Stihl 4130 · Section E · 5 of 14 · 35 parts
Carburetor WT-492A (USA)
Fits FS 36, FS 40, FS 44.
Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.
Parts (35)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1114 121 7800 | Strainer | 1 |
| 2 | 1121 121 4801 | Pump diaphragm | 1 |
| 3 | 1120 129 0905 | Gasket | 1 |
| 4 | 4116 121 5100 | Inlet needle | 1 |
| 5 | 1120 122 3001 | Spring | 1 |
| 6 | 4117 122 9402 | Plug | 1 |
| 7 | 1120 129 0900 | Gasket | 1 |
| 8 | 1113 121 4705 | Metering diaphragm | 1 |
| 9 | 4126 121 0800 | End cover | 1 |
| 10 | 1114 122 7100 | Screw | 1 |
| 11 | 4117 122 3006 | Spring | 1 |
| 12 | 4117 122 6200 | Idle speed adjustment screw | 1 |
| 13 | 1113 121 5000 | Inlet control lever | 1 |
| 14 | 1113 121 9200 | Spindle | 1 |
| 15 | 1114 122 7400 | Round head screw | 1 |
| 16 | 4130 121 5400 | Valve jet | 1 |
| 18 | 1113 121 0800 | End cover | 1 |
| 19 | 1106 122 7400 | Round head screw | 4 |
| 21 | 4130 120 7101 | Throttle shaft with lever | 1 |
| 22 | 1117 122 9000 | E-clip | 1 |
| 23 | 4130 121 3300 | Throttle shutter | 1 |
| 24 | 1110 122 7400 | Round head screw | 2 |
| 25 | 1116 122 3000 | Spring | 1 |
| 26 | 1116 122 4200 | Ball | 1 |
| 27 | 4130 121 3000 | Choke shaft | 1 |
| 28 | 4130 121 2900 | Choke shutter | 1 |
| 30 | 4203 122 6803 | Low speed adjustment screw Fitment / change note → | 1 |
| 31 | 4130 122 6702 | High speed adjustment screw | 1 |
| 32 | 4203 121 2700 | Cap Fitment / change note → | 2 |
| 33 | 4130 121 8600 | Washer | 1 |
| 34 | 4130 120 8700 | Control valve | 1 |
| 35 | 4130 122 3905 | Connector | 1 |
| 36 | 5910 890 4500 | Puller Fitment / change note → option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4130 120 0603 | Carburetor WT-492A Fitment / change note → | 1 |
| — | 4130 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 36 / FS 40 / FS 44 / FC 44
FS 36 / FS 40 / FS 44 / FC 44: WT492 components
The same WT492 assembly is listed for brushcutters and the edger; settings still differ.
- Page 1 assigns WT492 to FS 36, FS 40, FS 44 and FC 44. Page 3 item 3 is carburetor 4130 120 0603 and includes items 6 through 9: high-speed screw 4203 122 6702, low-speed screw 4203 122 6803, two limiter caps 4203 121 2700 and two sealing rings 4203 122 3600. Shared parts do NOT transfer the brushcutter full-load procedure to FC 44.
- Introduction is IN PROGRESS. No serial cutoff, old assembly number, universal retrofit approval or present stock status is supplied. The page 1 drawing numbers 1–4 identify component functions; they are NOT the page 3 spare-parts item numbers.
- Historical TI11/1997 evidence for the named carburetor versions only, not every carburetor on these models. Later IPL sheet labels HD-13B and WT-492A are discovery context, not proof of unchanged calibration. The shared BR sheets also name other variants; this note does not extend its model list to them. No hardware operation was performed.
Source: TI 11/1997, p. 1 · TI 11/1997, p. 3 — FS 36 / FS 40 / FS 44 / FC 44: WT492 components.
Part numbers (5)
- 4130 120 0603 — Carburetor WT492, item 3New assembly · FS 36/FS 40/FS 44/FC 44; FS 36 / FS 40 / FS 44 / FC 44: WT492 components
- 4203 122 6702 — High-speed screw, item 6WT492 component · FS 36/FS 40/FS 44/FC 44; FS 36 / FS 40 / FS 44 / FC 44: WT492 components
- 4203 122 6803 — Low-speed screw, item 7WT492 component · FS 36/FS 40/FS 44/FC 44; FS 36 / FS 40 / FS 44 / FC 44: WT492 components
- 4203 121 2700 — Limiter cap; two per carburetorShared new component · FS 36/FS 40/FS 44/FC 44; FS 36 / FS 40 / FS 44 / FC 44: WT492 components
- 4203 122 3600 — Sealing ring; two per carburetorShared new component · FS 36/FS 40/FS 44/FC 44; FS 36 / FS 40 / FS 44 / FC 44: WT492 components
Service note · BR 320 / BR 320 L / BR 400 / FS 36 / FS 40 / FS 44 / FC 44
BR / FS / FC: identical limiter caps, sealing rings and left-hand puller
90-degree range, single-use caps and flush installation remain explicit.
- The new high- and low-speed limiter caps are identical. A separate sealing ring on each adjusting screw seals against the carburetor body and helps prevent air leakage through its threads. Screw knurling locks the pressed-in caps, which sit flush with the body. No ring dimensions or torque are specified.
- Each mounting hole has a quadrant stop; each cap has a molded tang. Together they limit adjustment to 90 degrees, at most 1/4 turn. Page 2 presents this as allowing a leaner mixture at higher altitude without enriching beyond the stated CARB/EPA limits. This is a dated design/regulatory statement, not current compliance certification.
- For correction of the basic setting in the service shop, the source specifies puller 5910 890 4500 for BOTH L and H caps. It has a LEFT-HAND thread and screws into a cap COUNTERCLOCKWISE. The molded tang meets the stop; the puller presses against the screw head and eases the cap out. Do not reinterpret the rotation as a right-hand thread.
- Caps removed once MUST NOT be reused. Section 1.4.6 requires NEW caps pushed into the screw holes until flush with the carburetor body. The subsequent running-behavior check is mandatory in the flow chart. Page 3 item 10 is the puller; it is NOT included in carburetor item ranges 4/5/8/9 or 6–9.
- Historical TI11/1997 evidence for the named carburetor versions only, not every carburetor on these models. Later IPL sheet labels HD-13B and WT-492A are discovery context, not proof of unchanged calibration. The shared BR sheets also name other variants; this note does not extend its model list to them. No hardware operation was performed.
Source: TI 11/1997, p. 1 · TI 11/1997, p. 2 · TI 11/1997, p. 3 · TI 11/1997, p. 7 — BR / FS / FC: identical limiter caps, sealing rings and left-hand puller.
Part numbers (3)
- 4203 121 2700 — Limiter cap; two per carburetorShared new component · BR 320/BR 320 L/BR 400/FS 36/FS 40/FS 44/FC 44; BR / FS / FC: identical limiter caps, sealing rings and left-hand puller
- 4203 122 3600 — Sealing ring; two per carburetorShared new component · BR 320/BR 320 L/BR 400/FS 36/FS 40/FS 44/FC 44; BR / FS / FC: identical limiter caps, sealing rings and left-hand puller
- 5910 890 4500 — Left-hand-thread limiter-cap puller, item 10Service tool; not included in carburetor · BR 320/BR 320 L/BR 400/FS 36/FS 40/FS 44/FC 44; BR / FS / FC: identical limiter caps, sealing rings and left-hand puller
Service note · BR 320 / BR 320 L / BR 400 / FS 36 / FS 40 / FS 44 / FC 44
BR / FS / FC: preparation and both running-behavior checks
The flow chart returns BOTH failed checks to idle adjustment, not directly to completion.
- Page 4 sequence: preparations (1.4.1), basic setting (1.4.2), idle adjustment (1.4.3), full-load adjustment (1.4.4), running-behavior check (1.4.5), NEW limiter-cap installation (1.4.6), then a SECOND running-behavior check. A NO at EITHER check returns to IDLE adjustment, then full-load adjustment; only the final YES ends the procedure. The return arrows are visible in the original, not recoverable from flattened OCR alone.
- Engine speeds MUST be checked with a tachometer. Inspect and, if needed, clean the air filter; inspect the spark-arresting screen and clean or replace it as needed. On blowers mount the blower tubes AND nozzle. On brushcutters mount a STIHL Autocut or Polymatic head and initially set the lines to the limiting blade on the deflector. The later full-load line-length instruction is retained separately.
- SOURCE SCOPE ANOMALY: preparations also say to clean and oil hedge-trimmer blades, but NO hedge trimmer is named on the cover or in either settings table. This sentence is preserved without inventing HS-model applicability or settings. No specific edger preparation is printed here; do not substitute a mowing head on FC 44.
- The running-behavior check opens the throttle several times to verify smooth acceleration; the engine must also idle smoothly. If a check after cap installation requires removal, the no-reuse rule still applies. These are historical service instructions, not a report that a machine was adjusted.
- Historical TI11/1997 evidence for the named carburetor versions only, not every carburetor on these models. Later IPL sheet labels HD-13B and WT-492A are discovery context, not proof of unchanged calibration. The shared BR sheets also name other variants; this note does not extend its model list to them. No hardware operation was performed.
Source: TI 11/1997, p. 4 · TI 11/1997, p. 5 · TI 11/1997, p. 7 — BR / FS / FC: preparation and both running-behavior checks.
No additional parts-table entry added.
Service note · FS 36 / FS 40 / FS 44
FS 36 / FS 40 / FS 44: WT492 mowing-head adjustment
L/H = 1.5/4 turns; loaded setup range 6,500–8,500 rpm before the approximate 100 rpm drop.
- WT492 basic settings: L = 1.5 turns and H = 4 turns open, for each of FS 36, FS 40 and FS 44.
- Basic opening is measured from screws LIGHTLY seated. After the basic setting the source starts the engine. Idle procedure: find maximum idle speed with L, then turn L counterclockwise until speed drops ABOUT 300 rpm; use the SEPARATE idle-speed screw LA to set 3,100 rpm. The 300 rpm drop is not itself the final idle target. Tachometer, filter/screen checks, equipment preparation and BOTH running-behavior checks apply.
- The full-load procedure requires BOTH mowing head AND deflector mounted. At full throttle, carefully turn H clockwise until no further speed increase is obtained WITHIN 6,500–8,500 rpm. If the required range is not reached, the source varies the cutting-line length until the speed is correct. Then turn H counterclockwise until speed drops ABOUT 100 rpm. The range is a setup condition under the stated load, not a universal unloaded speed limit or metal-blade setting.
- The initial preparation uses Autocut or Polymatic lines reaching the deflector limiting blade. The subsequent instruction to vary line length is preserved as a separate source step; no alternative numeric line length is invented. FC 44 uses a different full-load sequence despite sharing WT492.
- Historical TI11/1997 evidence for the named carburetor versions only, not every carburetor on these models. Later IPL sheet labels HD-13B and WT-492A are discovery context, not proof of unchanged calibration. The shared BR sheets also name other variants; this note does not extend its model list to them. No hardware operation was performed.
Source: TI 11/1997, p. 1 · TI 11/1997, p. 4 · TI 11/1997, p. 5 · TI 11/1997, p. 6 · TI 11/1997, p. 7 — FS 36 / FS 40 / FS 44: WT492 mowing-head adjustment.
No additional parts-table entry added.
Service note · BR 320 / BR 320 L / BR 400 / FS 36 / FS 40 / FS 44 / FC 44
BR / FS / FC: 50:1 approval statement and bounded reference gaps
Exact user-instruction and California warranty references are unavailable in the verified local pools.
- TI11/1997 states emissions approval was obtained with a 50:1 fuel-oil mix and that no emissions measurements are available for other mix ratios. It does not establish approval for other ratios, a present-day legal status, a lubricant grade or a fuel specification beyond this ratio.
- Section 2 says the user setting instructions are exactly those in the owner’s manual chapter Adjusting the Carburetor, but does not reproduce that chapter or identify its edition. Sections 3 and 4 refer to TI41/1994 and TI47/1994 for fuel context and the California Emission Control Warranty Statement. Neither TI nor the exact owner-manual chapters/editions was found in the verified local pools: 690 retained TIs, 766 resource PDFs, 41 owner-collected service PDFs and document metadata/model associations. These are THREE bounded source dependencies, not proof that the documents do not exist elsewhere.
- Exact catalog products 49 (BR 320/320 L/400), 68 (FC 44) and 101 (FS 36/40/44) have no linked manual. A same-name later FS 40 group, product 447, links SERIES 4144 workshop documents, not the SERIES 4130 owner chapter named here. The generic Manuals category contains special-tools and chain/bar manuals only. No later FS 40 procedure or unverified warranty text is substituted.
- The last-TI list (BR 320/400:14/1996; FS 36/40/44:19/1996; FC 44:07/1996) is bibliographic context, not an additional fitment or calibration claim. The original repeats section number 1.3 for Adjustment and New spare parts; citations use page and title to avoid ambiguity.
- Historical TI11/1997 evidence for the named carburetor versions only, not every carburetor on these models. Later IPL sheet labels HD-13B and WT-492A are discovery context, not proof of unchanged calibration. The shared BR sheets also name other variants; this note does not extend its model list to them. No hardware operation was performed.
Source: TI 11/1997, p. 7 — BR / FS / FC: 50:1 approval statement and bounded reference gaps.
No additional parts-table entry added.
Wrong number or missing part for the FS 36, FS 40, FS 44? Report a correction →