Stihl 4126 · Section E · 5 of 14 · 19 parts
Air filter
Fits FS 88.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (19)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4135 141 0800 | Filter housing | 1 |
| 2 | 9022 341 1220 | Spline screw IS-M5x48 | 2 |
| 3 | 4135 124 2800 | Filter | 1 |
| 4 | 4135 124 1500 | Prefilter | 1 |
| 5 | 4135 141 0500 | Filter cover | 1 |
| 6 | 4135 149 0500 | Gasket | 1 |
| 7 | 4126 120 0610 | Carburetor WT-45A | 1 |
| 7 | 4126 120 0611 NLA | Carburetor WT-367 | 1 |
| 8 | 4222 123 7300 | Lever | 1 |
| 9 | 4135 129 0905 | Gasket | 1 |
| 10 | 9022 341 0980 | Spline screw IS-M5x16 | 1 |
| 11 | 4135 182 7600 | Tensioner | 1 |
| 12 | 9022 313 0680 | Spline screw IS-M4x16 | 1 |
| 13 | 9022 341 1050 | Spline screw IS-M5x25 | 2 |
| 14 | 9291 021 0120 | Washer 5.3 | 2 |
| 15 | 4135 121 1600 | Spacer flange | 1 |
| 16 | 9214 320 0700 | Lock nut M5 | 1 |
| 17 | 4135 129 0900 | Gasket | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4126 007 1051 | Set of gaskets Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 88 / FS 108
FS 88 / 108: filter stack, controls and isolation
Foam sits between the cover and felt; no tool is needed for the filter cover.
- Diaphragm carburetor has a thermally insulated cylinder mounting. Air filter diagram: cover 3, foam element 1, felt element 2 toward the engine. Cover removal/refitting needs no tools. Fuel capacity 0.69 l (1.45 US pt); no mixture ratio or filter-part number printed here.
- Control layout is described as FS 72, 74, 76, 86 and 106: throttle trigger lock 4, trigger 5, slide control 6. Starting-throttle, run and stop positions are selected with one hand. Illustration labels STOP, I and START; no bypass of the trigger lock is authorized.
- Clutch shoes have linings and pivot on the flywheel. AV layout is described as FS 74/76, isolating vibration mainly to the engine. These comparisons do not establish universal control, clutch or AV-rubber interchange.
- Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.
Source: TI 37/1994, p. 1 · TI 37/1994, p. 3 · TI 37/1994, p. 5 — FS 88 / 108: filter stack, controls and isolation.
No additional parts-table entry added.
Service note · FS 88 / FS 108
FS 88 / 108: model-specific repair kits
Carburetor kits and engine gasket sets retain their separate model rosters.
- Carburetor parts kit: FS 86 / FS 88 4117 007 1061; FS 106 / FS 108 4132 007 1061. This does NOT approve either kit for every later carburetor appearing on the shared model catalog. No carburetor model code is printed in this table.
- Gasket set: FS 88 4126 007 1051; FS 108 4135 007 1050. Gasket panel DIN A3 0457 281 2104 is separately listed, not a substitute complete gasket set.
- Dirko sealant 0783 830 2120 is for sealing the crankcase. Lube grease 0781 120 1111, 370 g (13 oz) tube, is for oil seals; package mass is not an installation quantity. No sealant bead dimension or kit contents supplied.
- Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.
Source: TI 37/1994, p. 7 — FS 88 / 108: model-specific repair kits.
Part numbers (7)
- 4117 007 1061 — Carburetor parts kit FS 86 / FS 88historical listed item · FS 88 / 108: model-specific repair kits
- 4132 007 1061 — Carburetor parts kit FS 106 / FS 108historical listed item · FS 88 / 108: model-specific repair kits
- 4126 007 1051 — FS 88 gasket sethistorical listed item · FS 88 / 108: model-specific repair kits
- 4135 007 1050 — FS 108 gasket sethistorical listed item · FS 88 / 108: model-specific repair kits
- 0457 281 2104 — DIN A3 gasket panelhistorical listed item · FS 88 / 108: model-specific repair kits
- 0783 830 2120 — Dirko crankcase sealanthistorical listed item · FS 88 / 108: model-specific repair kits
- 0781 120 1111 — Oil-seal lube grease 370 ghistorical listed item · FS 88 / 108: model-specific repair kits
Service note · FS 88 / FS 108
FS 88 / 108: carburetor and leakage-test values
Basic screw settings are not final running adjustment or a complete leak-test procedure.
- High-speed screw H and low-speed screw L: back off 1 FULL TURN each. Source calls this BASIC SETTING and says screws are initially “hard against their seats”; preserve this historical wording without converting it into a specified tightening torque or a recommendation to force delicate seats. Exact applicable carburetor service procedure remains necessary.
- Full-load engine speed WITHOUT CUTTING TOOL 12000 rpm; idle 2800 rpm. The source wording is retained; these are not permission for unattended running or evidence of safe loaded-tool speed.
- Carburetor leakage test closing pressure 0.8 bar (11.6 psi). Crankcase leakage test at GAUGE PRESSURE 0.5 bar (7.25 psi), and UNDER VACUUM 0.5 bar (7.25 psi magnitude below ambient). Vacuum is not positive 0.5 bar or an absolute pressure specification. No hold time, permitted decay or leak-rate tolerance is printed on page 7; none is invented.
- Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.
Source: TI 37/1994, p. 4 · TI 37/1994, p. 7 — FS 88 / 108: carburetor and leakage-test values.
No additional parts-table entry added.
Service note · FS 88 / FS 108
FS 88 / 108: starter, fuel and cover tightening torques
Two clamp-related rows have no torque specified.
- Pairs are Nm / lbf.ft. Fuel tank flange screw IS-M 5x14: 5.5 / 4.0. Starter cover top IS-M 5x16: 5.5 / 4.0; support/starter cover bottom AND support to clutch housing IS-M 5x16: 7.5 / 5.5. Special rope-rotor spline screw IS-P 5.5x12: 2.5 / 1.8.
- Carburetor IS-M 5x22: 5.5 / 4.0. Spacer flange to cylinder IS-M 5x25: 5.5 / 4.0. Shroud IS-M 5x12: 5.5 / 4.0.
- Adjusting screw in clamp IS-M 4x25 and clamp to spacer flange IS-M 5x16 each have a DASH, not a zero or a specified torque. Do not fill these explicitly unspecified rows with the generic M4/M5 values. Exact service instructions are needed.
- Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.
Source: TI 37/1994, p. 8 — starter, fuel and cover tightening torques.
No additional parts-table entry added.
Service note · FS 88 / FS 108
FS 88 / 108: repair manual and carburetor chapter routing
FS 88 / 108 manual omits carburetor servicing; FS 86 / 106 chapter was the interim reference.
- All repair procedures are referred to the STIHL FS 88 / 108 service manual. Section 8 says that this new manual, for the first time, omits the chapter “Servicing the Carburetor”. A separate carburetor servicing/repair handbook was expected in the foreseeable future as of the bulletin date, not verified as available here.
- Until that handbook was published, the carburetor chapter in the FS 86 / 106 manual could be used as a reference. This does not make all FS 86/106 parts or settings interchangeable with every FS 88/108 carburetor variant. This TI review does not claim those manuals have been imported or accepted; whole-manual inventory/acceptance is the separate follow-on phase.
- Section 7 requires strict observance of local/national safety regulations AND the owner’s-manual precautions if a unit is started during repairs or maintenance. A repair-time entry marked for a test run is not authorization for unattended running. Bulletin footer: Waiblingen, December 14, 1994; D1/MTK-na; Andreas Stihl Technical Documentation. Footer and cut-out outline are provenance/layout, not serial applicability.
- Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.
Source: TI 37/1994, p. 11 · TI 37/1994, p. 12 — repair manual and carburetor chapter routing.
No additional parts-table entry added.
Service note · FS 88 / FS 108
FS 88 / 108: engine repair times and loaded-test footnote
Minutes assume trained personnel in a properly equipped workshop; one row has no time.
- The single FS 88 / FS 108 column gives MINUTES for trained personnel in a properly equipped service workshop, not guaranteed elapsed time or labor pricing. This table may be added to the STIHL repair-times table. Asterisks mean TEST RUN UNDER LOAD, not a different unit or extra minutes.
- Rows 1–4: remove/refit engine 10; crankcase, pressure test* 100; crankshaft/bearings, pressure test* 100; sealing rings, pressure test* 60. Rows 5–8: crankcase leakage test, test run 30; cylinder/piston, pressure test* 45; ignition system* 15; fuel supply/tank vent, test run 10.
- Row 9 manifold or flange, pressure test: DASH, no time specified; not zero and not inferred from adjacent rows. Row 10 carburetor check* 25. The starred rows here are 2, 3, 4, 6, 7 and 10. Unstarred rows explicitly saying test run do not acquire an unprinted under-load requirement from this footnote.
- Times are not a complete pressure-test, running or repair procedure. No extra minutes should be inferred by adding a second test run to a row whose named procedure already includes one.
- Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.
Source: TI 37/1994, p. 12 — engine repair times and loaded-test footnote.
No additional parts-table entry added.
Wrong number or missing part for the FS 88? Report a correction →