Stihl 4134 · Section A · 1 of 14 · 27 parts
Crankcase, Cylinder
Fits FS 300, FS 350.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
This drawing carries 3 bore sizes — Ø 35 mm (also listed for the BT 120 C, BT 121, FS 120), Ø 38 mm (also listed for the FS 200, SP 200), Ø 40 mm (also listed for the FS 250, HT 250). Not interchangeable — measure your cylinder before ordering.
Parts (27)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4134 020 2600 | Crankcase | 1 |
| 2 | 0000 988 8600 | Sleeve | 4 |
| 3 | 9503 003 0242 | Grooved ball bearing 6201 | 1 |
| 4 | 4134 020 2900 | Crankcase | 1 |
| 5 | 9640 003 1195 | Oil seal 12x22x5 Fitment / change note → | 2 |
| 6 | 4134 030 0403 | Crankshaft | 1 |
| 7 | 4140 036 0300 | Washer | 2 |
| 8 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 4 |
| 9 | 4134 029 2300 | Cylinder gasket | 1 |
| 10 | 9512 003 2250 | Needle cage 10x13x12.5 | 1 |
| 11 | 9075 478 4175 | Pan head self-tapping screw IS-D5x28 | 4 |
| 12 | 4134 020 1211 | Cylinder with piston Ø 35 mm | 1 |
| 13 | 4134 030 2011 | Piston Ø 35 mm | 1 |
| 14 | 4119 034 3001 | Piston ring Ø 35x1.5 mm | 2 |
| 15 | 4134 020 1216 | Cylinder with piston Ø 40 mm | 1 |
| 16 | 4134 030 2003 | Piston Ø 40 mm | 1 |
| 17 | 1114 034 3001 | Piston ring Ø 40x1.5 mm | 2 |
| 18 | 4134 020 1210 NLA | Cylinder with piston Ø 38 mm | 1 |
| 19 | 4134 030 2010 NLA | Piston Ø 38 mm | 1 |
| 20 | 4119 034 3002 | Piston ring Ø 38x1.5 mm | 2 |
| 21 | 4119 034 1500 | Piston pin 10x6.5x28 | 1 |
| 22 | 9463 650 1000 | Snap ring 10 | 2 |
| 23 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 24 | 1128 020 9400 | Decompression valve | 1 |
| 25 | 4134 149 0600 | Muffler gasket | 1 |
| 26 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4134 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI09: narrower crankshaft oil seals retrofit older machines
The 12x22x5 seal replaces the 12x22x7 seal; no installation-depth value is invented.
- To facilitate installation, 7 mm wide oil seal 9640 003 1200 (DIN3760-BS12x22x7) is replaced by 5 mm wide seal 9640 003 1195 (DIN3760-BS12x22x5). The diameter pair remains 12 x 22 mm; the changed dimension is width.
- The new seals may also be used in older machines and are installed in the same way as before. The diagram shows their crankshaft locations but supplies no numerical seating depth or alternate installation method.
- Introduction is in progress; the previous seal is no longer available from the factory. No serial cutoff is stated here, and the preceding clutch USA serial must not be applied to these seals.
- Only the printed TI09/2003 models and described configurations are covered. Shared catalog sheets do not extend this assertion to FS 300, BT 121, SP 200, HT 250 or unlisted R variants. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 21 · TI 9/2003, p. 22 — 6 oil seals and summary.
Part numbers (2)
- 9640 003 1200 — Oil seal12x22x7Previous; discontinued factory supply · TI09/2003 section 6 oil seals and summary models/configurations only; preserve restrictions above
- 9640 003 1195 — Oil seal12x22x5New; older-machine use allowed · TI09/2003 section 6 oil seals and summary models/configurations only; preserve restrictions above
Service note · FS 120 / FS 200 / FS 350 / FS 400 / FS 450
FS120/200/350/400/450: four-port engine specifications
FS200 and FS350 share the printed column; all strokes are32 mm.
- New single-cylinder two-stroke engine uses FOUR-PORT technology. Better mixture control, clean combustion and lower emissions are source claims without measured values here. Decompression valve is specified ONLY FOR FS350/400/450, not FS120/200.
- Engine table: FS120 =30.8 cc (1.88 ci),35 mm (1.37 in) bore,1.3 kW (1.8 bhp). SHARED FS200/FS350 column =36.3 cc (2.21 ci),38 mm (1.49 in) bore,1.6 kW (2.2 bhp). FS400 =40.2 cc (2.45 ci),40 mm (1.57 in),1.9 kW (2.6 bhp). FS450 =44.3 cc (2.70 ci),42 mm (1.65 in),2.1 kW (2.8 bhp). Power is to ISO8893.
- ALL four columns specify32 mm (1.26 in) stroke. Rewind starter is SINGLE PAWL with ElastoStart grip. Easy-start description also specifies manual fuel primer and the model-limited decompression valve. Starter-rope entry delegates to section4; the reviewed ElastoStart note resolves it as grip-with-rope0000 190 3400 and separate rope0000 195 8200, without inferred dimensions.
- These are1997 engine specifications; shared catalog sheets also naming FS250/300/480 do not extend these values to those models.
- Historical TI42/1997 configurations only, not all later versions sharing a model name. No hardware operation was performed. No part interchange or numeric serial cutoff is established.
Source: TI 42/1997, p. 2 · TI 42/1997, p. 3 · TI 42/1997, p. 6 — Section1 powerhead/cylinder/easy-start; section2.1.1 complete engine table; section4 starter-rope cross-reference.
No additional parts-table entry added.
Service note · FS 300 / FS 350 / FS 400 / FS 450
FS 300 / 350 / 400 / 450: early crankshaft puller hole modification
Puller 4119 890 4600 can replace service tool ZS on the clutch side; early tools may require the illustrated holes.
- Section 3.2 identifies puller 4119 890 4600 as an alternative to “service tool ZS” for removing the crankshaft from the CLUTCH SIDE of the crankcase. This is a service-tool application within the bulletin’s FS 300/350/400/450 scope, not an installed machine part or a claim for every ZS application.
- EARLY VERSIONS may lack the two holes required for this job. In that case the bulletin instructs modifying the TOOL as shown: drill a NEW 6 mm diameter hole (1); open up the EXISTING 6 mm diameter hole (2) to make a SLOT shown by a broken line. It is not a direction to drill the crankcase or make both holes into slots.
- Figure 255TI005 KN labels the central threaded hole M10. Hole (1) is on its left at the printed horizontal dimension 45; hole (2) is on its right at 47. The slot direction at (2) is shown with a 51° angle to the depicted downward vertical reference. The original drawing is the controlling geometry; the numbers 45 and 47 have no unit suffix in the sketch and are retained as printed rather than a manufactured drilling template.
- The central M10 label is not the diameter of the two 6 mm holes. Do not infer an M10 thread pitch, drill depth, slot length or fabrication tolerance: none is specified here. The retained text OCR’s stray “fo” near 47 is not a separate dimension. All other holes in the outline are drawing context, not additional modification instructions.
- The exact-model crankcase sheets are navigation only; the tool has no invented IPL row or part position. The complete crankshaft-removal procedure and physical tool suitability are not established by this modification note. Shared FS 480 catalog context does not extend the named model scope.
- Historical source guidance; no present-day stock guarantee or verified physical interchange. No hardware operation was performed.
Source: TI 20/1998, p. 1 · TI 20/1998, p. 4 — Page 4 section 3.2 and complete dimensioned drawing255TI005 KN; page 1 exact model scope.
Part numbers (1)
- 4119 890 4600 — Crankshaft pullerService tool; early-tool hole modification · Clutch-side crankshaft removal for the named FS models
Wrong number or missing part for the FS 300, FS 350? Report a correction →