← MS 261 · MS 271 · MS 291

Stihl 1141 · Section A · 1 of 14 · 24 parts

Engine housing

Fits MS 271, MS 271 C, MS 291, MS 291 C.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11010111213141515161616171717181818192202122232434445556777888999
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (24)

PosPart numberDescriptionQty
1 1141 020 3001 Engine housing 1
2 1141 020 3003 Engine housing 1
3 1141 020 3005 Engine housing 1
4 1128 640 9100 Valve 1
5 0000 974 1200 Notched pin 2.6x8 1
6 0000 974 1200 Notched pin 2.6x8 1
7 1141 162 5205 Pin 1
8 1121 162 5200 Pin 1
9 1120 162 5200 Pin 1
10 1123 162 5200 Pin 1
11 1141 162 5205 Pin 1
12 0000 664 2404 Collar screw M8 1
13 0000 664 2411 Collar screw D9/M8 option 1
14 0000 664 2407 Collar screw M8 1
15 0000 664 2403 Collar screw D8 1
16 1117 640 3800 Pickup body 1
17 1141 647 9401 Hose 1
18 1141 791 5902 Stop buffer 1
19 0000 350 0504 Filler cap 1
20 9645 948 7734 O-ring 25x3.5 1
21 1141 141 7500 Pre-separator 1
22 9074 477 4130 Pan head self-tapping screw IS-P5x16 1
23 1141 656 7700 Chain catcher 1
24 9074 477 4438 Pan head self-tapping screw IS-P6x30 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · MS 271 / MS 291

MS 271, MS 291: oversized repair stud at 16 Nm

1123 664 2400 (8 mm) → 1123 664 2405 (9 mm); damaged polymer-housing threads only.

  • Exact table scope: MS 271, MS 291. Standard stud 1123 664 2400 has diameter 8 mm; repair stud 1123 664 2405 has diameter 9 mm (1 mm larger). Required repair-stud tightening torque: 16 Nm. This is a conditional repair, not a routine replacement or a standard-stud torque specification.
  • Use only when the housing thread is damaged or stripped and the standard collar screw cannot reach its specified tightening torque. If the housing is cracked or completely destroyed around the threads, the repair stud CANNOT be used; replace the entire engine housing.
  • DO NOT drill out the mounting hole. Position the repair stud by hand so it engages the EXISTING thread; use the stud driver to insert it PERPENDICULAR to the supporting surface, tighten to the listed repair torque, then unscrew the driver. Select the driver by the actual shaft geometry described in section1; no model-specific driver is inferred from the repair table.
  • Loctite is NOT recommended for repair studs in polymer engine housings (section2); section3 also says Loctite is not used for studs in polymer housings. Do not transfer the magnesium-crankcase Loctite 270 rule to this repair.
  • No repair solution is offered for UNLISTED chain saws in this bulletin. No serial threshold, permission for unlisted model suffixes, or applicability beyond the named models is supplied.
  • Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.

Source: TI 29/2011, p. 2 · TI 29/2011, p. 3 — MS 271, MS 291: oversized repair stud at 16 Nm.

Part numbers (2)
  • 1123 664 2400 — Standard stud, diameter 8 mmstandard-stud · MS 271, MS 291: oversized repair stud at 16 Nm
  • 1123 664 2405 — Oversized repair stud, diameter 9 mmconditional-repair · MS 271, MS 291: oversized repair stud at 16 Nm

Wrong number or missing part for the MS 271, MS 271 C, MS 291, MS 291 C? Report a correction →