Stihl 4126 · Section C · 3 of 14 · 14 parts
Ignition system, Clutch
Fits FS 88.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (14)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4126 400 1201 | Flywheel Fitment / change note → | 1 |
| 2 | 9291 021 0180 | Washer 8.4 | 1 |
| 3 | 9210 260 1100 | Hexagon nut M8 | 1 |
| 4 | 4126 400 1310 | Ignition module Fitment / change note → | 1 |
| 5 | not sold separately | Ignition lead 225 mm not available as a separate item | 1 |
| 6 | 0000 989 1010 | Grommet | 1 |
| 7 | 9022 341 1019 | Spline screw IS-M5x20 | 2 |
| 8 | 4126 160 2001 | Clutch | 1 |
| 9 | 4126 997 1200 | Tension spring | 1 |
| 10 | 4112 162 8902 | Washer | 2 |
| 11 | 4112 162 8903 | Washer | 2 |
| 12 | 4126 162 4200 | Collar screw | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m not illustratedoption | 1 |
| — | 0000 930 2251 | Ignition lead 10 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · FS 88
FS 88: series 4126 replacement ignition assignment
4126 400 1310 with flywheel 4126 400 1201; 225 mm ignition lead.
- Printed series 4126. Use 4126 400 1310 with flywheel 4126 400 1201.
- Printed ignition-lead length: 225 mm (8 7/8 in). Preserve both printed units.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.
Part numbers (2)
- 4126 400 1310 — Replacement ignition moduleAssigned component · FS 88, printed series 4126, listed combination only
- 4126 400 1201 — Assigned flywheelRequired pairing · FS 88, printed series 4126
Service note · FS 88 / FS 108
FS 88 / 108: ignition timing and lead-length conflict
The original prints 200 mm as 8¾ inches; those lengths are not equivalent.
- Electronic ignition comprises flywheel and ignition module with integral trigger unit. Flywheel does NOT need removal to access the module. Air gap 0.1–0.5 mm (0.004–0.020 in).
- At 8000 rpm, timing BEFORE TOP DEAD CENTER: FS 88 1.25–1.75 mm (0.05–0.07 in); FS 108 1.45–2.05 mm (0.06–0.08 in). Do not swap the model-specific ranges or treat them as crankshaft degrees.
- Ignition lead length is printed as 200 mm (8¾ in). SOURCE CONFLICT: 200 mm is about 7.87 in, whereas 8¾ in is 222.25 mm. Neither value is silently corrected or declared verified; confirm the exact replacement configuration before cutting a lead.
- Suppressed plug Bosch WSR 6 F or NGK BPMR 7 A; heat range 200; electrode gap 0.5 mm (0.020 in); M14x1.25 thread, 9.5 mm (0.37 in) thread length. This historical listing is not a cross-brand heat-range conversion rule.
- Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.
Source: TI 37/1994, p. 3 · TI 37/1994, p. 5 — FS 88 / 108: ignition timing and lead-length conflict.
No additional parts-table entry added.
Service note · FS 88 / FS 108
FS 88 / 108: engine and ignition tightening torques
Model-specific clutch and crankcase fasteners must not be interchanged.
- All pairs below are Nm / lbf.ft as printed; fastener identity and component remain part of the specification. No tightening sequence, lubricant or thread-locker condition is supplied by this table.
- Crankcase spline screws: FS 88 IS-M 5x25, FS 108 IS-M 5x30, both 10.5 / 7.7. Cylinder to crankcase IS-M 5x16: 10.0 / 7.4. Clutch shoes: FS 88 flange screw M6 8.0 / 5.9; FS 108 hex-head M8x20 17.0 / 12.5.
- Muffler to cylinder IS-M 5x16 and muffler to crankcase IS-M 5x12: each 10.5 / 7.7. Cover plate to muffler IS-M 4x12: 3.5 / 2.6. Clutch housing IS-M 5x16: 9.5 / 7.0. Flywheel and carrier M8 hexagon nuts: each 17.0 / 12.5.
- Ignition module IS-M 5x20: 7.5 / 5.5. Spark plug M14x1.25: 19.0 / 14.0. Do not apply the FS 108 clutch-shoe torque to FS 88.
- Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.
Source: TI 37/1994, p. 8 — engine and ignition tightening torques.
No additional parts-table entry added.
Wrong number or missing part for the FS 88? Report a correction →