Stihl 4116 · Section M · 12 of 16 · 27 parts
Gear head
Fits FS 500, FS 550, FS 550 L.
Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.
Parts (27)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 640 0512 | Gear housing | 1 |
| 2 | 4116 713 6500 | Screw plug | 1 |
| 3 | 9291 021 0140 | Washer 6.4 Fitment / change note → | 1 |
| 4 | 9022 341 1370 | Spline screw IS-M6x30 | 1 |
| 5 | 0000 953 1001 | Stud | 1 |
| 6 | 4116 640 7305 | Set of pinions | 1 |
| 7 | 4116 640 5101 | Grooved ball bearing | 1 |
| 8 | not sold separately | Slinger disc not available as a separate item | 1 |
| 9 | 9503 003 0210 | Grooved ball bearing 6001 | 1 |
| 10 | 9503 003 4951 | Grooved ball bearing 15x32x15-RS | 1 |
| 11 | 0000 958 1500 | Washer | 1 |
| 12 | 9455 621 1520 | Circlip 15x1 | 1 |
| 13 | 0000 958 3604 | Shim 0.1 mm | 1 |
| 14 | 0000 958 3605 | Shim 0.15 mm | 1 |
| 15 | 0000 958 3002 | Shim 0.2 mm | 1 |
| 16 | 9456 621 4480 | Circlip 42x1.75 | 1 |
| 17 | 4116 642 7601 | Collar nut M14x1.5 l/h thread | 1 |
| 18 | 4116 710 3800 | Thrust plate Ø 60 mm / 2 3/8" | 1 |
| 19 | 4116 717 2800 | Guard washer Ø 60 mm / 2 3/8'' | 1 |
| 20 | 4116 713 1600 | Thrust washer Ø 60 mm / 2 3/8" Fitment / change note → | 1 |
| 21 | 4116 713 1601 | Thrust washer Ø 70 mm Fitment / change note → | 1 |
| 22 | 4116 713 3100 | Rider plate | 1 |
| 23 | 4116 710 3810 | Thrust plate Ø 65 mm / 2 9/16" | 1 |
| 24 | 4116 717 2810 | Guard washer Ø 65 mm / 2 9/16'' | 1 |
| 25 | 4116 717 2702 | Guard ring | 1 |
| 26 | 0781 120 1118 | Gear lubricant 225 g option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4116 640 0115 | Gearhead M14 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 550
FS 550 gearhead: M14 left-hand mounting and optional guards
Reinforced output shaft, 1.33 ratio and separately identified thrust plate/guard ring.
- The reinforced output shaft has an M14 LEFT-HAND mounting thread, and mounting nut (3) is also M14 LEFT-HAND. The gear ratio is 1.33. These sections provide no mounting torque or explicit pitch; do not infer them from a generic M14 fastener.
- The 2.56 in (65 mm) thrust plate (1) is designed to prevent grass and dirt ingress. The hardened guard ring (2) is for special applications with the BRUSH KNIFE. Both are starred as SPECIAL ACCESSORIES in section 1; their drawing positions are not catalog part numbers.
- Page 6 separately states that mowing versions may come with the 65 mm thrust plate or the 60 mm plate plus separate grass deflector, depending on model and standard tool. Preserve that configuration-dependent supplied equipment alongside the section 1 accessory designation, rather than claiming the 65 mm plate is always optional or always supplied.
- Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.
Source: TI 44/1997, p. 2 · TI 44/1997, p. 5 · TI 44/1997, p. 6 — Section 1 gearhead/mounting with 340TI006 KN; section 2.2 and section 3.1 context.
No additional parts-table entry added.
Historical fitment · FS 550
FS 550: seven approved cutting tools in TI44/1997
Keep 225 mm chisel/scratcher blades distinct from the 250 mm scratcher blade.
- The complete approved roster here is AutoCut 40-4 (4005 710 2100), PolyCut 40-3 (4111 710 2100), cutting blade 255-8 (4000 713 3802), brush knife 350-3 (4110 713 4100), circular saw 225 CHISEL TOOTH (4110 713 4204), circular saw 225 SCRATCHER TOOTH (4000 713 4205), and circular saw 250 SCRATCHER TOOTH (4104 713 4200). Drawings 6+7 share an illustration but retain separate diameters/numbers.
- The approved 250 mm row is SCRATCHER TOOTH; no 250 mm chisel-tooth approval is supplied by this roster. Do not enlarge the cutting-tool approval using the broader transport-guard descriptions on page 7. Use the relevant mowing/circular-saw handle and required deflector/limit-stop configuration, not a blade-only fitment assertion.
- For circular saws, section 3.2 REQUIRES limit stop 4116 710 8201 for 225 mm or 4116 710 8206 for 250 mm. For mowing, section 3.1 specifies deflector 4116 713 4501 with the applicable thrust-plate/grass-deflector arrangement. The related guard note preserves these combinations.
- Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.
Source: TI 44/1997, p. 1 · TI 44/1997, p. 6 — Section 3 all seven rows and corresponding tool drawings; cover handle configuration.
Part numbers (7)
- 4005 710 2100 — AutoCut 40-4Listed approved FS 550 tool; matching guards required · FS 550; Section 3 all seven rows and corresponding tool drawings; cover handle configuration
- 4111 710 2100 — PolyCut 40-3Listed approved FS 550 tool; matching guards required · FS 550; Section 3 all seven rows and corresponding tool drawings; cover handle configuration
- 4000 713 3802 — Cutting blade 255-8Listed approved FS 550 tool; matching guards required · FS 550; Section 3 all seven rows and corresponding tool drawings; cover handle configuration
- 4110 713 4100 — Brush knife 350-3Listed approved FS 550 tool; matching guards required · FS 550; Section 3 all seven rows and corresponding tool drawings; cover handle configuration
- 4110 713 4204 — Circular saw 225 chisel toothListed approved FS 550 tool; matching guards required · FS 550; Section 3 all seven rows and corresponding tool drawings; cover handle configuration
- 4000 713 4205 — Circular saw 225 scratcher toothListed approved FS 550 tool; matching guards required · FS 550; Section 3 all seven rows and corresponding tool drawings; cover handle configuration
- 4104 713 4200 — Circular saw 250 scratcher toothListed approved FS 550 tool; matching guards required · FS 550; Section 3 all seven rows and corresponding tool drawings; cover handle configuration
Historical fitment · FS 550
FS 550: mowing deflectors and mandatory saw limit stops
225 mm and 250 mm saws need different stops; mowing has two thrust-plate arrangements.
- All mowing versions come standard with deflector 4116 713 4501 (drawing 1). Depending on model and standard cutting tool, the lower arrangement is EITHER a 2.56 in (65 mm) thrust plate (2), OR separate grass deflector 4116 710 2701 (3) COMBINED WITH a 2.36 in (60 mm) thrust plate (4), as on FS 360/420. The main mowing deflector and the separate grass deflector are different components, not alternatives to each other.
- For circular saw blades, limit stop 4116 710 8201 MUST be used for 8.9 in/225 mm blades; limit stop 4116 710 8206 MUST be used for 9.8 in/250 mm blades. A common gearhead or blade mounting thread does not waive these size-specific stops.
- The source does not provide a complete model/standard-tool matrix choosing between the two mowing lower arrangements, nor thrust-plate part numbers here. Do not fabricate either. The section 1 starred 65 mm plate/special brush-knife ring and page 6 configuration-dependent standard equipment remain distinct statements.
- Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.
Source: TI 44/1997, p. 2 · TI 44/1997, p. 6 — Sections 3.1/3.2 and 398TI003 KN; section 1 accessory context.
Part numbers (4)
- 4116 713 4501 — Main mowing deflectorStandard on mowing versions · FS 550; Sections 3.1/3.2 and 398TI003 KN; section 1 accessory context
- 4116 710 2701 — Separate grass deflectorCombined with 60 mm thrust plate · FS 550; Sections 3.1/3.2 and 398TI003 KN; section 1 accessory context
- 4116 710 8201 — Limit stop for 225 mm circular sawRequired · FS 550; Sections 3.1/3.2 and 398TI003 KN; section 1 accessory context
- 4116 710 8206 — Limit stop for 250 mm circular sawRequired · FS 550; Sections 3.1/3.2 and 398TI003 KN; section 1 accessory context
Service note · FS 550
FS 550: separate shaft, gearhead and seal lubricants
Keep three lubricant applications distinct; the carburetor kit names HD 22 and HD 23.
- STIHL gear lubricant 0781 120 1109, 3 oz/80 g tube, is for the DRIVE SHAFT IN THE DRIVE TUBE. Gear lubricant 0781 120 1117, 3 oz/80 g tube, is for the GEARHEAD. Lubricating grease 0781 120 1111, 13 oz/370 g tube, is for OIL SEALS. The TI does not state these products are interchangeable.
- Carburetor parts kit 4116 007 1061 explicitly lists Walbro HD 22 and HD 23. Gasket set 4116 007 1051 has no separate application text in its row; do not silently copy the carburetor-kit restriction or infer its component contents. Common service-kit availability does not establish identical HD 22/HD 23 adjustment settings.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 7 · TI 44/1997, p. 8 — Section4 lubricant rows and complete section5.2 servicing-aids table.
Part numbers (5)
- 0781 120 1109 — Drive-shaft gear lubricant;80 gPrinted application only · Only named models/configurations and restrictions in this note
- 0781 120 1117 — Gearhead lubricant;80 gPrinted application only · Only named models/configurations and restrictions in this note
- 0781 120 1111 — Oil-seal lubricating grease;370 gPrinted application only · Only named models/configurations and restrictions in this note
- 4116 007 1061 — Walbro HD22/HD23 carburetor parts kitPrinted application only · Only named models/configurations and restrictions in this note
- 4116 007 1051 — Set of gaskets; contents not specifiedPrinted application only · Only named models/configurations and restrictions in this note
Service note · FS 550
FS 550: all 20 historical repair-time entries
Decimal hours, with 0.1 hour equal to 6 minutes; trained and equipped workshop assumed.
- The times assume TRAINED PERSONNEL in a PROPERLY EQUIPPED SERVICE WORKSHOP. Values are decimal hours in tenths: 0.1 hour=6 minutes, not one minute. This table supplements the STIHL repair-times table; it is not a guarantee, current billing schedule or permission to add overlapping operations.
- Code 1: Crankcase, short block — 2.0 hours.
- Code 2: Crankshaft and/or bearings — 2.0 hours.
- Code 3: Crankcase, gasket, sealing — 2.0 hours.
- Code 4: Crankshaft seals — 1.2 hours.
- Code 5: Cylinder and/or piston — 1.0 hours.
- Code 6: Ignition — 0.5 hours.
- Code 7: Fuel hose, fuel supply — 0.3 hours.
- Code 8: Gear box, arbor assembly — 0.3 hours.
- Code 9: Carburetor — 0.7 hours.
- Code 10: Fan housing, clutch housing — 0.5 hours.
- Code 11: Front handle, throttle — 0.4 hours.
- Code 12: Recoil starter — 0.4 hours.
- Code 13: Clutch — 0.5 hours.
- Code 14: Drive tube, drive shaft — 0.5 hours.
- Code 15: Muffler — 0.3 hours.
- Code 16: Air filter, filter cover — 0.2 hours.
- Code 17: Stop switch — 0.3 hours.
- Code 18: Fuel tank — 0.8 hours.
- Code 19: Replace arbor gears — 0.6 hours.
- Code 20: Miscellaneous repairs — 0.5 hours.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 9 — Complete section6.4: all20 codes, units and workshop assumptions.
No additional parts-table entry added.
Service note · FS 550 / FS 360 / FS 420
FS 550: tool-specific handlebars and M 14x 1.5 pinion set
Complete gearhead includes housing and pinions; handle purposes remain separate.
- Handlebar 26, 4128 790 1701, is for MOWING. Handlebar 27, 4128 790 1715, is for CIRCULAR SAW BLADES. Complete control handle 28 is 4128 790 1300; throttle cable 29 is 4116 180 1104. The distinct handlebars are not an interchangeable-purpose claim.
- Complete gearhead 30, 4116 640 0104, INCLUDES gear housing 31, 4116 640 0511, and pinion set 32, 4116 640 7302. The pinion-set row explicitly prints M14x1.5; this does not supply a mounting torque. Page 2 separately establishes the left-hand mounting thread.
- Remark 1 extends handlebars 26/27 and COMPLETE gearhead 30 to predecessor FS 360/FS 420; it does not separately mark control handle 28, cable 29, gear housing 31 or pinion set 32. Keep inclusion and assembly-level applicability separate.
- Modification introduction is IN PROGRESS; no FS 550 introduction serial is printed. For component parts of assemblies not shown, the source delegates to the FS 500/550 parts list. Later IPL navigation is not proof of 1997 contents; this note does not fabricate the omitted component lists.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 10 — Section7 rows26–32, remark1, introduction status and component-list delegation.
Part numbers (7)
- 4128 790 1701 — Item26 mowing handlebar; remark1Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4128 790 1715 — Item27 circular-saw handlebar; remark1Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4128 790 1300 — Item28 complete control handleExact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
- 4116 180 1104 — Item29 throttle cableExact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
- 4116 640 0104 — Item30 complete gearhead including31/32; remark1Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4116 640 0511 — Item31 gear housingExact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
- 4116 640 7302 — Item32 pinion set M14x1.5Exact section7 row; assembly inclusions and remark1 retained · FS 550 table context; no separate predecessor remark on this row
Conditional replacement · FS 500 / FS 550
FS 500 / FS 550: shredder blade and complete deflector mounting
Initial installation requires blade 4000 713 3902 and complete deflector 4116 710 8103; the deflector shell alone is not the full kit.
- Section 1.1 introduces shredder blade 320-2 with optimized geometry/material and a specially developed robust deflector with riveted aluminium skirt. Drawing 398TI015 KN depicts the blade and deflector. The new deflector replaces 4116 710 8105 and is also suitable for the brush knife; this is not approval for every cutting tool.
- For initial installation, order BOTH shredder blade 4000 713 3902 and deflector assembly 4116 710 8103. The assembly comes with all necessary mounting hardware. The summary distinguishes complete assembly (items 5–12), new shell 4116 710 8104 (items 6 and 7) and previous deflector 4116 710 8105 (items 6–10). Do not treat these as identical kits.
- Drawing 398TI017 KN: stepped sleeve (1) fits over the drive tube and must be riveted in position to define the installed deflector position. The recommended thrust plate (2) is 65 mm diameter; thrust washer (3) is 70 mm diameter. Center the blade exactly on the thrust-plate shoulder and fit hardened guard ring (4) to protect the mounting nut. The diagram places plate below the blade and washer/guard ring above it. No rivet-hole coordinates, torque or unprinted guard-ring order number is inferred.
- The drawing callouts 1–4 on page 1 are NOT the summary item numbers on pages 2–3. Drawing 398TI019 SC shows blade 1, brush knife 2, circular blade 3, shell 5, clamp/nut 6/7, clamp/washer/screw 8/9/10, sleeve/rivet 11/12 and transport guard 13. The previous item 4 and unnumbered complete assembly are not invented as extra visible callouts.
- The table explicitly gives two square nuts, two washers and two M6x45 screws. Rivet A 4x8 has no printed quantity in this TI; the later IPL quantity is not silently substituted. New clamps replace 4116 716 6400 and 4116 716 6500 with 6402 and 6502 endings respectively; the unchanged fasteners retain their numbers.
- Transport guard 4116 790 3901 replaces 4116 790 3900 and now also fits the shredder blade. Remark 1 applies only to previous deflector 4116 710 8105 and previous transport guard: no longer available from factory. Remark 2 applies to both previous clamps: remain available. Introduction is in progress, not the clutch serial threshold in section 2.
- Historical TI34/1999 evidence only; availability and performance claims are dated source statements, not current stock or measured performance. Grouped IPL navigation does not add FS 550 L or other unlisted variants. No hardware operation or physical interchange verification.
Source: TI 34/1999, p. 1 · TI 34/1999, p. 2 · TI 34/1999, p. 3 — FS 500 / FS 550: shredder blade and complete deflector mounting; complete relevant text, drawings and table rows.
Part numbers (15)
- 4000 713 3902 — Shredder blade 320-2New; summary item 1 · FS 500 / FS 550
- 4116 710 8103 — Shredder deflector assembly, including items 5–12Complete initial-installation deflector · FS 500 / FS 550
- 4116 710 8105 — Previous deflector, including items 6–10Previous; remark 1 · FS 500 / FS 550
- 4116 710 8104 — Deflector, including items 6 and 7New shell subassembly; item 5 · FS 500 / FS 550
- 4116 716 6400 — ClampPrevious item 6; remark 2 · FS 500 / FS 550
- 4116 716 6402 — ClampNew item 6 · FS 500 / FS 550
- 9222 068 0900 — Square nut M6, twoUnchanged; item 7 · FS 500 / FS 550
- 4116 716 6500 — ClampPrevious item 8; remark 2 · FS 500 / FS 550
- 4116 716 6502 — ClampNew item 8 · FS 500 / FS 550
- 9291 021 0140 — Washer A 6.4, twoUnchanged; item 9 · FS 500 / FS 550
- 9022 341 1420 — Spline screw IS M6x45, twoUnchanged; item 10 · FS 500 / FS 550
- 4116 711 2501 — Stepped sleeveNew; item 11 · FS 500 / FS 550
- 9438 782 3170 — Rivet A 4x8New; item 12; no quantity printed in TI table · FS 500 / FS 550
- 4116 790 3900 — Transport guardPrevious item 13; remark 1 · FS 500 / FS 550
- 4116 790 3901 — Transport guardNew item 13; modified for shredder blade · FS 500 / FS 550
Conditional replacement · FS 500 / FS 550
FS 500 / FS 550: special 350-3 brush knife
Special blade 4000 713 4100 is compared with standard 4110 713 4100; the 70 mm washer is recommended.
- Section 1.2 describes special wear-resistant steel for particularly tough conditions, claiming almost twice the service life of identically shaped standard 4110 713 4100. This is the source comparison, not proof of an exact lifetime or a deletion/replacement of the standard blade.
- The 70 mm thrust washer is generally recommended for optimum brush-knife mounting; section 3 supplies number 4116 713 1601. Special mowing versions with brush knife had already shipped with the large washer. The washer cannot be used for STIHL Polycut 40-3. No universal cutting-head approval follows.
- Summary item 2 and drawing 398TI019 SC depict the three-arm knife. The new-column entry has a dash in the previous column; it does not say 4110 713 4100 was withdrawn. Cutting-tool introduction is in progress; no clutch serial is borrowed.
- Historical TI34/1999 evidence only; availability and performance claims are dated source statements, not current stock or measured performance. Grouped IPL navigation does not add FS 550 L or other unlisted variants. No hardware operation or physical interchange verification.
Source: TI 34/1999, p. 2 · TI 34/1999, p. 3 · TI 34/1999, p. 4 — FS 500 / FS 550: special 350-3 brush knife; complete relevant text, drawings and table rows.
Part numbers (3)
- 4000 713 4100 — Special brush knife 350-3New; summary item 2 · FS 500 / FS 550
- 4110 713 4100 — Standard brush knife 350-3Comparison version; not a deleted-part row · FS 500 / FS 550
- 4116 713 1601 — Thrust washer, 70 mmRecommended for brush-knife mounting · FS 500 / FS 550
Conditional replacement · FS 500 / FS 550
FS 500 / FS 550: 70 mm washer excludes Polycut 40-3
Thrust washer 4116 713 1601 replaces the 60 mm version for brush-knife mounting, but cannot be used with STIHL Polycut 40-3.
- Section 3 replaces 60 mm thrust washer 4116 713 1600 with 70 mm 4116 713 1601 to optimize brush-knife mounting. Special mowing versions with brush knife had already shipped with the larger washer.
- The new 70 mm thrust washer cannot be used for mounting STIHL Polycut 40-3. This is an explicit exclusion, not a generic all-head replacement or an inferred approval of any alternative washer/head combination.
- Introduction is in progress; no serial threshold is printed for this change. The clutch serial in section 2 must not be applied to this washer. Remark 1 says the previous washer remains available; a dash in the new column is not proof that the old part became unavailable.
- The footer TI49/1998 is a chronology pointer, not a delegated installation procedure. The entire final page, including blank regions and colophon, contains no further dimensions, torque or fitting conditions.
- Historical TI34/1999 evidence only; availability and performance claims are dated source statements, not current stock or measured performance. Grouped IPL navigation does not add FS 550 L or other unlisted variants. No hardware operation or physical interchange verification.
Source: TI 34/1999, p. 4 — FS 500 / FS 550: 70 mm washer excludes Polycut 40-3; complete relevant text, drawings and table rows.
Part numbers (2)
- 4116 713 1600 — Thrust washer, 60 mmPrevious; remains available · FS 500 / FS 550
- 4116 713 1601 — Thrust washer, 70 mmNew for stated mounting; excludes Polycut 40-3 · FS 500 / FS 550
Wrong number or missing part for the FS 500, FS 550, FS 550 L? Report a correction →