Stihl 1130 · Section D · 4 of 10 · 32 parts
Rewind starter, Ignition system
Fits 018.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1130 080 1800 | Fan housing | 1 |
| 2 | 1110 084 9102 | Bushing | 1 |
| 3 | 1123 195 0400 | Rope rotor | 1 |
| 4 | 1125 195 7200 | Pawl | 1 |
| 5 | 0000 958 0923 | Washer | 1 |
| 6 | 1118 195 3500 | Spring | 1 |
| 7 | 1129 190 0601 | Rewind spring | 1 |
| 8 | 0000 195 8200 | Starter rope Ø 3x800 mm | 1 |
| 9 | 1121 195 3400 | Starter grip | 1 |
| 10 | 0000 190 3402 | Starter grip ElastoStart Ø 3 mm | 1 |
| 11 | 0000 195 8200 | Starter rope Ø 3x800 mm | 1 |
| 12 | 0000 195 7001 | Cap | 1 |
| 13 | 1130 967 1501 | Model plate 018 | 1 |
| 14 | 1130 967 1502 | Model plate 018 C | 1 |
| 15 | 9075 478 4155 | Pan head self-tapping screw IS-D5x24 | 5 |
| 16 | 9104 003 8733 | Self-tapping screw P4x16 | 1 |
| 17 | 1130 400 1201 | Flywheel Fitment / change note → | 1 |
| 18 | 0000 955 0802 | Collar nut M8x1 | 1 |
| 19 | 1130 400 1302 | Ignition module Fitment / change note → | 1 |
| 20 | 1128 405 1000 | Spark plug boot | 1 |
| 21 | 0000 998 0604 | Torsion spring | 1 |
| 22 | 1130 440 1101 | Short circuit wire | 1 |
| 23 | not sold separately | Terminal socket 4.8-1 not available as a separate item | 1 |
| 24 | 0751 030 8467 | Grommet no longer available from factory | 1 |
| 25 | 0751 030 8490 | Terminal socket 3.5 no longer available from factory | 1 |
| 26 | 1130 405 8000 | Insulator | 2 |
| 27 | 1130 440 2201 | Ground wire 125 mm / 4 15/16'' | 1 |
| 28 | 0751 030 8953 NLA | Terminal socket 4.8-1 no longer available from factory | 1 |
| 29 | 0751 030 8969 | Terminal socket A5-1.5 no longer available from factory | 1 |
| 30 | 1130 448 1201 | Lead retainer | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1130 080 2100 | Fan housing with rewind starter | 1 |
| — | 1130 080 2105 NLA | Fan housing with rewind starter | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 018
018: series 1130 replacement ignition assignment
1130 400 1302 and the listed flywheel pairing for series 1130; ignition lead not replaceable.
- Listed configuration: 1130 400 1302 with flywheel 1130 400 1201.
- The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.
Part numbers (2)
- 1130 400 1302 — Replacement ignition moduleAssigned replacement · 018, series 1130, only with the listed flywheel branch
- 1130 400 1201 — Listed configuration flywheelRequired pairing · 018, series 1130; listed configuration only
Service note · 018 / 018 C
018 and 018 C: launch equipment and engine design
The C version combines quick chain tensioning, ElastoStart and a decompression valve; those are not standard-version promises.
- The 018 is described as a development of the 017, with the same applications. It is offered as standard 018 and 018 C; the latter has quick chain tensioner, ElastoStart and decompression valve. The cover photograph specifically shows an 018 C with Picco Micro Mini cutting attachment. Neither the photograph nor the shared family establishes those convenience features on every standard 018.
- The descriptions cover only differences from the 017. The single-cylinder two-stroke engine has a machined crankshaft, described as optimizing the big-end bearing and high-speed characteristics, a four-port cylinder and a two-ring piston. The cylinder drawing 140TI002 KN illustrates the four-port mixture-flow arrangement; it supplies no port dimensions or machining instructions.
- Improved mixture control, cleaner combustion and lower emissions are the bulletin’s design claims, not independent measurements. No crankshaft, cylinder or piston part numbers or 017-to-018 conversion instructions are supplied here.
- Historical TI 42/1998, series 1130. This is the launch-era 018/018 C evidence, not a specification for MS 180 or every later 018 carburetor/configuration. No serial threshold, current stock or physically tested interchange is established. No hardware operation was performed.
Source: TI 42/1998, p. 1 · TI 42/1998, p. 2 — Complete introduction,cover photograph and section1 engine/cylinder/piston;140TI002 KN.
No additional parts-table entry added.
Service note · 018 / 018 C
018: ignition timing and launch-module description
Timing is specified at 8,000 rpm, not at idle; the TI gives no ignition-module replacement number.
- The ignition module is described as optimized for longer spark duration and improved acceleration. This qualitative claim does not establish a new part number, a retrofit or physical interchange with 017 or later models.
- Ignition timing is 1.6–2.3 mm (0.06–0.09 in) B.T.D.C. at 8,000 rpm, exactly the specified measurement condition. This is not a flywheel air gap, idle setting or operating-speed authorization. The TI provides no measurement procedure or module part number.
- Historical TI 42/1998, series 1130. This is the launch-era 018/018 C evidence, not a specification for MS 180 or every later 018 carburetor/configuration. No serial threshold, current stock or physically tested interchange is established. No hardware operation was performed.
Source: TI 42/1998, p. 2 · TI 42/1998, p. 3 — Section1 ignition and complete section2.3.
No additional parts-table entry added.
Service note · 018
018: later workshop tightening torques and thread-reuse limits
The 2000-06 manual gives 13 fastener values; only the hand-guard screw carries the approximately 1 Nm reuse reduction.
- This is the 018 baseline in the later 017/018 workshop manual RA_143_00_01_03, cover edition 2000-06; the 2006 print-production timestamp is not the edition. TI42/1998 delegates to the 017 manual but supplies no numbers. These later values are not proof of the exact 1998 edition or every earlier/later hardware revision. No MS 170/MS 180 values are substituted.
- The introduction requires matching IPLs and engineering-change TIs, with standardized repair and troubleshooting work delegated to separate handbooks. Its dealer-service notice remains part of the private source. This note reviews the torque table, not complete disassembly, assembly or operating instructions.
- Plastoform screws are for polymer components; DG screws are for lightmetal. They form a permanent thread on first installation. The manual permits repeated removal/refitting only with the specified torque and says a TORQUE WRENCH is essential. Match both fastener and joint; the same IS-DG 5x24 size has four different torque entries.
- IS-DG 5x24 spline screw: ignition module/cylinder: 7.5 Nm (5.6 lbf.ft); crankcase: 8.0 Nm (5.9 lbf.ft); fan housing/crankcase: 4.5 Nm (3.3 lbf.ft); crankcase/cylinder—bar mounting: 9.5 Nm (7.0 lbf.ft). The wrapped “bar mounting” text belongs to that 9.5 Nm row, not an added torque value.
- M8 collar screw, crankcase: 16.0 Nm (11.8 lbf.ft), with remark 1 requiring adhesive 0786 111 1101 (Loctite 243). M12x1L flange nut, clutch: 50.0 Nm (37.0 lbf.ft). M5 flange nut, carburetor: 3.5 Nm (2.6 lbf.ft). M5 nut, muffler/cylinder: 7.0 Nm (5.2 lbf.ft).
- M8x1 flange nut, flywheel: 27.5 Nm (20.3 lbf.ft). M14x1.25 spark plug: 25.0 Nm (18.5 lbf.ft). These are tightening torques, not the engine’s 1.75 Nm output torque or the 8,000 rpm timing condition.
- IS-P 4x12 screw, hand guard/fan housing: 1.7 Nm (1.25 lbf.ft), marked remark 2. IS-DG 5x16 panhead screw, engine housing/spiked bumper: 3.7 Nm (2.7 lbf.ft). IS-P 4x19 screw, handle molding/handle frame: 2.0 Nm (1.5 lbf.ft).
- For an existing P or DG thread, place the screw in its hole and rotate COUNTERCLOCKWISE until it drops slightly, then tighten CLOCKWISE to the specified torque. This re-engages the existing thread rather than cutting another. This screw-refitting instruction is distinct from the carburetor LD screw’s left-hand adjustment.
- Remark 2 permits torque reduction by approximately 1 Nm (0.7 lbf.ft) when refitting in an existing thread. ONLY the hand guard/fan housing IS-P 4x12 row bears this remark; do not subtract 1 Nm from every reused fastener. The note on adhesive says heating with a hot-air blower (hair dryer) makes release easier and explicitly cautions about polymer components; it is not a blanket heating instruction.
- All 13 table rows, both remarks and the complete thread-refitting/adhesive context were reviewed on original PDF 6. Values and imperial equivalents are preserved as printed, not newly recalculated. Exact 1998 source edition, repair-time and IPL dependencies are documented source gaps, not substituted by this later manual. No hardware operation was performed.
TI dependency: TI 42/1998, p. 5 — TI42 section5.2 dependency;later2000-06 workshop section2.6,not torques printed in1998TI.
Later manual evidence: STIHL 017, 018 workshop manual (2000-06), section Cover,introduction andcomplete2.6 (printed5), PDF pages 1, 3, 6
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the 018? Report a correction →