Stihl 1135 · Section E · 5 of 15 · 24 parts
Ignition system, Wiring harness
Fits MS 361, MS 361 C.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (24)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1135 400 1203 | Flywheel | 1 |
| 2 | 1135 400 1201 | Flywheel | 1 |
| 3 | 1135 404 3500 | Generator | 1 |
| 4 | 1118 431 6600 NLA | Terminal pin no longer available from factory | 1 |
| 5 | 9022 313 0658 | Spline screw IS-M4x12 | 2 |
| 6 | 1121 442 0402 NLA | Insulating hose 35 mm / 1.4'' | 1 |
| 7 | 0000 955 0802 | Collar nut M8x1 | 1 |
| 8 | 1135 400 1300 | Ignition module | 1 |
| 9 | 0000 989 1002 | Grommet | 1 |
| 10 | not sold separately | Ignition lead 195 mm not available as a separate item | 1 |
| 11 | 1117 442 0905 | Insulating hose 110 mm / 4.3'' | 1 |
| 12 | 0000 998 0604 | Torsion spring | 1 |
| 13 | 1128 405 1000 | Spark plug boot | 1 |
| 14 | 9022 341 1019 | Spline screw IS-M5x20 | 2 |
| 15 | 1135 440 3000 | Wiring harness | 1 |
| 16 | 1135 440 3005 | Wiring harness | 1 |
| 17 | 1135 440 3002 | Wiring harness | 1 |
| 18 | 1135 440 3004 | Wiring harness | 1 |
| 19 | 1135 440 3001 | Wiring harness | 1 |
| 20 | 0000 903 1506 NLA | Hose tie | 1 |
| 21 | 0000 903 1506 NLA | Hose tie | 1 |
| 22 | 0000 989 0609 | Grommet | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m not illustratedoption | 1 |
| — | 0000 930 2251 | Ignition lead 10 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · MS 361 / MS 361 C
MS 361 and MS 361 C flywheel nut: reduced 28 Nm tightening torque
The torque change is not for MS 440, MS 460 or MS 341.
- For MS 361 and MS 361 C ONLY, crankshaft/flywheel connection torque is reduced from 24 lbf ft (33 Nm) to 21 lbf ft (28 Nm). These are FOOT-POUND values. The original cover and section 3 name MS 361/361 C; the retained extracted bulletin title includes MS 341, but the original pages do NOT support extending this torque to MS 341.
- Clean crankshaft taper and flywheel-hub bore using commercial solvent-based degreasant WITHOUT chlorinated or halogenated hydrocarbons. Inspect the integrally moulded key for damage and replace the flywheel if necessary; do not infer a separately replaceable key.
- Mount flywheel correctly with the integral key aligned to the groove. Fit the tightening nut indicated by the arrow and tighten to 21 lbf ft (28 Nm). No flywheel/nut order number, thread lubricant or alternative torque is specified. Do not apply this section to MS 440/MS 460 merely because they share the bulletin cover.
- Historical TI36/2005 English USA guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.
Source: TI 36/2005, p. 1 · TI 36/2005, p. 2 — MS 361 and MS 361 C flywheel nut: reduced 28 Nm tightening torque.
No additional parts-table entry added.
Wrong number or missing part for the MS 361, MS 361 C? Report a correction →