← Augers/Drills & other equipment · series 4134

Stihl 4134 · Section C · 3 of 18 · 21 parts

Crankcase, Cylinder FS 250, 250 R

Fits FS 250.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181923345567789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (21)

PosPart numberDescriptionQty
1 4134 020 2600 Crankcase 1
2 0000 988 8600 Sleeve 4
3 9503 003 0242 Grooved ball bearing 6201 1
4 4134 020 2900 Crankcase 1
5 9640 003 1195 Oil seal 12x22x5 Fitment / change note → 2
6 4134 030 0403 Crankshaft 1
7 4140 036 0300 Washer Fitment / change note → 2
8 9075 478 4159 Pan head self-tapping screw IS-D5x24 4
9 9075 478 4175 Pan head self-tapping screw IS-D5x28 4
10 4134 029 2300 Cylinder gasket 1
11 9512 003 2250 Needle cage 10x13x12.5 1
12 4134 020 1214 Cylinder with piston Ø 40 mm 1
13 4134 030 2003 Piston Ø 40 mm 1
14 4119 034 3003 Piston ring Ø 40x1.5 mm 2
15 4119 034 1500 Piston pin 10x6.5x28 1
16 9463 650 1000 Snap ring 10 2
17 0000 400 7000 Spark plug NGK BPMR7A 1
17 1110 400 7005 Spark plug Bosch WSR 6 F 1
18 4134 149 0600 Muffler gasket 1
19 0783 830 2000 Tube of sealant Dirko HT red option 1
Not numbered on the diagram — assemblies, kits and options
— 4134 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350

TI09: narrower crankshaft oil seals retrofit older machines

The 12x22x5 seal replaces the 12x22x7 seal; no installation-depth value is invented.

  • To facilitate installation, 7 mm wide oil seal 9640 003 1200 (DIN3760-BS12x22x7) is replaced by 5 mm wide seal 9640 003 1195 (DIN3760-BS12x22x5). The diameter pair remains 12 x 22 mm; the changed dimension is width.
  • The new seals may also be used in older machines and are installed in the same way as before. The diagram shows their crankshaft locations but supplies no numerical seating depth or alternate installation method.
  • Introduction is in progress; the previous seal is no longer available from the factory. No serial cutoff is stated here, and the preceding clutch USA serial must not be applied to these seals.
  • Only the printed TI09/2003 models and described configurations are covered. Shared catalog sheets do not extend this assertion to FS 300, BT 121, SP 200, HT 250 or unlisted R variants. No physical interchange test was performed.

Source: TI 9/2003, p. 1 · TI 9/2003, p. 21 · TI 9/2003, p. 22 — 6 oil seals and summary.

Part numbers (2)
  • 9640 003 1200 — Oil seal12x22x7Previous; discontinued factory supply · TI09/2003 section 6 oil seals and summary models/configurations only; preserve restrictions above
  • 9640 003 1195 — Oil seal12x22x5New; older-machine use allowed · TI09/2003 section 6 oil seals and summary models/configurations only; preserve restrictions above

Conditional replacement · FS 120 / FS 200 / FS 250 / BT 120

TI09: three-part and five-part crankshaft washer rules

Remove washers for the three-part spare crankshaft; use two new washers with a reinstalled five-part crankshaft.

  • Section7 expressly covers FS 120, FS 200, FS 250 and BT 120 only; FS 350 is excluded. The bulletin cover says BT 120 C while this section prints BT 120. Preserve that naming difference: no exact BT 120 C crankshaft binding or unqualified alias is inferred.
  • The three-part crankshaft 4134 030 0400 was replaced in production by a five-part version some time earlier. The five-part version uses washers on either side of the crank web. No five-part crankshaft order number is supplied here.
  • The replacement spare is the three-part crankshaft 4134 030 0400 and must be installed WITHOUT washers 4140 036 0300. Remove any such washers remaining in the crankcase before fitting it. Production construction and spare construction are not interchangeable assumptions.
  • If reinstalling a five-part crankshaft after crankcase repair, fit two NEW washers 4140 036 0300 total, one on each side of the crank web. The summary specifies quantity2; the prose on either side does not mean four washers. Introduction in progress supplies no serial or date cutoff.
  • Only the printed TI09/2003 models and described configurations are covered. Shared catalog sheets do not extend this assertion to FS 300, BT 121, SP 200, HT 250 or unlisted R variants. No physical interchange test was performed.

Source: TI 9/2003, p. 1 · TI 9/2003, p. 22 — 7 crankshaft, model restriction, diagram and summary.

Part numbers (2)
  • 4134 030 0400 — Three-part crankshaftReplacement spare; install without washers · TI09/2003 section 7 crankshaft, model restriction, diagram and summary models/configurations only; preserve restrictions above
  • 4140 036 0300 — Crank-web washersTwo new with five-part crankshaft; omit/remove with three-part · TI09/2003 section 7 crankshaft, model restriction, diagram and summary models/configurations only; preserve restrictions above

Wrong number or missing part for the FS 250? Report a correction →