Stihl 4133 · Section C · 3 of 7 · 30 parts
Air filter, Fuel tank
Fits BG 72.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (30)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4227 129 0901 | Gasket Fitment / change note → | 1 |
| 2 | 9007 319 1121 | Hexagon head screw M5x56 Fitment / change note → | 2 |
| 3 | 4133 121 1602 | Spacer flange Fitment / change note → | 1 |
| 4 | 9022 341 1050 | Spline screw IS-M5x25 | 2 |
| 5 | 4114 129 0501 | Gasket | 1 |
| 6 | 4227 120 0600 | Carburetor WT-253 | 1 |
| 6 | 4227 120 0601 | Carburetor WT-330 | 1 |
| 7 | 4227 122 1800 | Heat shield | 1 |
| 8 | 4114 149 1205 | Gasket | 1 |
| 9 | 4133 140 2800 | Filter housing | 1 |
| 10 | 9210 261 0700 | Hexagon nut M5 Fitment / change note → | 2 |
| 11 | 4133 124 2800 | Filter | 1 |
| 12 | 4133 124 1500 | Prefilter | 1 |
| 13 | 4133 141 0500 | Filter cover | 1 |
| 14 | 4227 350 0400 | Fuel tank | 1 |
| 15 | 4227 358 0800 | Hose 185 mm / 7 5/16'' | 1 |
| 16 | 4227 358 0805 | Hose 235 mm / 9 1/4'' | 1 |
| 17 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 2 |
| 18 | 9307 021 0120 | Washer 5.3 | 2 |
| 19 | 0000 350 3502 | Pickup body | 1 |
| 20 | 4128 350 0505 | Filler cap | 1 |
| 21 | 0000 350 0900 | Rope | 1 |
| 22 | 0000 353 0800 | Filler cap retainer | 1 |
| 23 | 4133 122 6900 | Plug Fitment / change note → | 2 |
| 24 | 9291 021 0120 | Washer 5.3 | 2 |
| 40 | 4126 350 5801 | Tank vent | 1 |
| 41 | 4126 359 0700 | Gasket | 1 |
| 42 | 4117 358 9300 | Strainer | 1 |
| 43 | 4117 358 8001 | Ring | 1 |
| 44 | 4117 358 1800 | Filter | 2 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · BG 72
BG 72: uprated engine needs all new parts
From X 31 409 901; approximately 8% more power to 0.7 kW / 0.95 bhp requires the complete upgrade.
X 31 409 901 — Printed BG 72 uprated-engine introduction; not a series-wide production or successor cutoff.
- FROM X 31 409 901, engine power increases approximately 8% to 0.7 kW (0.95 bhp). Changes: different port timing, higher compression ratio, enlarged inlet port, modified transfer ports, modified gasket and spacer flange. No numerical port timing or compression ratio is provided.
- Factory supply describes new cylinder, gasket and spacer flange as universal replacement parts within this BG 72 instruction. ONLY NEW versions may repair NEW machine versions, otherwise loss of power and running problems may occur. Increasing an OLD machine to approximately 0.7 kW is possible ONLY IF ALL NEW PARTS ARE INSTALLED; a cylinder or gasket alone is not the stated upgrade.
- Mandatory companion hardware remains part of the upgrade: M5 x 20 cylinder screws at 10 Nm (7.5 lbf.ft), M5 x 56 intake screws and plugs, M5 x 25 flange screws and A 5.3 washers. The 10 Nm torque belongs to the cylinder screws, not every intake fastener.
- The footer is June 19, 1995, with copyright 1995. Last TI28.92 is a prior-bulletin pointer, not a missing prerequisite for this self-contained instruction.
- TI03/1995 prints BG 72, series 4227; retained exact-model BG 72 sheets are cataloged under 4133. Links are model-label navigation, not proof of series equivalence or applicability to BG 75, HS machines or other models. Verify the actual configuration.
- Historical TI03/1995 guidance only. Factory supply and power claims are historical, not current stock or measured results. No hardware operation was performed.
Source: TI 3/1995, p. 1 · TI 3/1995, p. 2 · TI 3/1995, p. 3 — BG 72: uprated engine needs all new parts.
No additional parts-table entry added.
Service note · BG 72
BG 72: enlarged inlet gasket window
4227 129 0901 replaces 4227 129 0900; 19 mm window replaces 16 mm.
X 31 409 901 — Printed BG 72 uprated-engine introduction; not a series-wide production or successor cutoff.
- Illustration 325TI002 shows original 16 mm (0.63 in) and new 19 mm (0.75 in) inlet windows. New gasket 4227 129 0901 MAY be installed in older machines, but the full 0.7 kW upgrade still requires all new parts. New engines may be repaired only with new versions.
- Original gasket 4227 129 0900 is supplied only until existing factory stocks are exhausted. Retained BG 72 intake sheet C agrees on new gasket 4227 129 0901. This does not substitute HS-series gasket numbers or establish interchange across models.
- TI03/1995 prints BG 72, series 4227; retained exact-model BG 72 sheets are cataloged under 4133. Links are model-label navigation, not proof of series equivalence or applicability to BG 75, HS machines or other models. Verify the actual configuration.
- Historical TI03/1995 guidance only. Factory supply and power claims are historical, not current stock or measured results. No hardware operation was performed.
Source: TI 3/1995, p. 2 · TI 3/1995, p. 3 — BG 72: enlarged inlet gasket window.
Part numbers (2)
- 4227 129 0900 — Inlet gasket; 16 mm windoworiginal; stocks only · BG 72; TI03/1995 conditions
- 4227 129 0901 — Inlet gasket; 19 mm windownew; permitted on older machines · BG 72; TI03/1995 conditions
Service note · BG 72
BG 72: spacer-flange retrofit needs matching intake hardware
19 mm cylinder-side opening; M5 x 56 screws/plugs plus M5 x 25 screws/A 5.3 washers are mandatory.
X 31 409 901 — Printed BG 72 uprated-engine introduction; not a series-wide production or successor cutoff.
- New spacer flange has a 19 mm (0.75 in) cylinder-side opening. When fitted to older machines, check the filter base / carburetor / flange / cylinder assembly. M5 x 56 screws and plugs 4133 122 6900 MUST be used. Mount flange to cylinder using M5 x 25 screws and A 5.3 washers. This TI supplies no full order numbers or tightening torque for the flange screws/washers; do not assign the cylinder’s 10 Nm torque to them.
- Illustration 325TI001 page 2 keys: 1 = M5 x 56 screws, 2 = plugs, 3 = M5 x 25 screws, 4 = A 5.3 washers. These are NOT page 3 table keys: 3 = flange, 4 = M5 x 56 screws, 5 = M5 nuts, 6 = plugs.
- Original complete spacer flange 4133 120 2202 includes table items 3–6 and is no longer factory-available. Its new column is a dash, not a new complete assembly number. New separate flange (item 3) is 4133 121 1602; original separate flange is -*- with no order number. Do not claim that the new separate flange includes all former assembly contents.
- Unchanged companion numbers: 9007 319 1121 screws (2x), 9210 261 0700 M5 hexagon nuts (2x), 4133 122 6900 plugs (2x). These are installed counts; no MOQ column appears. Source calls 9007 319 1121 “Spline screw IS-M5 x 56”; retained BG 72 sheet C calls it “Hexagon head screw M5x56”. Preserve the description discrepancy without selecting a winner. The BG 72 IPL agrees on TWO plugs; no plug-count conflict is inferred from a different model.
- TI03/1995 prints BG 72, series 4227; retained exact-model BG 72 sheets are cataloged under 4133. Links are model-label navigation, not proof of series equivalence or applicability to BG 75, HS machines or other models. Verify the actual configuration.
- Historical TI03/1995 guidance only. Factory supply and power claims are historical, not current stock or measured results. No hardware operation was performed.
Source: TI 3/1995, p. 2 · TI 3/1995, p. 3 — BG 72: spacer-flange retrofit needs matching intake hardware.
Part numbers (5)
- 4133 120 2202 — Complete spacer flangeoriginal; items3–6; unavailable · BG 72; TI03/1995 conditions
- 4133 121 1602 — Separate spacer flangenew; 19 mm opening · BG 72; TI03/1995 conditions
- 9007 319 1121 — M5 x56 screw; source says IS splineunchanged; two · BG 72; TI03/1995 conditions
- 9210 261 0700 — Hexagon nut M5unchanged; two · BG 72; TI03/1995 conditions
- 4133 122 6900 — Plugunchanged; two · BG 72; TI03/1995 conditions
Wrong number or missing part for the BG 72? Report a correction →