← 017/018 · MS 170/180

Stihl 1130 · Section K · 10 of 10 · 17 parts

Handle frame, Tools

Fits 018.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161723456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (17)

PosPart numberDescriptionQty
1 1130 791 4901 Handle frame 1
2 1130 182 1502 Throttle rod 1
3 1123 791 2800 Annular buffer 1
4 1123 791 7305 Plug 1
5 1123 791 7300 Plug 1
6 1130 182 0800 Lockout lever 1
7 1130 182 1000 Throttle trigger 1
8 1117 182 4500 Torsion spring 1
9 1130 791 0601 Handle molding 1
10 9074 478 3075 Pan head self-tapping screw IS-P4x19 2
11 0000 967 3632 Warning pictogram MS 1
12 0000 967 3500 NLA Instruction label 1
13 1129 890 3401 Combination wrench 1
14 0000 792 9128 Chain scabbard 1
15 0000 890 2300 NLA Screwdriver 1
16 0000 890 2305 Screwdriver 1
17 0812 370 1000 Screwdriver T27x120x70 option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 018 / 018 C

018: launch repair, filing and quick-tensioner kits

Launch accessory roles remain distinct. Later catalog kit lists use different carburetor callouts for the same four parts; they do not establish the 1998 kit contents.

  • Section3 lists STIHL repair kit 1130 900 5000, filing gauge 0000 893 4000 and quick chain tensioner kit 1123 007 1008 as special accessories for users. Section4 separately lists carburetor parts kit 1130 007 1061 as a service accessory.
  • The quick-tensioner kit listing is not an exploded kit bill of materials or a complete retrofit procedure. The standard/C launch distinction remains explicit. Do not transfer the separate 026 C crankcase/no-kit restriction from TI39 to this 018 kit, or transfer this kit approval to 026.
  • The TI does not identify the carburetor by maker/type, give individual kit contents or explain compatibility with later C1Q variants. The later 018 carburetor sheets describe their own configurations; their titles do not identify the 1998 BIS carburetor or prove this kit applies to every row.
  • Later-source comparison only — SCS 01-2012 (USA), original PL000002.dat: quick-tensioner kit 1123 007 1008 carries the explicit callout list 1–16 on document 80. Carburetor kit 1130 007 1061 carries 10, 11, 15, 16 on C1Q-S43B document 84 (49.2000), but 8, 9, 14, 15 on C1Q-S57C/C1Q-S57A document 8199. Callout numbers are local to each sheet, not interchangeable part numbers.
  • The two carburetor inclusion lists resolve to the same four later-catalog part numbers: gasket 1130 129 0901, metering diaphragm 1130 121 4700, pump diaphragm 1130 121 4800 and gasket 1130 129 0900. The native application guide independently confirms the including-item field using its exact 009 crankcase table and legend. This is later-catalog kit evidence, not proof of 1998 contents or universal C1Q compatibility.
  • The native legend uses a white-square symbol for including item No.; tilde-prefixed row identities are not that symbol. On the quick-tensioner sheet, included positions 6–9 have no separate orderable number and are marked (D), not available as separate item. The 1–16 list belongs to this exact 2012 sheet and is not a complete retrofit procedure. Historical availability code (ND) is retained in the evidence without an assumed meaning. The remaining historical dependencies are dispositioned below; kit contents are not reconstructed from similar part numbers.
  • The later 2000-06 STIHL 017/018 workshop manual, section 2.5 (PDF 5, printed 4), repeats user repair kit 1130 900 5000 but supplies no contents. Its service-accessory row prints carburetor parts kit 1130 007 1060, whereas the 018 launch TI prints 1130 007 1061. Preserve this source conflict: no supersession, typo correction or universal carburetor compatibility is established.
  • Filing gauge 0000 893 4000 is for 3/8-inch PMN at 0.45 mm (0.018 inch), explicitly confirmed by later TI 31/2007 page 3. That bulletin says sharpening set 5605 007 1026 was dropped from the range while the PMN gauge would remain available for five years as a spare part. This is a historical supply statement, not proof of current stock or an exact discontinuation date.
  • TI 31/2007 distinguishes the new 3/8-inch PMMC3 setting of 0.65 mm (0.025 inch) from PMN. Its harmonized sharpening set 5605 007 1027 is for 3/8-inch PM, PMC3, PMMC3 and 1/4-inch RM: round file 5605 772 4006 (5/32 inch / 4.0 mm), holder 5605 750 4327, gauge 1110 893 4000 (0.65 mm / 0.025 inch), and flat file 0814 252 3356. This does not substitute the 0.65-mm gauge for the launch PMN gauge. The PMMC3 depth gauge and marked upper humped drive link are lowered together; its service marking and PM/PMC3 sharpening method are chain-specific, not blanket instructions for PMN.
  • The 2012-01 Identification List gives filing gauge 0000 893 4000 AT 12 (PDF 38 / printed 19) and repair kit 1130 900 5000 AT 06 (PDF 215 / printed 196), with no structure symbol or successor number on either row. Its German legend defines AT as the last year of factory supply: 2012 and 2006 respectively, as stated by this historical register. Neither row proves current dealer stock, kit contents or a replacement part. The gauge entry is consistent with the five-year statement in TI 31/2007; no exact day or month is inferred.
  • The exact 1998 018 owner manual and the contents/instructions for user repair kit 1130 900 5000 remain unavailable in the checked collection. A verified inventory and exact-number text search covered 808 retained PDFs; original 2012 part and BOM tables contain neither user-accessory number. The repair-kit matches supply listings and an AT 06 withdrawal-register row, not a bill of materials. Missing later catalog rows do not revoke the TI listing. These are bounded source gaps, not proof of global absence or permission to substitute a different manual. Exact 1998 quick-tensioner/carburetor kit contents remain unestablished despite the separately reviewed 2012 lists.
  • Historical TI 42/1998, series 1130. This is the launch-era 018/018 C evidence, not a specification for MS 180 or every later 018 carburetor/configuration. No serial threshold, current stock or physically tested interchange is established. No hardware operation was performed.

TI dependency: TI 42/1998, p. 4 — Complete sections3 and4.

Referenced bulletin evidence: TI 31/2007, p. 3 — Complete page 3 sections 2–2.2: chain-specific sharpening, sets, gauge depth and historical availability; supplementary dependency review only.

Later manual evidence: STIHL 017, 018 workshop manual (2000-06), section 2.5 special accessories (printed 4); kit number conflict preserved, PDF pages 5 · STIHL Identification List (2012-01), section Cover, German AT/structure legend, gauge and repair-kit rows (printed 19 and 196), PDF pages 1, 2, 38, 215

Part numbers (4)
  • 1130 900 5000 — STIHL repair kitUser accessory · 018/018 C; TI 42/1998 only
  • 0000 893 4000 — Filing gaugeUser accessory · 018/018 C; TI 42/1998 only
  • 1123 007 1008 — Quick chain tensioner kitUser accessory · 018/018 C; TI 42/1998 only
  • 1130 007 1061 — Carburetor parts kitService accessory · 018/018 C; TI 42/1998 only

Service note · 018 / 018 C

018: delegated 017 torques, repair times and launch IPL

The launch TI delegates 017 torques and repair times and announces issue 4.98 of the 018 IPL; those exact historical sources remain unavailable in the checked collection.

Model-specific manual evidence: 018: later workshop tightening torques and thread-reuse limits · 018 reference: later warranty repair allowances and model-label caveat

  • Tightening torques are stated to be the same as017, with an explicit reference to theSTIHL017 Service Manual. No numeric fastener torques are printed on thisTI page. The linked2000-06 017/018 workshop baseline is now reviewed separately; its13 values andrestricted reuse remark are later evidence,not proof of the exact1998 edition.
  • Repair times are stated to be exactly the same as 017. The specified times assume trained personnel and a properly equipped service workshop; no labor-time values are provided here.
  • An 018 illustrated parts list is available and is to be included in the next microfilm/CD-ROM issue4.98. This is a historical publication/supply statement. The retained later2012 018 sheets do not prove exact contents of that1998 IPL or resolve later part revisions.
  • The exact 1998 service-manual and repair-time editions, and the 018 IPL announced for issue 4.98, are documented retained-corpus source gaps. Both alternate 017/018 workshop covers show 2000-06; a 2006 production margin on one copy is not its edition date. Both retained catalog registries link the exact 018 only to ten 2012 disc IPL sheets. The available 2012-01 repair timetable remains later evidence with its printed MS017/MS018 ambiguity.
  • TI42 review is complete with documented source gaps, including the owner manual and exact historical kit contents on page 4. No reconstruction of the 1998 IPL, unchanged-torque claim across editions, complete kit bill of materials or absence outside the checked collection is implied. The available later torque/time notes remain linked below; the exact 1998 cutting-attachment catalog is a separately documented gap.
  • Historical TI 42/1998, series 1130. This is the launch-era 018/018 C evidence, not a specification for MS 180 or every later 018 carburetor/configuration. No serial threshold, current stock or physically tested interchange is established. No hardware operation was performed.

Source: TI 42/1998, p. 5 — Complete sections5.2,5.3,6 and footer.

No additional parts-table entry added.

Service note · 018

018: later workshop tightening torques and thread-reuse limits

The 2000-06 manual gives 13 fastener values; only the hand-guard screw carries the approximately 1 Nm reuse reduction.

  • This is the 018 baseline in the later 017/018 workshop manual RA_143_00_01_03, cover edition 2000-06; the 2006 print-production timestamp is not the edition. TI42/1998 delegates to the 017 manual but supplies no numbers. These later values are not proof of the exact 1998 edition or every earlier/later hardware revision. No MS 170/MS 180 values are substituted.
  • The introduction requires matching IPLs and engineering-change TIs, with standardized repair and troubleshooting work delegated to separate handbooks. Its dealer-service notice remains part of the private source. This note reviews the torque table, not complete disassembly, assembly or operating instructions.
  • Plastoform screws are for polymer components; DG screws are for lightmetal. They form a permanent thread on first installation. The manual permits repeated removal/refitting only with the specified torque and says a TORQUE WRENCH is essential. Match both fastener and joint; the same IS-DG 5x24 size has four different torque entries.
  • IS-DG 5x24 spline screw: ignition module/cylinder: 7.5 Nm (5.6 lbf.ft); crankcase: 8.0 Nm (5.9 lbf.ft); fan housing/crankcase: 4.5 Nm (3.3 lbf.ft); crankcase/cylinder—bar mounting: 9.5 Nm (7.0 lbf.ft). The wrapped “bar mounting” text belongs to that 9.5 Nm row, not an added torque value.
  • M8 collar screw, crankcase: 16.0 Nm (11.8 lbf.ft), with remark 1 requiring adhesive 0786 111 1101 (Loctite 243). M12x1L flange nut, clutch: 50.0 Nm (37.0 lbf.ft). M5 flange nut, carburetor: 3.5 Nm (2.6 lbf.ft). M5 nut, muffler/cylinder: 7.0 Nm (5.2 lbf.ft).
  • M8x1 flange nut, flywheel: 27.5 Nm (20.3 lbf.ft). M14x1.25 spark plug: 25.0 Nm (18.5 lbf.ft). These are tightening torques, not the engine’s 1.75 Nm output torque or the 8,000 rpm timing condition.
  • IS-P 4x12 screw, hand guard/fan housing: 1.7 Nm (1.25 lbf.ft), marked remark 2. IS-DG 5x16 panhead screw, engine housing/spiked bumper: 3.7 Nm (2.7 lbf.ft). IS-P 4x19 screw, handle molding/handle frame: 2.0 Nm (1.5 lbf.ft).
  • For an existing P or DG thread, place the screw in its hole and rotate COUNTERCLOCKWISE until it drops slightly, then tighten CLOCKWISE to the specified torque. This re-engages the existing thread rather than cutting another. This screw-refitting instruction is distinct from the carburetor LD screw’s left-hand adjustment.
  • Remark 2 permits torque reduction by approximately 1 Nm (0.7 lbf.ft) when refitting in an existing thread. ONLY the hand guard/fan housing IS-P 4x12 row bears this remark; do not subtract 1 Nm from every reused fastener. The note on adhesive says heating with a hot-air blower (hair dryer) makes release easier and explicitly cautions about polymer components; it is not a blanket heating instruction.
  • All 13 table rows, both remarks and the complete thread-refitting/adhesive context were reviewed on original PDF 6. Values and imperial equivalents are preserved as printed, not newly recalculated. Exact 1998 source edition, repair-time and IPL dependencies are documented source gaps, not substituted by this later manual. No hardware operation was performed.

TI dependency: TI 42/1998, p. 5 — TI42 section5.2 dependency;later2000-06 workshop section2.6,not torques printed in1998TI.

Later manual evidence: STIHL 017, 018 workshop manual (2000-06), section Cover,introduction andcomplete2.6 (printed5), PDF pages 1, 3, 6

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · 018

018 reference: later warranty repair allowances and model-label caveat

The 2012-01 timetable lists 24 allowances, in minutes, under the printed MS017/MS018 group; these are not verified 1998 repair times or additive job estimates.

  • TI42/1998 says 018 repair times are exactly the same as 017 but prints no numeric times. This separate reference preserves the available later 2012-01 USA timetable, PDF14 (printed13), with its dealer instructions on PDF3–4 (printed2–3). It does not establish the exact 1998 times or prove unchanged allowances between editions.
  • The original second numeric column is headed “MS017 / MS018 / MS170 / MS180 / MS180C”. The MS prefix on 017/018 is printed in the source, not introduced by OCR. Its association with the legacy 017/018 is an explicit inference from those numerals and the shared series, not a corrected model name or verified applicability to an individual saw. No independent MS017/MS018 model identity, 018 C coverage, parts interchange or exact 1998 allowance is established.
  • These are flat-rate WARRANTY LABOR REIMBURSEMENT allowances for Authorized STIHL Dealers, in MINUTES, assuming STIHL-trained technicians, proper tools and workshop procedures. They are not measured owner repair durations, a retail price, a safe time limit, current warranty policy or instructions to run a machine. Diagnostic time, cleaning, repair and test running are included whenever applicable.
  • Allowances are NOT ADDITIVE. The 2012 instructions permit only one labor code per claim and generally use the highest applicable allowance for overlapping work. Piston/cylinder work considers leak testing, seals and carburetor work; ignition-module work considers stop-switch/wiring tests; carburetor work includes checking/replacing fuel lines and tank vents. Separate diagnoses/access may require more time, but the historical procedure requires distribution-center authorization to increase it—not summing all rows.
  • Code 1: Replace crankcase, crankcase gasket or re-seal crankcase; includes air leak test — 110 min; Code 2: Replace engine housing or cylinder shroud — 110 min; Code 3: Replace crankshaft main bearing(s); includes air leak test — 110 min; Code 4: Replace crankshaft seal(s); includes air leak test — 55 min.
  • Code 5: Replace tank filler cap — 3 min; Code 6: Replace cylinder and/or piston; includes air leak test and repair of components causing failure — 110 min; Code 7: Replace ignition module or flywheel; includes stop circuit test — 30 min; Code 8: Replace fuel tank line, tank vent, or fuel pick-up body — 25 min.
  • Code 9: Replace intake manifold or intake flange; includes leak test — 100 min; Code 10: Repair or replace carburetor; includes fuel system testing — 35 min; Code 11: Replace fuel tank housing — 20 min; Code 12: Replace oil pick-up/delivery line; includes oil output test — 30 min.
  • Code 13: Replace oil pump and/or drive gear; includes oil output test — 40 min; Code 14: Replace rear handle frame or handle housing — 20 min; Code 15: Repair or replace rewind starter — 20 min; Code 16: Repair or replace clutch, clutch shoes or clutch springs — 20 min.
  • Code 17: Repair chain brake; includes check for proper function — 20 min; Code 18: Replace muffler — 20 min; Code 19: Replace air filter or filter housing — 15 min; Code 22: Repair or replace stop switch; includes circuit testing — 20 min.
  • Code 35: Engine diagnosis only to determine failures requiring unit replacement — 25 min; Code 40: Miscellaneous repairs and other repairs not listed — 15 min; Code 45: Handling allowance only—no labor — 5 min; Code 50: No labor — 0 min.
  • Code 45 is a 5-minute handling allowance explicitly labeled “no labor”; code 50 is explicitly 0 minutes (“No labor”), not missing data or a zero-duration physical repair. Code 35 is limited to diagnosis of failures requiring unit replacement. The printed “chain break” in code 17 is rendered here as chain brake; its function-check requirement remains unchanged.
  • All 24 rows of this column were reviewed against the original, including the nonconsecutive codes. Other model columns are comparison context only, not imported evidence. Engine-housing/tool sheets are navigation anchors, not drawings of labor operations. No raw IPL or part supersession is changed and no hardware operation was performed.

TI dependency: TI 42/1998, p. 5 — TI42 section5.3 dependency; later2012-01 warranty repair timetable, PDF14/printed13 second numeric column, not values printed in1998TI.

Later manual evidence: STIHL Repair Timetables Manual (2012-01), section Cover; repair-time rules and warranty administration (printed2–3); complete second numeric column, Chain Saw Repair Times (printed13), PDF pages 1, 3, 4, 14

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Wrong number or missing part for the 018? Report a correction →