Stihl 1143 · Section A · 1 of 14 · 16 parts
Engine housing
Fits MS 231, MS 231 C, MS 251, MS 251 C.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (16)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1143 020 3001 | Engine housing | 1 |
| 2 | 1143 020 3031 | Engine housing | 1 |
| 3 | 1143 020 3011 | Engine housing | 1 |
| 4 | 1128 640 9100 | Valve | 1 |
| 5 | 1123 664 2400 | Collar screw Fitment / change note → | 1 |
| 6 | 1123 664 2405 | Collar screw D9/M8 Fitment / change note → option | 1 |
| 7 | 1123 640 3800 | Pickup body | 1 |
| 8 | 1143 647 9401 | Hose | 1 |
| 9 | 1123 021 2800 | Insert | 1 |
| 10 | 1143 791 5900 | Stop buffer | 1 |
| 11 | 0000 350 0526 | Filler cap | 1 |
| 12 | 9645 948 2470 | O-ring 23x3 | 1 |
| 13 | 1143 140 7800 | Pre-separator | 1 |
| 14 | 9074 477 2995 | Pan head self-tapping screw IS-P4x12 | 1 |
| 15 | 0000 656 7700 | Chain catcher option | 1 |
| 16 | 9074 477 4438 | Pan head self-tapping screw IS-P6x30 option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · MS 231 / MS 251
MS 231, MS 251: oversized repair stud at 16 Nm
1123 664 2400 (8 mm) → 1123 664 2405 (9 mm); damaged polymer-housing threads only.
- Exact table scope: MS 231, MS 251. Standard stud 1123 664 2400 has diameter 8 mm; repair stud 1123 664 2405 has diameter 9 mm (1 mm larger). Required repair-stud tightening torque: 16 Nm. This is a conditional repair, not a routine replacement or a standard-stud torque specification.
- Use only when the housing thread is damaged or stripped and the standard collar screw cannot reach its specified tightening torque. If the housing is cracked or completely destroyed around the threads, the repair stud CANNOT be used; replace the entire engine housing.
- DO NOT drill out the mounting hole. Position the repair stud by hand so it engages the EXISTING thread; use the stud driver to insert it PERPENDICULAR to the supporting surface, tighten to the listed repair torque, then unscrew the driver. Select the driver by the actual shaft geometry described in section1; no model-specific driver is inferred from the repair table.
- Loctite is NOT recommended for repair studs in polymer engine housings (section2); section3 also says Loctite is not used for studs in polymer housings. Do not transfer the magnesium-crankcase Loctite 270 rule to this repair.
- No repair solution is offered for UNLISTED chain saws in this bulletin. No serial threshold, permission for unlisted model suffixes, or applicability beyond the named models is supplied.
- Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.
Source: TI 29/2011, p. 2 · TI 29/2011, p. 3 — MS 231, MS 251: oversized repair stud at 16 Nm.
Part numbers (2)
- 1123 664 2400 — Standard stud, diameter 8 mmstandard-stud · MS 231, MS 251: oversized repair stud at 16 Nm
- 1123 664 2405 — Oversized repair stud, diameter 9 mmconditional-repair · MS 231, MS 251: oversized repair stud at 16 Nm
Wrong number or missing part for the MS 231, MS 231 C, MS 251, MS 251 C? Report a correction →