← FS 48, FS 52, FS 56 · FS 62, FS 66

Stihl 4123 · Section B · 2 of 12 · 27 parts

Rewind starter, Muffler

Fits FS 62, FS 66.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222324253456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (27)

PosPart numberDescriptionQty
1 4123 190 2000 Carrier 1
2 4123 195 7200 Pawl 1
3 0000 998 0609 Torsion spring Fitment / change note → 1
4 9460 624 0400 E-clip 4 1
5 9208 260 1110 Hexagon nut M8 1
6 4123 190 0400 Starter cover 1
7 not sold separately Hollow rivet 6.5x0.5x5.8 not available as a separate item 3
8 4126 084 9100 Bushing 1
9 4123 195 5400 Cover 1
10 4126 195 1600 Rewind spring 1
11 4123 195 0400 Rope rotor 1
12 0000 195 8200 Starter rope Ø 3x800 mm Fitment / change note → 1
13 4215 195 9000 Washer 1
14 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 1
15 4123 195 3400 Starter grip 1
16 4122 967 1500 Model plate FS 62 1
16 4123 967 1501 Model plate FS 66 not illustrated 1
17 9022 341 0980 Spline screw IS-M5x16 3
18 4123 149 0600 Muffler gasket 1
19 4123 145 0700 Inlet casing 1
20 9022 341 0980 Spline screw IS-M5x16 2
21 4123 149 0605 Muffler gasket 1
22 1113 141 9000 NLA Screen 1
23 9099 021 2740 Self-tapping screw 3.9x9.5 1
24 4123 140 0800 Exhaust casing 1
25 9022 313 0610 Spline screw IS-M4x6 4
Not numbered on the diagram — assemblies, kits and options
— 4123 190 4000 Rewind starter Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 48 / FS 52 / FS 56 / FS 66

FS 48, FS 52, FS 56, FS 66: counterclockwise starter spring remains distinct

TI01/1994 assigns 0000 998 0609 to these legacy engines, not clockwise spring 0612.

  • The assignment table names FS 48, FS 52, FS 56 and FS 66 for spring 0000 998 0609 and counterclockwise rotation, looking at the carrier. Its separate clockwise row names FS 72, FS 74 and FS 76 with 0000 998 0612.
  • This record is confined to the legacy series4123 starter sheets. The shared FS 62/66 sheet does not add FS 62 to the source roster; later series4144 FS 56 and its ErgoStart variants are not covered by this 1994 assignment. No service cutoff or replacement with 0612 is stated for these four legacy models.
  • Historical English TI01/1994, sections 5–10. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.

Source: TI 1/1994, p. 7 — FS 48, FS 52, FS 56, FS 66: counterclockwise starter spring remains distinct.

Part numbers (1)
  • 0000 998 0609 — Legacy counterclockwise-engine starter torsion springspecified-part · FS 48, FS 52, FS 56, FS 66: counterclockwise starter spring remains distinct

Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85 / BG 72 / FC 72 / FS 48 / FS 52 / FS 56 / FS 62 / FS 66 / FS 72 / FS 74 / FS 76 / HS 72 / HS 74 / HS 76

ElastoStart replacement rope: original-number conflict retained

New 0000 195 8200 is3.0×800 mm; prose and table disagree on the original.

continuously — Continuous introduction; no numeric boundary supplied for this particular change.

  • Section 3 prose prints ORIGINAL 4123 190 4000 (2.7×900 mm), replaced for some time by ELASTOSTART 0000 195 8200 (3.0×800 mm). The summary instead prints ORIGINAL 4123 195 8200. Both are confirmed on the original scan: retain the UNRESOLVED NUMBER CONFLICT, not an OCR correction, proven equivalence or two-step supersession.
  • In addition to cover models, the source explicitly extends this change to BG 72, FC 72, FS 48/52/56/62/66/72/74/76 and HS 72/74/76. These are the historical configurations: not the later type 4144 FS 56 or type 4112 FS 80.
  • Modification introduced CONTINUOUSLY; summary remark says ORIGINAL NO LONGER AVAILABLE FROM FACTORY. No machine-number cutoff, handle assembly replacement, knot procedure or permission to shorten either rope to an unprinted length is given. Catalog associations expose the historical note without rewriting their rope rows or choosing which conflicting original is correct.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 5 — Entire section 3 prose, extended model list, summary and availability remark.

Part numbers (3)
  • 4123 190 4000 — Original rope number printed in prose;2.7×900 mmConflicts with summary original · Only the named TI 41/1997 configurations and conditions
  • 4123 195 8200 — Original rope number printed in summaryConflicts with prose original · Only the named TI 41/1997 configurations and conditions
  • 0000 195 8200 — ElastoStart rope;3.0×800 mmReplacement · Only the named TI 41/1997 configurations and conditions

Wrong number or missing part for the FS 62, FS 66? Report a correction →