← 021/023/025 · MS 210/230/250

Stihl 1123 · Section B · 2 of 17 · 24 parts

Engine housing

Fits MS 250, MS 250 C.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021223456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (24)

PosPart numberDescriptionQty
1 1123 020 3003 Engine housing 1
2 1123 020 3027 Engine housing 1
3 1128 640 9100 Valve 1
4 1123 162 7800 Flat spring 1
5 1123 664 2400 Collar screw Fitment / change note → 2
6 1123 790 9900 Annular buffer 1
7 1123 790 9900 Annular buffer 2
8 9075 478 4155 Pan head self-tapping screw IS-D5x24 3
9 1123 791 7300 Plug 3
10 not sold separately Spur gear not available as a separate item 1
11 not sold separately Adjusting screw not available as a separate item 1
12 1123 640 1900 Tensioner slide 1
13 1123 664 1400 Thrust pad 1
14 1123 664 2200 Cover 1
15 9075 478 3015 Pan head self-tapping screw IS-D4x15 1
16 0000 350 0526 Filler cap 1
17 9645 948 2470 O-ring 23x3 1
18 0000 350 0525 Filler cap 1
19 9645 948 7734 O-ring 25x3.5 1
20 1123 358 7703 Hose 1
21 0000 350 3500 Pickup body 1
22 0000 967 3662 Warning pictogram MS 1
Not numbered on the diagram — assemblies, kits and options
— 1123 007 1000 Chain tensioner kit option 1
— 1123 007 1004 Spur gear / chain adjusting screw kit 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · MS 210 / MS 230 / MS 250

MS 210, MS 230, MS 250: oversized repair stud at 16 Nm

1123 664 2400 (8 mm) → 1123 664 2405 (9 mm); damaged polymer-housing threads only.

  • Exact table scope: MS 210, MS 230, MS 250. Standard stud 1123 664 2400 has diameter 8 mm; repair stud 1123 664 2405 has diameter 9 mm (1 mm larger). Required repair-stud tightening torque: 16 Nm. This is a conditional repair, not a routine replacement or a standard-stud torque specification.
  • Use only when the housing thread is damaged or stripped and the standard collar screw cannot reach its specified tightening torque. If the housing is cracked or completely destroyed around the threads, the repair stud CANNOT be used; replace the entire engine housing.
  • DO NOT drill out the mounting hole. Position the repair stud by hand so it engages the EXISTING thread; use the stud driver to insert it PERPENDICULAR to the supporting surface, tighten to the listed repair torque, then unscrew the driver. Select the driver by the actual shaft geometry described in section1; no model-specific driver is inferred from the repair table.
  • Loctite is NOT recommended for repair studs in polymer engine housings (section2); section3 also says Loctite is not used for studs in polymer housings. Do not transfer the magnesium-crankcase Loctite 270 rule to this repair.
  • No repair solution is offered for UNLISTED chain saws in this bulletin. No serial threshold, permission for unlisted model suffixes, or applicability beyond the named models is supplied.
  • Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.

Source: TI 29/2011, p. 2 · TI 29/2011, p. 3 — MS 210, MS 230, MS 250: oversized repair stud at 16 Nm.

Part numbers (2)
  • 1123 664 2400 — Standard stud, diameter 8 mmstandard-stud · MS 210, MS 230, MS 250: oversized repair stud at 16 Nm
  • 1123 664 2405 — Oversized repair stud, diameter 9 mmconditional-repair · MS 210, MS 230, MS 250: oversized repair stud at 16 Nm

Wrong number or missing part for the MS 250, MS 250 C? Report a correction →