Stihl 1130 · Section A · 1 of 13 · 25 parts
Engine housing
Fits MS 180, MS 180 C.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (25)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1130 020 3002 | Engine housing | 1 |
| 2 | 1130 020 3011 | Engine housing | 1 |
| 4 | 1120 162 5200 | Pin | 1 |
| 5 | 1123 162 5200 | Pin | 1 |
| 6 | 1123 162 5205 | Pin | 2 |
| 7 | 1123 664 2400 | Collar screw Fitment / change note → | 2 |
| 7 | 1123 664 2400 | Collar screw Fitment / change note → | 1 |
| 8 | 1121 122 6600 | Collar screw | 2 |
| 9 | 1123 664 2402 NLA | Collar screw | 1 |
| 10 | 1130 084 8303 | Reflector foil | 1 |
| 11 | 1130 145 3400 | Heat shield | 2 |
| 12 | 9104 003 8600 NLA | Self-tapping screw P3x10 | 2 |
| 13 | 1123 640 3200 NLA | Oil pump 0.55 | 1 |
| 14 | 1130 350 4400 | Oil tank | 1 |
| 15 | 0000 359 1241 | Sealing ring | 1 |
| 16 | 1130 647 9400 | Hose | 1 |
| 17 | 1123 640 3800 | Pickup body | 1 |
| 18 | 1130 350 0411 | Fuel tank | 1 |
| 19 | 0747 313 6810 | Valve | 2 |
| 20 | 1130 358 7701 | Hose | 1 |
| 21 | 0000 350 3500 | Pickup body | 1 |
| 22 | 1130 350 0500 | Filler cap | 2 |
| 23 | 0000 359 1240 | Sealing ring | 2 |
| 24 | 0000 350 0905 | Rope | 2 |
| 25 | 0000 353 0605 | Hook | 2 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · MS 170 / MS 180
MS 170, MS 180: oversized repair stud at 16 Nm
1123 664 2400 (8 mm) → 1123 664 2405 (9 mm); damaged polymer-housing threads only.
- Exact table scope: MS 170, MS 180. Standard stud 1123 664 2400 has diameter 8 mm; repair stud 1123 664 2405 has diameter 9 mm (1 mm larger). Required repair-stud tightening torque: 16 Nm. This is a conditional repair, not a routine replacement or a standard-stud torque specification.
- Use only when the housing thread is damaged or stripped and the standard collar screw cannot reach its specified tightening torque. If the housing is cracked or completely destroyed around the threads, the repair stud CANNOT be used; replace the entire engine housing.
- DO NOT drill out the mounting hole. Position the repair stud by hand so it engages the EXISTING thread; use the stud driver to insert it PERPENDICULAR to the supporting surface, tighten to the listed repair torque, then unscrew the driver. Select the driver by the actual shaft geometry described in section1; no model-specific driver is inferred from the repair table.
- Loctite is NOT recommended for repair studs in polymer engine housings (section2); section3 also says Loctite is not used for studs in polymer housings. Do not transfer the magnesium-crankcase Loctite 270 rule to this repair.
- No repair solution is offered for UNLISTED chain saws in this bulletin. No serial threshold, permission for unlisted model suffixes, or applicability beyond the named models is supplied.
- Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.
Source: TI 29/2011, p. 2 · TI 29/2011, p. 3 — MS 170, MS 180: oversized repair stud at 16 Nm.
Part numbers (2)
- 1123 664 2400 — Standard stud, diameter 8 mmstandard-stud · MS 170, MS 180: oversized repair stud at 16 Nm
- 1123 664 2405 — Oversized repair stud, diameter 9 mmconditional-repair · MS 170, MS 180: oversized repair stud at 16 Nm
Wrong number or missing part for the MS 180, MS 180 C? Report a correction →