← Augers/Drills & other equipment · series 4134

Stihl 4134 · Section L · 11 of 14 · 26 parts

Gear head

Fits FS 300, FS 350.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101111121213131414151516171819220212223243456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (26)

PosPart numberDescriptionQty
1 4128 641 0351 Gear housing 1
2 9503 003 0210 Grooved ball bearing 6001 1
3 9503 003 5180 Grooved ball bearing 6001-Z 1
4 9455 621 1130 Circlip 12x1 1
5 not sold separately Drive pinion not available as a separate item 1
6 not sold separately Drive shaft not available as a separate item 1
7 0000 953 1001 Stud 1
8 9503 003 0100 Grooved ball bearing 6000 1
9 9503 003 7450 Grooved ball bearing 6202-2RS 1
10 4128 717 2704 Guard ring 1
11 9022 399 0950 Spline screw IS-M5x10 3
12 4128 710 3800 Thrust plate Fitment / change note → 1
13 4116 717 2800 Guard washer Ø 60 mm / 2 3/8'' Fitment / change note → 1
14 4119 642 7600 Collar nut M12x1.5 l/h thread 1
15 4128 713 1600 Thrust washer Fitment / change note → 1
16 4119 717 2800 Guard washer Fitment / change note → 1
17 4119 713 6500 Screw plug 1
18 9291 021 0140 Washer 6.4 Fitment / change note → 2
19 9075 478 4712 Pan head self-tapping screw IS-D6x28 Fitment / change note → 2
20 4128 717 2707 Guard ring 1
21 4119 713 3100 Rider plate 1
22 4116 713 3100 Rider plate 1
23 4116 717 2702 Guard ring option 1
24 0781 120 1117 Gear lubricant 80 g option 1
Not numbered on the diagram — assemblies, kits and options
— 4128 640 0101 Gearhead 1
— 4128 640 7302 Set of pinions 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · FS 300 / FS 350 / FS 400 / FS 450

FS 300 / 350 / 400 / 450: complete gearheads interchange, not individual parts

Ratio changes from 1.235 to 1.4; FS 300/350 have a serial cutoff, FS 400/450 do not.

1 39 373 454 — FS 300 / FS 350 new gearhead only; FS 400 / FS 450 introduction in progress, without a printed serial.

  • TI 20/1998 announces a gear ratio of 1.4 instead of 1.235. FS 300 and FS 350: from machine number 1 39 373 454. FS 400 and FS 450: in the near future / introduction IN PROGRESS, with no serial cutoff. The printed FS 300/350 number must not be applied to FS 400/450 or to the separate handle spring and muffler changes.
  • ONLY THE COMPLETE new and original gearhead assemblies are fully interchangeable: original 4119 640 0102 and new 4128 640 0125. This is not permission to mix their housings, gears, shafts, guard rings or thrust hardware. The replacement comes with the MOWING guard ring already fitted and a separate SAWING guard ring, making the complete replacement suitable for either machine version.
  • Figure 255TI002 KN: output shaft, thrust plate and thrust washer are interconnected by the splined shaft. Two IS-DG 6x28 screws clamp the gearhead to the drive tube; three IS-DG 5x12 screws secure the guard ring to the housing. The mounting procedure is separately preserved with its clean-clamp, washer, stage and torque requirements.
  • Table item 1 original housing includes item 5. Original pinion set contains items 2 and 3; NEW pinion set contains items 2 TO 4, including the output shaft. Drive pinion (2) and spur bevel gear (3) are marked -*- in BOTH columns; new output shaft (4) is also -*-, not a new standalone part number. Original shaft has its own number. Preserve the symbols without inventing a standalone new gear/shaft number.
  • Original item 5 screw and item 10 screws have dashes in the new column; new item 6 screws, item 7 washers and item 11 screws have dashes in the original column. Item 10 quantity is TWO; item 11 quantity is THREE. Both thrust plates (item 12) include guard washer 13. Guard washers 13 and 14 retain their respective numbers in both columns; they are not the same washer. All other parts as before.
  • Remark 1 applies to the original COMPLETE gearhead: remains available FOR OTHER MODELS. Remark 2 applies to the original housing, pinion set, output shaft, item 5 screw, both guard rings, item 10 screws, thrust plate and thrust washer: remain available AS SPARES. These historical supply statements do not identify other models or erase the complete-assembly-only restriction.
  • Later catalog sheets remain edition-specific: L/Q list gearhead 4128 640 0101, housing 4128 641 0351 and pinion set 4128 640 7302. R (05.2003) retains gearhead 4128 640 0125 but lists housing 4128 641 0350 and pinion set 4128 640 7301. S (20.1998) lists the older housing and pinion set, with an IS-M5x25 screw rather than the TI’s IS M5x20. These differences are not silently corrected or treated as identical internals; the shared FS 480 heading does not add FS 480 to this TI.
  • Historical source guidance; no present-day stock guarantee or verified physical interchange. No hardware operation was performed.

Source: TI 20/1998, p. 1 · TI 20/1998, p. 2 — Pages 1–2 section 1, complete gearhead figure and summary, both introduction lines and remarks.

Part numbers (22)
  • 4119 640 0102 — Original complete gearheadOriginal; remark 1, retained for other models · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4128 640 0125 — New complete gearheadComplete-assembly interchange only · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4119 640 0501 — Original gear housing, item 1; includes item 5Original; remark 2, remains spare · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4128 641 0305 — New gear housing, item 1New housing; no individual interchange claim · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4119 640 7300 — Original pinion set, items 2 and 3Original; remark 2, remains spare · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4128 640 7300 — New pinion set, items 2 to 4Includes output shaft; not just two gears · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4119 642 0601 — Original output shaft, item 4Original; remark 2, remains spare · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 9022 371 1020 — Original IS M5x20 spline screw, item 5Original; remark 2, remains spare · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 9075 478 4712 — New IS-DG6x28 spline screw, item 6Two drive-tube clamp screws · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 9291 021 0140 — Washer A 6.4, item 7New clamp washers · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4119 717 2806 — Original mowing guard ring, item 8Original; remark 2, remains spare · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4128 717 2700 — New mowing guard ring, item 8Already fitted to replacement gearhead · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4119 717 2807 — Original sawing guard ring, item 9Original; remark 2, remains spare · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4128 717 2705 — New sawing guard ring, item 9Supplied separately with replacement gearhead · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 9022 313 0930 — Original IS M5x8 spline screw, item 10Two; original remark 2, remains spare · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 9075 478 4095 — New IS-DG5x12 spline screw, item 11Three guard-ring screws · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4116 710 3800 — Original thrust plate, item 12; includes item 13Original; remark 2, remains spare · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4128 710 3800 — New thrust plate, item 12; includes item 13New splined arrangement · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4116 717 2800 — Guard washer, item 13Same number in original and new columns · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4119 717 2800 — Guard washer, item 14Same number in original and new columns · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4116 713 1600 — Original thrust washer, item 15Original; remark 2, remains spare · FS 300 / 350 / 400 / 450; complete-assembly-only restriction
  • 4128 713 1600 — New thrust washer, item 15New splined arrangement · FS 300 / 350 / 400 / 450; complete-assembly-only restriction

Service note · FS 300 / FS 350 / FS 400 / FS 450

FS 300 / 350 / 400 / 450: new gearhead clamp tightening sequence

New installation uses 12 Nm; refitting uses 8 Nm, always second screw before first.

  • Section 3.1 applies specifically to the NEW gearhead announced in section 1, not every old or later gearhead on these model sheets. Drive tube and gearhead must be CLEAN AND FREE FROM GREASE in the clamp area. Always use a torque wrench, tighten in TWO STAGES and USE WASHERS.
  • STAGE 1: fit the FIRST clamp screw and tighten only until the gap begins to close. It must not close any more than 0.3 mm at this stage. This limits the amount of closure; it does NOT specify a final 0.3 mm gap or instruct closing the clamp completely.
  • STAGE 2, INITIAL INSTALLATION (NEW PART): tighten the SECOND clamp screw to 12 Nm, then the FIRST clamp screw to 12 Nm. REFITTING: SECOND screw to 8 Nm, then FIRST screw to 8 Nm. Do not substitute the new-part torque for refitting or reverse the printed order.
  • Figure 255TI004 KN arrows identify the two remaining gaps: these must be ABOUT THE SAME ON BOTH SIDES. The bulletin says following this procedure is essential to avoid damage from internal stresses in the gearhead neck. No numeric final gap or extra alternating retorque cycle is given.
  • Section 1 identifies clamp screw 9075 478 4712 and washer A 6.4 9291 021 0140. Later catalog sheet links are navigation, not proof that the 1998 procedure applies to a differently revised assembly. No torque experiment or physical installation was performed.
  • Historical source guidance; no present-day stock guarantee or verified physical interchange. No hardware operation was performed.

Source: TI 20/1998, p. 1 · TI 20/1998, p. 2 · TI 20/1998, p. 3 — Page 3 entire section 3.1 and gap-arrow diagram; pages 1–2 exact new gearhead context.

Part numbers (2)
  • 9075 478 4712 — IS-DG6x28 clamp screwTwo screws; second then first · New section-1 gearhead clamp; initial versus refitting torque applies
  • 9291 021 0140 — Washer A 6.4Required washers · New section-1 gearhead clamp; initial versus refitting torque applies

Wrong number or missing part for the FS 300, FS 350? Report a correction →