← 084 · 088 · MS 780/880/881

Stihl 1124 · Section O · 14 of 14 · 9 parts

Tools, Extras

Fits 088.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1234567
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (9)

PosPart numberDescriptionQty
1 1129 890 3401 Combination wrench 1
2 0812 370 1000 Screwdriver T27x120x70 1
3 0000 890 2300 NLA Screwdriver 1
4 0000 891 0801 NLA Tool roll 1
5 0000 792 9130 Chain scabbard 1
6 0000 792 9133 Chain scabbard extension up to 90 cm 1
7 1110 893 4000 Filing gauge option 1
Not numbered on the diagram — assemblies, kits and options
— 1121 890 1400 Tool kit 1
— 0751 010 1110 Lead 10 m / 33' not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 088

088: gasket and carburetor service aids

Launch servicing-aid numbers do not establish kit contents.

  • Gasket set 088 1124 007 1051, carburetor parts kit 1124 007 1060 and gasket panel 088 0457 281 2204 are listed as new servicing aids. Contents are not enumerated; no kit-to-every-later-carburetor assertion is inferred from the linked IPL assembly.
  • Other tools/aids and general tightening torques are referred to the separate 088 service manual. No unstated torque is filled in from 084 or a successor model.
  • The bulletin says all repair times are the same as 084, but gives no operation-by-operation times. It also announces a separate 088 illustrated parts list; neither statement proves another document was reviewed here.
  • If started during repairs or maintenance, the source requires compliance with local regulations and owner-manual safety precautions. This offline reference work does not start a machine.

Source: TI 35/1996, p. 7 · TI 35/1996, p. 8 — Sections4.2,5 repair preface,5.3–5.4 and6.

Part numbers (3)
  • 1124 007 1051 — 088 gasket setServicing aid · 088; contents unspecified
  • 1124 007 1060 — Carburetor parts kitServicing aid · 088; launch carburetor; contents unspecified
  • 0457 281 2204 — 088 gasket panelServicing aid · 088; not a torque table

Historical fitment · 088

088: leakage-test preparation and pressures

Replace the decompression valve with the specified plug before the test.

  • Flange 1124 850 4205 seals the muffler opening for leakage testing. Plug 1122 025 2200 must be installed instead of the decompression valve before the leakage test; the source refers to the service manual for the full procedure.
  • The decompression valve is removed/installed with a standard deep-well 13-mm socket. The adjacent tightening torque is 14 Nm (10.3 lbf.ft); do not apply it as a general cylinder, flange or carburetor torque.
  • Printed engine pressure test: 0.6 bar (8.7 psi); engine vacuum test: 0.6 bar (8.7 psi). The vacuum value is a magnitude in the vacuum-test row, not positive pressure or an absolute-pressure statement. Carburetor pressure test: 0.4 bar (5.8 psi).
  • No dwell time, permissible leak-down, complete port-sealing sequence or carburetor setup is printed. These values alone are not a complete executable test or a verified test result.

Source: TI 35/1996, p. 7 · TI 35/1996, p. 8 — Section4.1 flange and section 5.2.1 entire test data.

Part numbers (2)
  • 1124 850 4205 — Muffler-opening sealing flangeLeakage-test tool · 088; muffler opening
  • 1122 025 2200 — Decompression-port plugLeakage-test prerequisite · 088; replaces decompression valve

Wrong number or missing part for the 088? Report a correction →