Stihl 4134 · Section A · 1 of 18 · 21 parts
Crankcase, Cylinder FS 120, 120 R
Fits FS 120.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (21)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4134 020 2600 | Crankcase | 1 |
| 2 | 0000 988 8600 | Sleeve | 4 |
| 3 | 9503 003 0242 | Grooved ball bearing 6201 | 1 |
| 4 | 4134 020 2900 | Crankcase | 1 |
| 5 | 9640 003 1195 | Oil seal 12x22x5 Fitment / change note → | 2 |
| 6 | 4134 030 0403 | Crankshaft | 1 |
| 7 | 4140 036 0300 | Washer Fitment / change note → | 2 |
| 8 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 Fitment / change note → | 4 |
| 9 | 9075 478 4175 | Pan head self-tapping screw IS-D5x28 Fitment / change note → | 4 |
| 10 | 4134 029 2300 | Cylinder gasket | 1 |
| 11 | 9512 003 2250 | Needle cage 10x13x12.5 | 1 |
| 12 | 4134 020 1213 | Cylinder with piston Ø 35 mm | 1 |
| 13 | 4134 030 2011 | Piston Ø 35 mm | 1 |
| 14 | 4119 034 3001 | Piston ring Ø 35x1.5 mm | 2 |
| 15 | 4119 034 1500 | Piston pin 10x6.5x28 | 1 |
| 16 | 9463 650 1000 | Snap ring 10 | 2 |
| 17 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 17 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 18 | 4134 149 0600 | Muffler gasket | 1 |
| 19 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4134 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI09: narrower crankshaft oil seals retrofit older machines
The 12x22x5 seal replaces the 12x22x7 seal; no installation-depth value is invented.
- To facilitate installation, 7 mm wide oil seal 9640 003 1200 (DIN3760-BS12x22x7) is replaced by 5 mm wide seal 9640 003 1195 (DIN3760-BS12x22x5). The diameter pair remains 12 x 22 mm; the changed dimension is width.
- The new seals may also be used in older machines and are installed in the same way as before. The diagram shows their crankshaft locations but supplies no numerical seating depth or alternate installation method.
- Introduction is in progress; the previous seal is no longer available from the factory. No serial cutoff is stated here, and the preceding clutch USA serial must not be applied to these seals.
- Only the printed TI09/2003 models and described configurations are covered. Shared catalog sheets do not extend this assertion to FS 300, BT 121, SP 200, HT 250 or unlisted R variants. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 21 · TI 9/2003, p. 22 — 6 oil seals and summary.
Part numbers (2)
- 9640 003 1200 — Oil seal12x22x7Previous; discontinued factory supply · TI09/2003 section 6 oil seals and summary models/configurations only; preserve restrictions above
- 9640 003 1195 — Oil seal12x22x5New; older-machine use allowed · TI09/2003 section 6 oil seals and summary models/configurations only; preserve restrictions above
Conditional replacement · FS 120 / FS 200 / FS 250 / BT 120
TI09: three-part and five-part crankshaft washer rules
Remove washers for the three-part spare crankshaft; use two new washers with a reinstalled five-part crankshaft.
- Section7 expressly covers FS 120, FS 200, FS 250 and BT 120 only; FS 350 is excluded. The bulletin cover says BT 120 C while this section prints BT 120. Preserve that naming difference: no exact BT 120 C crankshaft binding or unqualified alias is inferred.
- The three-part crankshaft 4134 030 0400 was replaced in production by a five-part version some time earlier. The five-part version uses washers on either side of the crank web. No five-part crankshaft order number is supplied here.
- The replacement spare is the three-part crankshaft 4134 030 0400 and must be installed WITHOUT washers 4140 036 0300. Remove any such washers remaining in the crankcase before fitting it. Production construction and spare construction are not interchangeable assumptions.
- If reinstalling a five-part crankshaft after crankcase repair, fit two NEW washers 4140 036 0300 total, one on each side of the crank web. The summary specifies quantity2; the prose on either side does not mean four washers. Introduction in progress supplies no serial or date cutoff.
- Only the printed TI09/2003 models and described configurations are covered. Shared catalog sheets do not extend this assertion to FS 300, BT 121, SP 200, HT 250 or unlisted R variants. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 22 — 7 crankshaft, model restriction, diagram and summary.
Part numbers (2)
- 4134 030 0400 — Three-part crankshaftReplacement spare; install without washers · TI09/2003 section 7 crankshaft, model restriction, diagram and summary models/configurations only; preserve restrictions above
- 4140 036 0300 — Crank-web washersTwo new with five-part crankshaft; omit/remove with three-part · TI09/2003 section 7 crankshaft, model restriction, diagram and summary models/configurations only; preserve restrictions above
Conditional replacement · FS 120 / FS 200
FS 120/200: longer cylinder screws and 10 Nm repair torque
Four DG 5x28 screws replace DG 5x24 from serial 2 46 616 989.
2 46 616 989 — From this serial for the stated component change and named model(s) only; not a whole-model production range.
- Four IS DG 5x24 spline screws 9075 478 4159 are replaced by four IS DG 5x28 screws 9075 478 4175 from serial 2 46 616 989.
- The longer screws should also be installed routinely during repairs to older FS 120/200 machines, at tightening torque 10 Nm. This torque belongs to these cylinder screws, not carburetor nuts, collar studs or all screws sharing an order number. Previous screws remain as spares for other components.
- Only the named source models and stated configuration are covered; shared catalog sheets do not extend this note to unnamed models or R variants. Factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 21/2000, p. 1 — 2 Cylinder mounting screws, service note and summary.
Part numbers (2)
- 9075 478 4159 — IS DG 5x24 cylinder screwPrevious; four, retained for other components · FS 120, FS 200; stated source configuration only
- 9075 478 4175 — IS DG 5x28 cylinder screwReplacement; four, 10 Nm · FS 120, FS 200; stated source configuration only
Service note · FS 120 / FS 200 / FS 350 / FS 400 / FS 450
FS120/200/350/400/450: four-port engine specifications
FS200 and FS350 share the printed column; all strokes are32 mm.
- New single-cylinder two-stroke engine uses FOUR-PORT technology. Better mixture control, clean combustion and lower emissions are source claims without measured values here. Decompression valve is specified ONLY FOR FS350/400/450, not FS120/200.
- Engine table: FS120 =30.8 cc (1.88 ci),35 mm (1.37 in) bore,1.3 kW (1.8 bhp). SHARED FS200/FS350 column =36.3 cc (2.21 ci),38 mm (1.49 in) bore,1.6 kW (2.2 bhp). FS400 =40.2 cc (2.45 ci),40 mm (1.57 in),1.9 kW (2.6 bhp). FS450 =44.3 cc (2.70 ci),42 mm (1.65 in),2.1 kW (2.8 bhp). Power is to ISO8893.
- ALL four columns specify32 mm (1.26 in) stroke. Rewind starter is SINGLE PAWL with ElastoStart grip. Easy-start description also specifies manual fuel primer and the model-limited decompression valve. Starter-rope entry delegates to section4; the reviewed ElastoStart note resolves it as grip-with-rope0000 190 3400 and separate rope0000 195 8200, without inferred dimensions.
- These are1997 engine specifications; shared catalog sheets also naming FS250/300/480 do not extend these values to those models.
- Historical TI42/1997 configurations only, not all later versions sharing a model name. No hardware operation was performed. No part interchange or numeric serial cutoff is established.
Source: TI 42/1997, p. 2 · TI 42/1997, p. 3 · TI 42/1997, p. 6 — Section1 powerhead/cylinder/easy-start; section2.1.1 complete engine table; section4 starter-rope cross-reference.
No additional parts-table entry added.
Wrong number or missing part for the FS 120? Report a correction →