
| 9 | 1116 129 0900 | Gasket | 1 |
| 10 | 1117 121 4700 | Metering diaphragm | 1 |
| 11 | 1122 121 0805 | End cover | 1 |
| 12 | 1121 122 7101 | Screw | 4 |
| 13 | 1115 121 3301 | Throttle shutter | 1 |
| 14 | 1115 122 7400 | Round head screw | 2 |
| 15 | 1128 122 3003 | Spring | 2 |
| 16 | 4203 122 3600 | Sealing ring | 1 |
| 17 | 1122 122 6802 | Low speed adjustment screw | 1 |
| 18 | 1122 122 6706 | High speed adjustment screw | 1 |
| 19 | 1122 122 6200 | Idle speed adjustment screw | 1 |
| 20 | 1122 122 3200 | Torsion spring | 1 |
| 21 | 1122 120 7101 | Throttle shaft with lever | 1 |
| 22 | 1110 122 9300 | Clip | 1 |
| 23 | 1106 122 7400 | Round head screw | 1 |
| 25 | 1122 120 7200 | Choke shaft with lever | 1 |
| 26 | 1117 122 9000 | E-clip | 1 |
| 27 | 1114 121 7800 | Strainer | 1 |
| 28 | 1115 121 4800 | Pump diaphragm | 1 |
| 29 | 1115 129 1100 | Gasket | 1 |
| 30 | 1115 120 0800 | End cover | 1 |
| 31 | 1121 122 7101 | Screw | 4 |
| 32 | 1122 121 2900 | Choke shutter | 1 |
| 33 | 1122 121 7700 | Clamp | 1 |
| 34 | 1122 121 5603 | Fixed jet 0.62 option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1122 120 0621 | Carburetor WJ-67A → replaced by 1122 120 0618 TI 27/2003 | 1 |
| — | 1122 007 1060 | Set of carburetor parts Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · MS 650
MS 650 service aids: carburetor kit, grease and taper degreasant
No new special tools does not mean that no existing special tools are required.
- Carburetor parts kit 1122 007 1060 is listed for servicing the carburetor; contents and exact carburetor designation are not given. The later WJ-67A sheet is a model-specific navigation anchor, not evidence that the kit or these settings cover WJ-76A, WJ-69B or every revision.
- Lubricating grease 0781 120 1111, 225 g tube: oil seals, oil-pump drive, sprocket bearing, chain tensioner, sliding/bearing points on throttle trigger, brake lever and interlock lever. These are the listed interfaces, not permission to grease clutch friction surfaces.
- Clean crankshaft stub and flywheel taper using standard commercial solvent-based degreasant WITHOUT chlorinated or halogenated hydrocarbons. No product number is specified.
- No NEW special servicing tools are required for MS 650; page 5 still names existing puller 5910 890 4500 and setting disc 5910 893 6600. This is not a tool-free service claim.
- Historical TI10/2005 MS 650 guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.
Source: TI 10/2005, p. 3 · TI 10/2005, p. 5 — MS 650 service aids: carburetor kit, grease and taper degreasant.
Part numbers (2)
- 1122 007 1060 — Carburetor parts kitListed servicing aid; contents not enumerated · MS 650; see note restrictions
- 0781 120 1111 — Lubricating grease, 225 gOnly listed lubrication interfaces · MS 650; see note restrictions
Service note · MS 650
MS 650 carburetor limiter construction and adjustment scope
The illustrated carburetor is not identified by a WJ model number in this TI.
- Factory standard setting is intended for most operating conditions. User correction of H and L is limited by the carburetor-body stops to 270° (about 3/4 turn), with fine adjustment possible for conditions such as altitude; this section gives no separate numerical altitude correction.
- Figure 178TI006 KN identifies limiter caps (1), H screw WITH sealing ring (2), L screw WITH sealing ring (3), and idle-speed screw (4). Caps fit over the knurled screw heads. Do not omit sealing rings or infer that the caps themselves are the screw seals.
- The bulletin does not name WJ-67A, WJ-76A or WJ-69B. The WJ-67A sheet is only a navigation anchor; these instructions are not asserted for every later MS 650 carburetor. If started during repairs, country-specific regulations and instruction-manual precautions apply.
- Historical TI10/2005 MS 650 guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.
Source: TI 10/2005, p. 4 — MS 650 carburetor limiter construction and adjustment scope.
No additional parts-table entry added.
Service note · MS 650
MS 650 limiter removal: align both lugs before extraction
Removed caps are damaged and must not be reused.
- For damaged adjusting-screw replacement or carburetor cleaning: turn H cap COUNTERCLOCKWISE to its stop so its lug aligns with the carburetor-body slot. Turn L cap CLOCKWISE to its stop, then BACK OFF 1/4 TURN so its lug aligns with its slot; L cap lug is at right angles to the screw slot.
- Screw puller 5910 890 4500 COUNTERCLOCKWISE until the cap is pulled off. When entering the L cap, prevent the cap rotating with the puller; its lug must remain visible through the body slot. Screwdriver-slot angle alone is not a substitute for LUG-TO-SLOT ALIGNMENT.
- DO NOT REINSTALL USED CAPS: removal damages them. This uncapped servicing step is separate from standard adjustment, for which caps remain installed.
- Historical TI10/2005 MS 650 guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.
Source: TI 10/2005, p. 5 — MS 650 limiter removal: align both lugs before extraction.
Part numbers (1)
- 5910 890 4500 — Limiter-cap pullerCounterclockwise extraction with aligned lugs · MS 650; see note restrictions
Service note · MS 650
MS 650 uncapped basic setting: turns, rpm sequence and restart limit
One-turn baselines precede measured adjustment; stop if the L peak exceeds 3700 rpm.
- Check air filter and spark-arresting screen, clean or replace as necessary; check fuel filter and replace as necessary. Setting disc 5910 893 6600 on the carburetor screwdriver simplifies adjustment.
- With limiter caps removed, start with adjusting screws against their seats: open H ONE FULL TURN and L ONE FULL TURN. These are uncapped basic settings, NOT the capped standard 3/4-turn H and 1/4-turn L settings.
- Follow the printed order with ±200 rpm tolerance: (1) LA to 3300 rpm; (2) turn L either direction to maximum engine speed. If this peak is GREATER THAN 3700 rpm, ABORT AND RESTART AT STEP 1. (3) LA to 3300 again; (4) L to 2500; (5) H to maximum 13,500 rpm; (6) secure NEW limiter caps. The engine specification states the maximum with bar and chain fitted.
- A too-lean setting risks engine damage from insufficient lubrication and overheating. A one-turn baseline alone is not completed adjustment, and this historical sequence is not a remotely executed engine test.
- Historical TI10/2005 MS 650 guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.
Source: TI 10/2005, p. 2 · TI 10/2005, p. 5 · TI 10/2005, p. 6 — MS 650 uncapped basic setting: turns, rpm sequence and restart limit.
Part numbers (1)
- 5910 893 6600 — Setting discBasic-setting aid on carburetor screwdriver · MS 650; see note restrictions
Service note · MS 650
MS 650 replacement caps: align the lugs and seat flush
New-cap fitting follows the uncapped basic-setting procedure.
- DO NOT REINSTALL USED LIMITER CAPS. Fit NEW caps with lugs positioned as the arrows in figure 200TI015 KN on page 6 show. Push onto the adjusting screws until FLUSH WITH THE CARBURETOR BODY (1).
- The illustrated lug positions, not screwdriver-slot angle alone, determine orientation. The section supplies no cap-fitting tool number or cap order number; no number is invented from the catalog.
- Historical TI10/2005 MS 650 guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.
Source: TI 10/2005, p. 6 — MS 650 replacement caps: align the lugs and seat flush.
No additional parts-table entry added.
Service note · MS 650
MS 650 capped standard setting: H to stop, L back one-quarter turn
The engine is shut off and limiter caps stay installed.
- DO NOT REMOVE LIMITER CAPS for standard setting. SHUT OFF THE ENGINE. Check/clean/replace air filter and spark-arresting screen if fitted; check fuel filter and replace as necessary.
- Turn H COUNTERCLOCKWISE to its stop (maximum 3/4 turn). Turn L CLOCKWISE to its stop, then BACK OFF 1/4 TURN. Page 2 summarizes capped L=1/4 turn, H=3/4 turn, no further than the stop. These are cap-stop references, not uncapped screw-seat baselines.
- No additional idle-problem procedure, catalytic 7/8-turn setting or altitude turn increment is supplied here; do not import MS 440/MS 460 instructions merely because the drawings look similar.
- Historical TI10/2005 MS 650 guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.
Source: TI 10/2005, p. 2 · TI 10/2005, p. 6 — MS 650 capped standard setting: H to stop, L back one-quarter turn.
No additional parts-table entry added.
Wrong number or missing part for the MS 650? Report a correction →