Stihl 4134 · Section N · 13 of 13 · 10 parts
Tools, Extras
Fits SP 200.
Historical fitment & changes (58) — includes parts and conditions not shown on this drawing.
Parts (10)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4234 710 9000 | Harness | 1 |
| 2 | 4234 718 6900 | Spring safety hook | 2 |
| 3 | 4233 790 8800 | Loop | 2 |
| 4 | 0000 890 2300 NLA | Screwdriver | 1 |
| 5 | 4233 893 1303 | Wrench 36 Fitment / change note → | 1 |
| 6 | 4233 893 1300 | Wrench 47 Fitment / change note → | 1 |
| 7 | 4128 890 3400 | Combination wrench | 1 |
| 8 | 4234 891 0800 | Tool roll | 1 |
| 9 | 4233 718 6400 | Pad | 1 |
| 10 | 0000 884 0307 | Safety glasses | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · SP 200
SP 200 Loctite 243: coat half the overlapping thread
Clean both threads and protect thread flanks when reusing parts.
- The table identifies Loctite 243 threadlocker as 0786 110 0101. For new parts, remove grease, oil, dust and other dirt from both inside and outside threads with an appropriate solvent.
- Apply threadlocker over the full circumferential surface for a length equal to HALF the overlapping thread, starting at the beginning of the outside thread; then assemble and tighten the joint. This is not half of every screw’s total length.
- For disassembled parts, clean with a wire brush or similar without damaging the thread flanks, then follow the new-part preparation. This general section does not give a torque or cure time and does not approve Loctite 243 in joints specified for 326 or 638.
- These are general SP 200 adhesive preparation rules, not permission to apply every adhesive to every joint. Follow the component-specific adhesive, disassembly, alignment and tightening instructions. The control handle, drive tube, gearhead, pushrod, hook, harness and tool roster are reviewed in separate notes; this adhesive note alone is not a complete repair procedure. The bulletin identifies the harvester as series 4233; the local 1129/4134 catalog groups contain exact SP 200 tool sheets and do not extend applicability to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 1 · TI 34/2003, p. 2 — 1 general consumable table; 1.1.1 Loctite 243.
Part numbers (1)
- 0786 110 0101 — Loctite 243 threadlockerHistorical service consumable; not a universal substitution · SP 200; only joints specified for this adhesive
Service note · SP 200
SP 200 Loctite 326: activator and less than 60 seconds working time
Coat two-thirds of the overlapping joint; do not confuse working time with full cure.
- Fast-curing adhesive Loctite 326 is 0786 110 1004. Activator Loctite 7649 promotes even curing, including larger joints; the STIHL order-number column is a dash, so no activator order number is invented.
- For new parts, surfaces MAY be roughened with fine sandpaper to improve adhesion. Remove grease, oil, dust and other dirt with an appropriate solvent. Apply activator 7649 to ONE surface, or BOTH surfaces if the gap is large, and allow it to volatilize.
- Apply adhesive evenly over the full surface along TWO-THIRDS of the overlap, beginning at the start of the outward-facing joining surface. Slowly bring surfaces into contact and push/pull to distribute the adhesive evenly.
- Working time is LESS THAN 60 SECONDS. This is not a sixty-second minimum and not a full-cure specification. For reused parts, remove adhesive residues with sandpaper or similar, then proceed as for new parts. No numeric large-gap threshold or full-cure time is supplied.
- These are general SP 200 adhesive preparation rules, not permission to apply every adhesive to every joint. Follow the component-specific adhesive, disassembly, alignment and tightening instructions. The control handle, drive tube, gearhead, pushrod, hook, harness and tool roster are reviewed in separate notes; this adhesive note alone is not a complete repair procedure. The bulletin identifies the harvester as series 4233; the local 1129/4134 catalog groups contain exact SP 200 tool sheets and do not extend applicability to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 1 · TI 34/2003, p. 2 — 1 consumable table; 1.1.2 Loctite 326 and activator7649.
Part numbers (1)
- 0786 110 1004 — Loctite 326 fast-curing adhesiveHistorical service consumable; not a universal substitution · SP 200; only joints specified for this adhesive
Service note · SP 200
SP 200 Loctite 638: threads and bearing surfaces differ
Thread overlap gets half-length coverage; the bearing outer ring gets full coverage.
- Loctite 638 retaining compound is 0786 110 1005. For threaded joints, clean inside/outside threads with an appropriate solvent; apply evenly over the full thread surface for HALF the overlap length, starting at the outside-thread beginning, then assemble and tighten.
- For reused threaded parts, wire-brush or similarly clean the thread without damaging its flanks, then follow the new-part procedure. Do not transfer the two-thirds rule for Loctite 326 bonded surfaces to these threads.
- Under the printed Plain bearings heading, clean joining surfaces with solvent, coat the WHOLE OUTER RING of the bearing, insert into its housing and remove surplus adhesive with an appropriate solvent. Do not apply the half-thread-length rule to the bearing outer ring.
- For disassembled bearing joints, remove adhesive residue with sandpaper or similar, then follow the new-part sequence. No press fit, torque, bearing identity or cure time is established by this general section alone.
- These are general SP 200 adhesive preparation rules, not permission to apply every adhesive to every joint. Follow the component-specific adhesive, disassembly, alignment and tightening instructions. The control handle, drive tube, gearhead, pushrod, hook, harness and tool roster are reviewed in separate notes; this adhesive note alone is not a complete repair procedure. The bulletin identifies the harvester as series 4233; the local 1129/4134 catalog groups contain exact SP 200 tool sheets and do not extend applicability to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 1 · TI 34/2003, p. 2 · TI 34/2003, p. 3 — 1 consumable table; 1.1.3 complete across pages2–3.
Part numbers (1)
- 0786 110 1005 — Loctite 638 retaining compoundHistorical service consumable; not a universal substitution · SP 200; only joints specified for this adhesive
Service note · SP 200
SP 200 adhesive release: 600°C describes the hot-air jet
Heat the bond evenly and check frequently; it is not a component-temperature target.
- The bulletin says all adhesives used here can be released by heat and recommends an ELECTRIC hot-air blower producing a jet of at least 600°C. That number describes the air jet, NOT a required measured part temperature or a universal setting for unrelated materials.
- Its stated purpose is rapid heating of the bond without damaging other parts. Heat the bond area as evenly as possible. Slight crackling indicates loosening; check frequently whether the bond has released. Contact with hot parts can cause burns. No fixed dwell time, part-temperature setpoint or open-flame method is specified.
- Section 2 introduces reproducible workbench drawings A control handle, B drive tube assembly, C gearhead and D pushrod/hook. This index supplies no additional part numbers or torque values. Drawings A/B/C/D and sections 3–8 are reviewed in separate notes; this overview alone is not a complete repair procedure. This note is not a complete disassembly procedure.
- These are general SP 200 adhesive preparation rules, not permission to apply every adhesive to every joint. Follow the component-specific adhesive, disassembly, alignment and tightening instructions. The control handle, drive tube, gearhead, pushrod, hook, harness and tool roster are reviewed in separate notes; this adhesive note alone is not a complete repair procedure. The bulletin identifies the harvester as series 4233; the local 1129/4134 catalog groups contain exact SP 200 tool sheets and do not extend applicability to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 1 · TI 34/2003, p. 2 · TI 34/2003, p. 3 — 1.2 Removing adhesive;2 general drawing index.
No additional parts-table entry added.
Service note · SP 200
SP 200 handle supports: Loctite 326 and two distinct torques
Drawing A assigns 10 Nm and 15 Nm to different fasteners.
- Undo the support screws and remove tube (2) and control handle (3). Clamp the tube, release the adhesive on one handle support (1) using section 1.2, then remove that support. Slacken the control-handle attachment screws and remove the handle; remove the second support only if necessary.
- Fit the control handle to the tube, prepare the bond and apply Loctite 326 under section 1.1.2, press on the support, line it up, then install and tighten the support screws. The activator, two-thirds overlap coverage and LESS THAN 60 SECONDS working time apply; this is not a full-cure time.
- Drawing A shows 10 Nm for the paired screws through each small rectangular clamping plate, and 15 Nm for the separate long retainer-clamp screw at each end. Keep these visibly distinct fasteners separate; neither value is supplied for the control handle’s own attachment screws. Supports (1), tube (2), control handle (3) and intervening plates (4) retain the illustrated order.
- Adhesive release uses an electric hot-air jet as in section 1.2; the at-least-600°C figure is air temperature, not a part-temperature target. Check frequently and avoid burns.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 2 · TI 34/2003, p. 3 · TI 34/2003, p. 4 · TI 34/2003, p. 6 — Drawing A; section 3 complete; 1.1.2/1.2.
Part numbers (1)
- 0786 110 1004 — Loctite 326Specified handle-support adhesive · SP 200; specified procedure only
Service note · SP 200
SP 200 engine-end tube: the shaft stays with the clutch drum
Separate the tube without assuming the engine-end shaft is loose.
- To separate the front drive-tube assembly, slacken union nut (12) with 47 mm special wrench 4233 893 1300 while counterholding the gearhead-end drive tube with 38 mm wrench 4233 893 1302. These wrench sizes are tool openings, not thread sizes.
- At the engine end, slacken the clutch-housing attachment screw and the handle-support retainer screws (drawing A), then pull out tube (1). Shaft (4) is BOLTED TO THE CLUTCH DRUM and stays attached to the engine; pulling the tube is not shaft removal.
- Prise out plug (2), dismantle flexible liner (3), and reassemble in reverse order. Drawing B distinguishes engine-end tube/liner/shaft (1/3/4) from gearhead-end tube/liner/shaft (13/14/15); similarly drawn plugs (2) do not make the shafts interchangeable.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 4 · TI 34/2003, p. 7 · TI 34/2003, p. 23 — Drawing B; section 4 introduction and 4.1.
Part numbers (2)
- 4233 893 1300 — 47 mm special wrenchFront union nut (12) · SP 200; specified procedure only
- 4233 893 1302 — 38 mm special wrenchCounterholding and plug (8) operations · SP 200; specified procedure only
Service note · SP 200
SP 200 drive-shaft screw: heat release, 5 mm key and Loctite 638
The 30 Nm coupling-plug callout is not this shaft screw’s torque.
- After removing the engine-end tube under 4.1, remove screws (17) and clutch housing (28). Hold shaft (4) in special tool 4233 890 2200. Apply the section 1.2 high-temperature hot-air method to release adhesive at screw (18); undo it with a 5 mm hexagon socket key.
- Remove shaft (4), using a plastic hammer and punch if necessary. On refitting, position the shaft, apply Loctite 638 to screw (18) under section 1.1.3, counterhold with 4233 890 2200 and tighten with the 5 mm key; complete assembly in reverse order.
- The threaded-joint 638 preparation requires clean threads and half-overlap coverage; the bearing outer-ring rule does not apply to this screw. Sections 4.1.1/4.1.2 give NO numeric tightening torque for screw (18). Drawing B’s 30 Nm arrow points to coupling plug (8), not this screw; do not transfer that value.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 2 · TI 34/2003, p. 3 · TI 34/2003, p. 4 · TI 34/2003, p. 7 · TI 34/2003, p. 8 · TI 34/2003, p. 23 — Drawing B; 4.1.1 and 4.1.2 complete.
Part numbers (2)
- 4233 890 2200 — Holding toolCounterhold drive shaft · SP 200; specified procedure only
- 0786 110 1005 — Loctite 638Specified shaft-screw retaining compound · SP 200; specified procedure only
Service note · SP 200
SP 200 swivel coupling: plug torque, seal and bearing-stack order
Keep the two union nuts and the 30 Nm plug distinct.
- With appropriate circlip pliers, remove the first ring (11), union nut (12), then the second ring (11). Counterhold plug (8) with 4233 893 1302 and undo union nut (10) with 4233 893 1301. Release plug adhesive by the section 1.2 hot-air method, then unscrew plug (8) with 4233 893 1302.
- Drawing B shows the coupling core (7) flanked by stacks (5)-(6)-(5), then O-ring (9) and plug (8). Preserve the illustrated stack order; the drawing does not establish new order numbers or universal bearing substitutions.
- For assembly, place O-ring (9) in plug (8), apply Loctite 243 to the plug THREAD under section 1.1.1, and install with 4233 893 1302. Drawing B specifies 30 Nm at PLUG (8), not union nut (10) or front union nut (12). Tighten union nut (10) separately; no numeric torque for either union nut is supplied here.
- Page 9 prints tool 4133 893 1301 for tightening union nut (10), while disassembly on page 8 and the 55 mm wrench illustration on page 23 say 4233 893 1301. This is a documented SOURCE CONFLICT, not evidence of two approved interchangeable tools. The separate tool-number note retains both readings; ring refitting follows the separate bevel-orientation note.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 2 · TI 34/2003, p. 3 · TI 34/2003, p. 4 · TI 34/2003, p. 8 · TI 34/2003, p. 9 · TI 34/2003, p. 23 — Drawing B; 4.2.1 and plug/union-nut portion of 4.2.2.
Part numbers (3)
- 4233 893 1301 — 55 mm special wrenchPage 8 and page 23 union-nut tool; page 9 conflicts · SP 200; specified procedure only
- 4233 893 1302 — 38 mm special wrenchPlug (8) counterhold/removal/refitting · SP 200; specified procedure only
- 0786 110 0101 — Loctite 243Specified coupling-plug threadlocker · SP 200; specified procedure only
Service note · SP 200
SP 200 coupling rings: bevels face the union nut
The temporary cone ring is removed before the second ring is fitted.
- Place temporary ring (19), special tool 4233 893 7000, in the cone groove. Position the WHITE ring (11) with its bevelled surface TOWARDS THE UNION NUT and press it on with sleeve (20). Remove temporary tool ring (19) from the cone groove again; it is not a retained machine part.
- Place the second ring (11) into union nut (12), again with its bevelled surface TOWARDS THE UNION NUT, and press on with sleeve (20). Complete assembly in reverse order to disassembly. The same drawing item (11) covers the two rings; the white-ring instruction is explicit for the first refitting step.
- SOURCE CONFLICT: page 9 first calls sleeve (20) 4233 894 4902, then calls it 4233 893 4902 for the second ring; page 25’s illustration also reads 4233 893 4902. The original scan confirms 894 in the first occurrence even though extracted text normalizes it to 893. Both printed readings are retained, not promoted into two interchangeable tools.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 4 · TI 34/2003, p. 8 · TI 34/2003, p. 9 · TI 34/2003, p. 25 — Drawing B; complete ring-refitting portion of 4.2.2.
Part numbers (2)
- 4233 893 7000 — Temporary cone-groove ringAssembly aid; remove after first ring · SP 200; specified procedure only
- 4233 893 4902 — Press sleeveSecond page 9 step and page 25 illustration; first step conflicts · SP 200; specified procedure only
Service note · SP 200
SP 200 tool-number conflicts: 4133/4233 and 894/893
Original page 9 disagrees with its own procedure and tool illustrations.
- For union nut (10), page 9 PRINTS 4133 893 1301. Page 8 disassembly and page 23 illustration instead print 4233 893 1301 (55 mm). Retain 4133 as a conflicting printed reference, not a second verified application or an automatic substitute.
- For sleeve (20), the first ring-refitting bullet on the page 9 SCAN prints 4233 894 4902; the second bullet and page 25 illustration print 4233 893 4902. Extracted body text renders the first as 893, so the scan discrepancy must not disappear merely because a text search agrees.
- The repeated procedure and illustration readings support likely printing errors, but no erratum or physical tool verification is supplied. Keep both contradictions explicit and verify the actual tool identity before use; no interchange is established.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 8 · TI 34/2003, p. 9 · TI 34/2003, p. 23 · TI 34/2003, p. 25 — 4.2.1/4.2.2 versus 8.2 tool illustrations.
Part numbers (4)
- 4133 893 1301 — Conflicting printed union-nut tool referencePage 9 only; not confirmed fitment · SP 200; specified procedure only
- 4233 893 1301 — Illustrated 55 mm wrenchPage 8/page 23 reading · SP 200; specified procedure only
- 4233 894 4902 — Conflicting printed sleeve referenceOriginal page 9 scan only; body extraction differs · SP 200; specified procedure only
- 4233 893 4902 — Illustrated press sleeveSecond page 9 step/page 25 reading · SP 200; specified procedure only
Service note · SP 200
SP 200 gearhead-end tube: shaft circlip and centered refit
Refit with the coupling centered and hook pointing down.
- Slacken the gearhead attachment screw and remove the gearhead. Prise out plug (2), withdraw flexible liner (14) and shaft (15), remove circlip (16), then pull shaft (15) from the liner. Reassemble in reverse order, including the shaft-retaining circlip; this is distinct from the coupling rings (11).
- Section 4.3 explicitly requires gearhead alignment under 5.5. Push the gearhead onto the drive tube, rotate the swivel coupling to its CENTER POSITION of 135° within the approximately 270° total swivel travel, then hold the gearhead vertically with the HOOK DOWNWARDS and tighten attachment screw (7). Drawing C gives 12 Nm for this screw.
- The 135° value identifies the midpoint of travel, not a 135° tilt of the gearhead from vertical. This alignment note does not replace gear-oil fill/sealing requirements after gearbox work. The oil/seal and internal gearhead procedures are reviewed in separate notes; this alignment note alone is not a complete gearbox repair procedure.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 4 · TI 34/2003, p. 5 · TI 34/2003, p. 9 · TI 34/2003, p. 17 — Drawing B; 4.3 complete; drawing C and 5.5 alignment.
No additional parts-table entry added.
Service note · SP 200
SP 200 gear oil: 110 ml change versus 120 ml assembly fill
Retain both source quantities and replace the drain-plug sealing ring.
- First oil change after 20–25 operating hours; thereafter regularly as required. No fixed later-hour interval is supplied. Turn the tube until screw plug (2) faces down, place a suitable catch container underneath, remove plug (2) with sealing ring (3), and drain completely. The housing may be warmed SLIGHTLY with a hot-air blower to liquefy the oil; this is not the high-temperature adhesive-release operation.
- Section 5.1 specifies APPROXIMATELY 110 ml of gear oil 0781 313 7001 (Klüber Syntheso D 150 EP), poured through the drain hole. The oil change can alternatively be done with the gearbox removed. Section 5.5, following gearhead assembly, instead specifies 120 ml of the SAME oil through the drain hole.
- Keep 110 ml and 120 ml attached to their respective procedure contexts. The bulletin does not explain the 10 ml difference or explicitly label it residual oil versus dry capacity; do not silently choose a universal fill, average the values, or claim a verified explanation.
- Both procedures require a NEW sealing ring 4233 649 0200 over the screw plug. Drawing C gives 9 Nm for plug (2). Gearhead attachment/alignment still requires midpoint 135° within approximately 270° total swivel travel, vertical gearhead and hook downward; clamp screw (7) is 12 Nm, not the drain-plug torque.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 5 · TI 34/2003, p. 10 · TI 34/2003, p. 17 — Drawing C; 5.1 complete and 5.5 fill/seal.
Part numbers (2)
- 0781 313 7001 — Klüber Syntheso D 150 EP gear oilOil-change and assembly-fill quantities differ · SP 200; specified procedure only
- 4233 649 0200 — Drain-plug sealing ringReplace for either fill procedure · SP 200; specified procedure only
Service note · SP 200
SP 200 gear housing: heat-release screw, seal cover and refit plug
Keep 20 Nm internal screw and 6 Nm cover screws separate.
- Slacken attachment screw (7), pull the gearbox from the tube and drain the oil before internal dismantling. Prise out plug (8) with a suitable tool, steady the gearhead with 4233 890 2200, and heat-release adhesive at screw (9) under section 1.2. Undo screw (9) with a 6 mm hexagon socket key. Remove screws (26) and cover (25).
- To close after internal assembly, apply Dirko HT RED sealant 0783 830 2000 to the gear-housing edge, fit cover (25), and tighten screws (26) to 6 Nm as shown in drawing C. No bead size or cure time is supplied here; do not invent one.
- Steady the gearhead with 4233 890 2200, apply Loctite 638 to screw (9) threads under section 1.1.3, install and tighten. Drawing C specifies 20 Nm for this screw. Push plug (8) into place with 4233 893 1500. Plug (8) is not the oil-drain screw plug (2) or drive-pinion plug (20).
- Complete the separate section 5.5 oil fill, NEW drain sealing ring and gearhead-alignment procedure before return to use. The 6 mm internal-screw key must not be confused with the 5 mm engine-end shaft-screw key from section 4.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 2 · TI 34/2003, p. 3 · TI 34/2003, p. 5 · TI 34/2003, p. 10 · TI 34/2003, p. 11 · TI 34/2003, p. 16 · TI 34/2003, p. 17 — 5.2/5.3 prerequisites; 5.3.1 and5.4.5 complete.
Part numbers (4)
- 4233 890 2200 — Holding toolGearhead counterhold · SP 200; specified procedure only
- 0783 830 2000 — Dirko HT red sealantGear-cover sealing edge · SP 200; specified procedure only
- 0786 110 1005 — Loctite 638Internal screw (9) thread retaining compound · SP 200; specified procedure only
- 4233 893 1500 — Press toolRefit plug (8) · SP 200; specified procedure only
Service note · SP 200
SP 200 gear bearings: puller, centering tool and retained washers
Remove the connecting rod evenly; preserve the numbered bearing stack.
- Remove circlips (24) and outer washers (21). Prise connecting rod (22) off EVENLY using TWO suitable tools, then remove needle bearings (23), remaining washers (21) and spur bevel gear (14). Heat the gear housing in the bearing area; no numeric housing temperature is specified.
- Remove grooved ball bearing (13) with a STANDARD internal puller (27), then remove circlip (12), spacer ring (11) and bearing (10). Item (27) is not a STIHL tool order number and no order number is invented.
- For assembly, insert centering tool 4233 893 5400 into the gear housing and press in bearing (10) with 4233 893 1500. Fit circlip (12), then spacer ring (11) and bearing (13), pressing in with 4233 893 1500. Preserve this procedural order; do not omit the circlip because the exploded drawing spaces the rings apart.
- Insert spur bevel gear (14). At the connecting-rod joints fit washers (21) and needle bearings (23), mount rod (22), then fit outer washers (21) and circlips (24). Drawing C shows both ends of the rod with their own bearing/washer/retainer stack; no new bearing dimensions or interchangeable replacement identities are established.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 5 · TI 34/2003, p. 11 · TI 34/2003, p. 15 · TI 34/2003, p. 16 — Drawing C; 5.3.2 and5.4.4 complete.
Part numbers (2)
- 4233 893 5400 — Centering toolBearing assembly alignment · SP 200; specified procedure only
- 4233 893 1500 — Press toolInstall grooved ball bearings (10)/(13) · SP 200; specified procedure only
Service note · SP 200
SP 200 pushrod housing joint: tilt, clamp aids and Loctite 243
The housing-to-gearhead joint is separate from pushrod internals.
- Clamp the gear housing using BOTH special tools 4233 893 5200 and 4233 893 8700. Heat-release the housing bond under section 1.2, unscrew the pushrod housing with 4233 893 1303, then TILT it to separate it from the gear housing.
- On assembly use the same clamping aids, tilt the pushrod housing into the gear housing, apply Loctite 243 to its thread under section 1.1.1, insert it fully, and tighten with 4233 893 1303. Drawing D’s 60 Nm arrow identifies this housing (2), not the neighboring 55 Nm pushrod-end connections.
- Numbering discrepancy retained: the removal figure on page 12 labels the threaded housing (2), while other page 12/page 15 figures and the assembly prose use (18). Drawing D calls the housing (2), whereas drawing C uses (18) for a drive-pinion ring. These are not evidence that those different components interchange; follow the depicted housing-to-gearhead joint.
- This note covers only the housing joint in gearhead section 5. The internal pushrod, hook and harness procedures in sections 6–7 are reviewed separately.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 2 · TI 34/2003, p. 3 · TI 34/2003, p. 5 · TI 34/2003, p. 12 · TI 34/2003, p. 15 — Drawing D housing(2);5.3.3 and5.4.3 complete.
Part numbers (4)
- 4233 893 5200 — Gear-housing clamping aidUse together with4233 893 8700 · SP 200; specified procedure only
- 4233 893 8700 — Gear-housing clamping aidUse together with4233 893 5200 · SP 200; specified procedure only
- 4233 893 1303 — Special housing wrenchHousing removal/refit · SP 200; specified procedure only
- 0786 110 0101 — Loctite 243Housing-joint threadlocker · SP 200; specified procedure only
Service note · SP 200
SP 200 drive pinion: puller controls and separate seal press tool
10 mm and 13 mm operate the puller; 10 Nm tightens the plug.
- Unscrew drive-pinion plug (20) with 4233 893 2800. Insert puller 4233 890 4400 into the gear housing’s drive-tube clamp. Use a 10 mm wrench to screw the tool’s screw INTO THE DRIVE PINION THREAD, then a 13 mm wrench to turn the TOOL NUT and pull out the pinion. These wrench sizes are not tightening torques.
- Dismantle/reassemble the pinion according to drawing C and the section illustrations: shaft/pinion (15) carries two bearings (16) separated by sleeve (17); ring (18), oil seal (19) and plug (20) are separate pieces at the closure end. This ring (18) is not the pushrod housing called (18) in adjacent procedure figures.
- Insert the assembled pinion into the gear housing and push in with 4233 893 1500. Use the DIFFERENT tool 4233 893 1501 to press oil seal (19) INTO PLUG (20), not directly into the gear housing. Insert plug (20), screw in with 4233 893 2800 and tighten to drawing C’s 10 Nm.
- No additional adhesive or sealant is specified for this plug in 5.4.2. Do not transfer coupling-plug 30 Nm, oil-drain-plug 9 Nm or housing-joint Loctite 243 to it merely because each component is called a plug or threaded housing.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 5 · TI 34/2003, p. 12 · TI 34/2003, p. 13 · TI 34/2003, p. 14 — Drawing C;5.3.4 and5.4.2 complete.
Part numbers (4)
- 4233 893 2800 — Drive-pinion plug toolRemove/install plug (20) · SP 200; specified procedure only
- 4233 890 4400 — Drive-pinion puller10 mm screw and13 mm nut operation · SP 200; specified procedure only
- 4233 893 1500 — Press toolInsert drive pinion · SP 200; specified procedure only
- 4233 893 1501 — Oil-seal press toolPress oil seal into plug (20) · SP 200; specified procedure only
Service note · SP 200
SP 200 thrust plates: 2.5 mm key, Loctite 638 and 8 Nm
Hold screws for removal; hold nuts while tightening screws on assembly.
- Heat-release adhesive on nuts (5) under section 1.2. Counterhold screws (4) with hexagon key 4233 893 0900 (2.5 mm) and undo nuts (5). Continue dismantling according to drawing C, retaining both thrust plates (6).
- For assembly position plates (6), apply Loctite 638 to screw (4) threads under section 1.1.3, HOLD THE NUTS (5), then screw in and tighten screws (4). Drawing C shows 8 Nm at these fastener pairs on both sides; no separate additional tightening torque is assigned to the nuts.
- Page 23 illustrates the 2.5 mm key with a 14 mm short leg. Those dimensions describe the special key, not screw thread diameter, screw length or plate thickness. The 638 threaded-joint preparation applies; do not substitute the 326 bonding-surface rule.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 2 · TI 34/2003, p. 3 · TI 34/2003, p. 5 · TI 34/2003, p. 13 · TI 34/2003, p. 14 · TI 34/2003, p. 23 — Drawing C;5.3.5 and5.4.1 complete;tool illustration3.
Part numbers (2)
- 4233 893 0900 — 2.5 mm hexagon key,14 mm short legThrust-plate screw counterhold · SP 200; specified procedure only
- 0786 110 1005 — Loctite 638Thrust-plate screw threads · SP 200; specified procedure only
Service note · SP 200
SP 200 pushrod removal: protect the pin before releasing bonded ends
Use the two pin-end supports, then separate clamping jaws for the rod.
- First complete gearhead removal and dismantling through sections 5.2–5.3.3: remove the gearhead, drain oil, open the housing and remove the connecting rod/bearings as specified, then release the pushrod housing. Unscrew hook (13). Prise off hand guard (10), or cut it off with a sharp knife; the cut guard is not thereby reusable.
- Remove snap ring (9), both washers (7) and needle bearing (8). Attach supports 4233 893 4600 and 4233 893 4601 to the appropriate ends of pin (6), then clamp the forkhead WITH these special tools as illustrated. They support different pin ends, not two interchangeable replacement pins.
- Heat-release adhesive at pushrod (1) under section 1.2, then use an appropriate open-end wrench to unscrew carrier (12). Slide the housing off over the free rod end, remove the pin-end tools, and clamp the free rod end using jaws 5910 893 2700.
- Heat-release the second bonded rod end under section 1.2, then use an appropriate open-end wrench to unscrew forkhead (5). Further housing disassembly follows drawing D, retaining seal (3) and circlip (4) identities. No wrench opening is supplied for either carrier or forkhead; do not invent one from the tool-set wrench sizes.
- The at-least-600°C figure in section 1.2 is HOT-AIR JET temperature, not a prescribed component temperature. Heat evenly, check frequently for release and avoid burns; this is not the slight warming used to drain gear oil.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 3 · TI 34/2003, p. 5 · TI 34/2003, p. 10 · TI 34/2003, p. 11 · TI 34/2003, p. 12 · TI 34/2003, p. 18 · TI 34/2003, p. 19 · TI 34/2003, p. 24 — Drawing D; 6.1 complete with 5.2–5.3.3 prerequisites.
Part numbers (3)
- 4233 893 4600 — Pin-end supportUse together with 4233 893 4601 · SP 200; specified procedure only
- 4233 893 4601 — Pin-end supportUse together with 4233 893 4600 · SP 200; specified procedure only
- 5910 893 2700 — Clamping jawsClamp free pushrod end for forkhead removal · SP 200; specified procedure only
Service note · SP 200
SP 200 pushrod seal: press tool 4900 and retaining circlip
The pushrod oil seal is not the drive-pinion seal.
- Insert pushrod (1) into housing (2), fit oil seal (3), press it in with 4233 893 4900, then fit circlip (4). Preserve the illustrated seal/retainer order; the bulletin supplies no seal order number, dimension or numeric insertion depth here.
- Attach supports 4233 893 4600 and 4233 893 4601 to the appropriate ends of pin (6), then clamp the forkhead and supports for the following threaded assembly. The pushrod seal tool 4900 is distinct from the drive-pinion seal tool 4233 893 1501 and the hand-guard tool 4233 893 4901.
- The source subsequently repeats an instruction to attach the housing over the free end after the rod has been screwed into the forkhead. Retain this assembly context without construing it as a second housing or second oil seal; consult the linked drawings for positioning.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 5 · TI 34/2003, p. 19 · TI 34/2003, p. 24 — Drawing D; 6.2 opening seal and clamping sequence.
Part numbers (3)
- 4233 893 4900 — Pushrod oil-seal press sleevePress oil seal (3) · SP 200; specified procedure only
- 4233 893 4600 — Pin-end supportForkhead clamping · SP 200; specified procedure only
- 4233 893 4601 — Pin-end supportForkhead clamping · SP 200; specified procedure only
Service note · SP 200
SP 200 pushrod ends: Loctite 638, two 55 Nm joints and a numbering error
Do not transfer the housing joint’s 60 Nm to either rod end.
- Clamp the forkhead using the pin-end supports. Apply Loctite 638 to forkhead (5) thread under section 1.1.3 and screw in the pushrod by hand. SOURCE NUMBERING ERROR: page 20 prose calls this “pushrod (5)”, while its illustration and drawing D identify PUSHROD (1) and FORKHEAD (5). Keep the printed discrepancy explicit, not a second pushrod identity.
- Attach the housing over the free rod end as instructed, place washer (11) on carrier (12), apply Loctite 638 to carrier (12) thread under section 1.1.3, insert by hand and tighten with an appropriate wrench. Drawing D specifies 55 Nm at BOTH the forkhead-to-rod and carrier-to-rod threaded joints. The prose gives hand-start steps, not a replacement for these drawing torques.
- The housing-to-gearhead joint has its own 60 Nm and Loctite 243 requirements from section 5.4.3. Do not transfer that torque or adhesive to the two 55 Nm rod-end joints. The 638 threaded-joint preparation is clean threads with half-overlap coverage, not the 326 bonding-surface rule.
- Fit washers (7), needle bearing (8) and snap ring (9) in the illustrated washer–bearing–washer–ring stack on pin (6). Continue with sections 5.4.3–5.5 for housing refit, internal gear assembly, cover sealing, specified assembly oil fill, NEW drain seal and aligned gearhead attachment before fitting the hand guard and hook.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 2 · TI 34/2003, p. 3 · TI 34/2003, p. 5 · TI 34/2003, p. 19 · TI 34/2003, p. 20 — Drawing D; 6.2 bonded joints and pin-bearing assembly.
Part numbers (2)
- 0786 110 1005 — Loctite 638Both pushrod-end threads · SP 200; specified procedure only
- 0786 110 0101 — Loctite 243Separate housing-to-gearhead joint only · SP 200; specified procedure only
Service note · SP 200
SP 200 hand guard: cone 7700 and separate press sleeve 4901
The guard is pressed on after the gearhead assembly sequence.
- After completing sections 5.4.3–5.5, fit special tool 4233 894 7700 over carrier (12) as the illustrated tapered guide. Press on hand guard (10) using sleeve 4233 893 4901, then screw on the hook.
- Keep the tool numbers exact: the cone is 4233 894 7700, not an inferred 893-prefix variant. Sleeve 4901 installs the hand guard; sleeve 4900 installs the pushrod seal and sleeve 4902 serves the drive-tube coupling rings. Similar appearances do not establish substitution.
- Drawing D shows washer (11) beneath carrier (12), and the hand guard around the housing end. The carrier’s 55 Nm callout is not a tightening torque for the hand guard or hook union nut. The guard removal instruction permits cutting the guard; this does not authorize reuse of a cut guard.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 5 · TI 34/2003, p. 18 · TI 34/2003, p. 20 · TI 34/2003, p. 25 — 6.1 guard removal; 6.2 final guard/hook installation; 8.2 figures 15/21.
Part numbers (2)
- 4233 894 7700 — Tapered hand-guard guideFit over carrier (12) · SP 200; specified procedure only
- 4233 893 4901 — Hand-guard press sleevePress hand guard (10) into position · SP 200; specified procedure only
Service note · SP 200
SP 200 hook rubber: replace the insert and realign the hook
The rubber insert is distinct from the cone-connector rings.
- Unscrew hook (13), prise rubber insert (14) out of the hook, fit a NEW rubber insert, then screw the hook back on and line it up. Drawing D shows the insert lining the inside of the hook; rings (16) belong to the separate cone connector.
- No insert order number, alignment angle or tightening torque for the hook union nut (15) is supplied here. Do not borrow either 55 Nm rod-end torque or the 60 Nm housing torque. Gearhead hook-down alignment under 5.5 is a distinct refitting operation.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 5 · TI 34/2003, p. 21 — Drawing D; 6.3 and 6.3.1 complete.
No additional parts-table entry added.
Service note · SP 200
SP 200 hook cone: SP 400/450 tool, two bevels and temporary-ring removal
The cross-model tool reference does not establish hook interchange.
- Section 6.3.2 requires special tool 4234 890 5200, identified parenthetically as SP 400/SP 450. It comprises temporary ring (17) and sleeve (18). This is an explicit tool application on the SP 200 hook, not evidence that complete hooks, connector parts or all repair procedures interchange among these models.
- Put temporary ring (17) in the cone groove. Position the WHITE ring (16) with its BEVELLED SURFACE TOWARDS THE UNION NUT and press it on using sleeve (18). Remove temporary ring (17) from the cone groove again; it is an assembly aid, not a retained hook part.
- Place the other ring (16) in union nut (15), again with the BEVELLED SURFACE TOWARDS THE UNION NUT, and press on using sleeve (18). Screw on the hook and line it up. The two installed rings have the same drawing item (16); no separate order numbers or numeric torque are given.
- This tool pair is not the drive-tube coupling aid 4233 893 7000/4233 893 4902. Preserve the component-specific tool assignment despite the similar bevel-and-ring assembly sequence.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 5 · TI 34/2003, p. 21 · TI 34/2003, p. 25 — Drawing D; 6.3.2 complete; 8.2 illustration 22.
Part numbers (1)
- 4234 890 5200 — Hook-cone ring and sleeve toolSP 400 / SP 450-labelled tool explicitly required for SP 200 hook assembly · SP 200; specified procedure only
Service note · SP 200
SP 200 harness eyes: short end first, throttle cable free
Reverse the release order when fastening the two drive-tube eyes.
- Attach harness (2) to drive tube (3) using BOTH eyes (1), one on either side of the control-handle area as illustrated. The source does not specify measured attachment distances or a new harness order number.
- To dismantle each eye, undo the LONG end first, then the SHORT end. To assemble, fasten the SHORT end first, then wrap and fasten the LONG end as illustrated. The final long strap end folds around the tube over the short end; keep the eye/buckle accessible for the harness attachment.
- Explicit source caution: DO NOT TRAP THE THROTTLE CABLE UNDER THE BELT. The diagram’s strap position is not permission to clamp the cable. No belt tension, fastener torque or interchange with another model’s harness is established.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 22 — Section 7 complete including all four fastening illustrations.
No additional parts-table entry added.
Service note · SP 200
SP 200 service-tool set: all 22 illustrated tools, not every workshop aid
Kit membership is explicit; an illustrated tool is not a universal substitute.
- Section 8.1 states that ALL special tools illustrated in section 8.2 belong to service-tool set 4233 007 2200. The 22 illustration identities are retained below, with exact printed numbers. This records 2003 kit contents, not present availability, prices or a complete list of everything needed at the bench.
- Illustrated wrench openings are 47 mm (1300), 55 mm (1301), 38 mm (1302) and 36 mm (1303). Key 0900 has a 2.5 mm hexagon and 14 mm short leg. These are tool dimensions, not thread sizes, screw lengths or torques. No dimensions or fabrication tolerances are invented for the other illustrated tools.
- Figure 10 shows 4233 893 1502, but this bulletin gives no specific operation for that tool outside the illustration. Retain its kit membership and illustrated shape ONLY; do not assign it to a seal or bearing by similarity to 1500/1501. This is a source limitation, not an unreviewed local assertion.
- The 4234 890 5200 hook tool IS included because it is illustration 22, despite its different prefix and SP 400/SP 450 parenthetical in section 6.3.2. The separate 5910 893 2700 jaws, standard internal puller, ordinary wrenches, circlip pliers and hot-air blower are not listed among these 22 illustrations; no inclusion in this kit is asserted for them.
- The page 9 tool-number conflicts remain unresolved: 4133 versus 4233 893 1301 and 4233 894 versus 893 4902. This roster records the section 8 illustrations without silently correcting procedure text or certifying alternate tools. Copyright/technical-documentation footer supplies provenance, not an additional fitment or service assertion.
- SP 200 (series 4233) only. Drawing item numbers are not part order numbers. Local 1129/4134 groups contain exact SP 200 tool sheets; they do not extend these procedures to other models. No physical interchange test was performed.
Source: TI 34/2003, p. 23 · TI 34/2003, p. 24 · TI 34/2003, p. 25 — Sections 8.1/8.2 complete; all 22 illustrations.
Part numbers (23)
- 4233 007 2200 — Service-tool setIncludes all 22 illustrated tools · SP 200; specified procedure only
- 4233 890 2200 — Holding tool1; shaft/gearhead holding · SP 200; specified procedure only
- 4233 890 4400 — Drive-pinion puller2; drive-pinion extraction · SP 200; specified procedure only
- 4233 893 0900 — 2.5 mm key with 14 mm short leg3; thrust-plate screws · SP 200; specified procedure only
- 4233 893 1300 — 47 mm wrench4; front drive-tube union nut · SP 200; specified procedure only
- 4233 893 1301 — 55 mm wrench5; coupling union nut; page 9 conflicts · SP 200; specified procedure only
- 4233 893 1302 — 38 mm wrench6; coupling plug and counterhold · SP 200; specified procedure only
- 4233 893 1303 — 36 mm wrench7; pushrod housing joint · SP 200; specified procedure only
- 4233 893 1500 — Press tool8; specified gearhead bearings/pinion/plug · SP 200; specified procedure only
- 4233 893 1501 — Oil-seal press tool9; drive-pinion plug seal · SP 200; specified procedure only
- 4233 893 1502 — Illustrated cylindrical service tool10; specific operation not assigned in this bulletin · SP 200; specified procedure only
- 4233 893 2800 — Drive-pinion plug tool11; plug 20 · SP 200; specified procedure only
- 4233 893 4600 — Pin-end support12; use with 4601 · SP 200; specified procedure only
- 4233 893 4601 — Pin-end support13; use with 4600 · SP 200; specified procedure only
- 4233 893 4900 — Pushrod seal press sleeve14; oil seal 3 · SP 200; specified procedure only
- 4233 893 4901 — Hand-guard press sleeve15; hand guard 10 · SP 200; specified procedure only
- 4233 893 4902 — Drive-tube ring press sleeve16; page 9 first-reference 894 conflict retained · SP 200; specified procedure only
- 4233 893 5200 — Gear-housing clamping plate17; use with 8700 · SP 200; specified procedure only
- 4233 893 5400 — Bearing centering tool18; gearhead bearing assembly · SP 200; specified procedure only
- 4233 893 7000 — Temporary cone ring19; drive-tube coupling assembly · SP 200; specified procedure only
- 4233 893 8700 — Gear-housing clamping aid20; use with 5200 · SP 200; specified procedure only
- 4233 894 7700 — Tapered hand-guard guide21; carrier 12 · SP 200; specified procedure only
- 4234 890 5200 — Hook-cone ring and sleeve22; SP 400 / SP 450-labelled tool for SP 200 hook · SP 200; specified procedure only
Service note · SP 200
2005 SP 200 Loctite 243: coat half the overlapping thread
Clean both threads and protect thread flanks when reusing parts.
- The 2005 table names Loctite 243 threadlocker but gives NO STIHL ORDER NUMBER. Do not import the 2003 edition’s order number into this source. For new parts, remove grease, oil, dust and other dirt from both inside and outside threads with an appropriate solvent.
- Apply threadlocker over the full circumferential surface for a length equal to HALF the overlapping thread, starting at the beginning of the outside thread; then assemble and tighten the joint. This is not half of every screw’s total length.
- For disassembled parts, clean with a wire brush or similar without damaging the thread flanks, then follow the new-part preparation. This general section does not give a torque or cure time and does not approve Loctite 243 in joints specified for 326 or 638.
- These are TI40/2005 general SP 200 adhesive rules, not permission to use every adhesive on every joint. Use the component-specific drawings and procedures on pages 4–25 for each joint; the earlier TI34/2003 edition is not a substitute. The harvester is series 4233; exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. No physical interchange test was performed.
Source: TI 40/2005, p. 2 — 1 general material table;1.1.1 Loctite 243.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 Loctite 326: activator and less than 60 seconds working time
Coat two-thirds of the overlapping joint; do not confuse working time with full cure.
- The 2005 table names Loctite 326 fast-curing adhesive and Loctite 7649 activator, but gives NO STIHL ORDER NUMBERS for either. Activator 7649 promotes even curing including larger bonded joints; no historical order number is inferred from the earlier bulletin.
- For new parts, surfaces MAY be roughened with fine sandpaper to improve adhesion. Remove grease, oil, dust and other dirt with an appropriate solvent. Apply activator 7649 to ONE surface, or BOTH surfaces if the gap is large, and allow it to DRY as this edition states.
- Apply adhesive evenly over the full surface along TWO-THIRDS of the overlap, beginning at the start of the outward-facing joining surface. Slowly bring surfaces into contact and push/pull to distribute the adhesive evenly.
- Working time is LESS THAN 60 SECONDS. This is not a sixty-second minimum and not a full-cure specification. For reused parts, remove adhesive residues with sandpaper or similar, then proceed as for new parts. No numeric large-gap threshold or full-cure time is supplied.
- These are TI40/2005 general SP 200 adhesive rules, not permission to use every adhesive on every joint. Use the component-specific drawings and procedures on pages 4–25 for each joint; the earlier TI34/2003 edition is not a substitute. The harvester is series 4233; exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. No physical interchange test was performed.
Source: TI 40/2005, p. 2 — 1 material table;1.1.2 Loctite 326 and activator7649.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 Loctite 638: threads and bearing surfaces differ
Thread overlap gets half-length coverage; the bearing outer ring gets full coverage.
- Loctite 638 retaining compound is named WITHOUT a STIHL order number in this edition. For threaded joints, clean inside/outside threads with an appropriate solvent; apply evenly over the full thread surface for HALF the overlap length, starting at the outside-thread beginning, then assemble and tighten.
- For reused threaded parts, wire-brush or similarly clean the thread without damaging its flanks, then follow the new-part procedure. Do not transfer the two-thirds rule for Loctite 326 bonded surfaces to these threads.
- Under the printed Plain bearings heading, clean joining surfaces with solvent, coat the WHOLE OUTER RING of the bearing, insert into its housing and remove surplus adhesive with an appropriate solvent. Do not apply the half-thread-length rule to the bearing outer ring.
- For disassembled bearing joints, remove adhesive residue with sandpaper or similar, then follow the new-part sequence. No press fit, torque, bearing identity or cure time is established by this general section alone.
- These are TI40/2005 general SP 200 adhesive rules, not permission to use every adhesive on every joint. Use the component-specific drawings and procedures on pages 4–25 for each joint; the earlier TI34/2003 edition is not a substitute. The harvester is series 4233; exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. No physical interchange test was performed.
Source: TI 40/2005, p. 2 · TI 40/2005, p. 3 — 1.1.3 Loctite638;threaded joints and complete plain-bearing subsection.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 adhesive release: 600°C describes the hot-air jet
Heat the bond evenly and check frequently; it is not a component-temperature target.
- The bulletin says all adhesives used here can be released by heat and recommends an ELECTRIC hot-air blower producing a jet of at least 600°C (1100°F as printed). Those units are approximate, not an exact conversion (600°C is 1112°F). That number describes the air jet, NOT a required measured part temperature or a universal setting for unrelated materials.
- Its stated purpose is rapid heating of the bond without damaging other parts. Heat the bond area as evenly as possible. Slight crackling indicates loosening; check frequently whether the bond has released. Contact with hot parts can cause burns. No fixed dwell time, part-temperature setpoint or open-flame method is specified.
- Section 2 introduces workbench drawings A control handle, B drive tube assembly, C gearhead and D pushrod/hook. This index supplies no torque or order numbers; use the actual drawings and component procedures. The overview is not a complete repair procedure.
- These are TI40/2005 general SP 200 adhesive rules, not permission to use every adhesive on every joint. Use the component-specific drawings and procedures on pages 4–25 for each joint; the earlier TI34/2003 edition is not a substitute. The harvester is series 4233; exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. No physical interchange test was performed.
Source: TI 40/2005, p. 3 — 1.2 Removing adhesive;2 general drawing index.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 handle drawing A: separate 10 and 15 Nm fasteners
The scan supplies torques absent from the extracted page text.
- Drawing A, figure 411TI103 KN, shows two handle supports (1), tube (2), control handle (3) and plates (4). At EACH end the small plate-side screws are 10 Nm (89 in. lbs.), while the larger outer clamp fastener is 15 Nm (133 in. lbs.). Both imperial labels are INCH-POUNDS, not foot-pounds.
- The values apply to the arrowed connections in drawing A; they are not a blanket control-handle screw torque. The separate control-handle attachment screws mentioned in section 3.1 are not given a numerical torque here. No screw dimensions or order numbers are printed in this drawing.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 4 · TI 40/2005, p. 6 — handle drawing A: separate 10 and 15 Nm fasteners.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 control-handle removal and bonded support assembly
Loctite 326 belongs on the tube/support bond, not indiscriminately on screws.
- Unscrew handle-support screws (1), remove tube (2) and control handle (3); clamp the tube and heat one support bond using section 1.2 before removing that support. Slacken control-handle attachment screws and remove handle; remove the second support only if necessary.
- Attach the control handle to the tube. Prepare and apply Loctite 326 to tube (2) under section 1.1.2, press support (1) into place, LINE UP the support, then screw in and tighten support screws. Drawing A supplies the separate 10/15 Nm connections.
- Bond preparation requires clean surfaces, activator 7649 dried before adhesive, two-thirds overlap coverage and LESS THAN 60 SECONDS working time. Heat release uses the section 1.2 hot-air method; the 600°C (1100°F as printed) rating is the JET rating, not a target component temperature. Check loosening frequently and avoid contact with hot parts.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 2 · TI 40/2005, p. 3 · TI 40/2005, p. 4 · TI 40/2005, p. 6 — control-handle removal and bonded support assembly.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 drive-tube drawing B: plug torque and component order
Only plug (8) carries the 30 Nm callout.
- Drawing B (411TI104 KN) identifies engine-end tube (1), plugs (2), liner (3), drive shaft (4), coupling sleeve (7), threaded plug (8), O-ring (9), union nuts (10,12), rings (11), gearhead-end tube (13), liner (14), shaft (15), circlip (16), and clutch housing (28). The drawing is an assembly locator, not an orderable parts list.
- On EACH side of coupling sleeve (7), the exploded stack is ring/washer (5), bearing (6), ring/washer (5). The drawing does not label bearing type or give a material specification for (5); do not substitute a guessed bearing or omit a washer.
- The 30 Nm (22 ft. lbs.) arrow points to PLUG (8). It does NOT specify either union nut (10 or 12), nor drive-shaft retaining screw (18) on pages 7–8. The O-ring (9) belongs in plug (8), as section 4.2.2 illustrates.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 4 · TI 40/2005, p. 8 · TI 40/2005, p. 9 — drive-tube drawing B: plug torque and component order.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 gearhead drawing C: seven torque locations
Each torque belongs to its illustrated connection, not all adjacent fasteners.
- Drawing C (411TI105 KN) shows drive pinion (15) carrying two bearings (16) separated by spacer (17); circlip (18), seal (19) and threaded plug (20) complete that end. Plug (20): 10 Nm (89 in. lbs.). Drain screw plug (2) with seal (3): 9 Nm (80 in. lbs.).
- Clamp screw (7): 12 Nm (106 in. lbs.). Retaining screw (9): 20 Nm (15 ft. lbs.). Both illustrated thrust-plate nut/screw connections (5/4): 8 Nm (71 in. lbs.) EACH. Cover screws (26): 6 Nm (53 in. lbs.). The 20 Nm value is FOOT-POUNDS in its imperial equivalent; the other labels here are INCH-POUNDS.
- The gear housing (1), plug (8), thrust plates (6)/screws (4)/nuts (5), gear-bearing stack (10–14), connecting rod (22), needle bearings (23), washers (21) and circlips (24), cover (25) and screws (26) are separate exploded components. Washers flank the connecting-rod bearing interfaces; no bearing, seal or screw order number is provided by this drawing.
- These callouts are not a complete gearbox rebuild, adhesive map, oil quantity or alignment procedure; see sections 5.1–5.5 on pages 10–17 and their separate service notes. Do not infer a torque for pressed plug (8) or a separate fastener (6): (6) is the thrust plate, not a screw.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 5 · TI 40/2005, p. 13 · TI 40/2005, p. 14 — gearhead drawing C: seven torque locations.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 pushrod and hook drawing D: 55 versus 60 Nm joints
Similar-looking threaded joints have different specified torques.
- Drawing D (411TI106 KN) identifies pushrod (1), threaded housing (2), seal (3), circlip (4), forkhead (5), pin (6), washers (7), needle bearing (8), circlip (9), hand guard (10), washer (11), carrier (12), hook (13), rubber insert (14), union nut (15) and rings (16). The drawing supplies item locators, not STIHL order numbers.
- Pushrod-to-forkhead (5) joint: 55 Nm (41 ft. lbs.). Threaded housing (2): 60 Nm (44 ft. lbs.). Carrier (12): 55 Nm (41 ft. lbs.). All three imperial values are FOOT-POUNDS. Do not apply 60 Nm to every pushrod connection or assign a torque to union nut (15), which has no torque arrow.
- Washers (7) flank bearing (8) in the connector/pin assembly. Two rings (16) are illustrated between the hook/union-nut interface. The later assembly instructions govern orientation, adhesives and pressing; drawing review alone is not a completed pushrod/hook repair. This note does not supply the later component-repair procedures.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 5 · TI 40/2005, p. 18 · TI 40/2005, p. 20 · TI 40/2005, p. 21 — pushrod and hook drawing D: 55 versus 60 Nm joints.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 engine-end tube removal: shaft stays with engine
Removing the tube does not release the bolted drive shaft.
- To separate the front drive-tube assembly, slacken union nut (12) with 4233 893 1300 while steadying the gearhead-end tube with 4233 893 1302, then remove the front part from the machine.
- For engine-end tube (1), slacken the clutch-housing attachment screw and handle-support retainer screws, then pull out the tube. Drive shaft (4) is BOLTED TO THE CLUTCH DRUM and remains attached to the engine. Pry out plug (2), dismantle flexible liner (3), and assemble in reverse order. This is not the separate drive-shaft removal procedure.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 4 · TI 40/2005, p. 7 — engine-end tube removal: shaft stays with engine.
Part numbers (2)
- 4233 893 1300 — Union-nut toolSlacken nut12 · SP 200; TI40/2005 restrictions apply
- 4233 893 1302 — Steadying toolHold gearhead-end tube · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 drive-shaft removal and Loctite 638 reassembly
The source gives a 5 mm hex size, not a numeric shaft-screw torque.
- After engine-end tube removal, unscrew screws (17) and remove clutch housing (28). Hold shaft (4) with special tool 4233 890 2200. Release screw (18) adhesive with the section 1.2 hot-air method, then unscrew with a 5 mm hexagon socket key. Remove shaft, using a PLASTIC hammer and punch if necessary.
- Place shaft (4) in position, apply Loctite 638 to screw thread (18) under section 1.1.3, steady shaft with 4233 890 2200, and tighten using the 5 mm key. Complete assembly in reverse order. Thread preparation requires clean threads and adhesive over HALF the overlapping thread length, not the Loctite 326 two-thirds bond rule.
- No numerical tightening torque for screw (18) is printed here. Drawing B’s 30 Nm is plug (8), not this screw. Do not inherit a shaft-screw torque from a different edition or nearby gearbox drawing.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 2 · TI 40/2005, p. 3 · TI 40/2005, p. 4 · TI 40/2005, p. 7 · TI 40/2005, p. 8 — drive-shaft removal and Loctite 638 reassembly.
Part numbers (1)
- 4233 890 2200 — Drive-shaft holding toolSteady shaft during screw removal/fitting · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 swivel coupling removal, plug seal and tool-number conflict
Preserve the printed 4133/4233 tool discrepancy.
- Remove first circlip (11) with suitable pliers, remove union nut (12), then remove second circlip (11). Hold plug (8) with 4233 893 1302 and slacken/remove union nut (10) using 4233 893 1301. Heat the plug bond per section 1.2 and unscrew plug with 4233 893 1302. Drawing B gives the remaining exploded order.
- Place O-ring (9) IN plug (8). Apply Loctite 243 to plug threads under section 1.1.1, then screw in/tighten with 4233 893 1302; drawing B specifies 30 Nm (22 ft. lbs.) for plug (8). This is not a Loctite 638 plug joint.
- UNRESOLVED PRINTED TOOL CONFLICT: page 8 specifies 4233 893 1301 to remove union nut (10), but page 9 specifies 4133 893 1301 to tighten it. The original 2005 scans confirm both strings. Do not silently correct the prefix, order the disputed tool from this note alone, or claim proven interchange between the two numbers. No numerical nut (10) torque is specified here.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 2 · TI 40/2005, p. 3 · TI 40/2005, p. 4 · TI 40/2005, p. 8 · TI 40/2005, p. 9 — swivel coupling removal, plug seal and tool-number conflict.
Part numbers (3)
- 4233 893 1302 — Plug holding/turning toolHold and turn plug8 · SP 200; TI40/2005 restrictions apply
- 4233 893 1301 — Printed nut-removal toolPage8; conflicts with assembly prefix · SP 200; TI40/2005 restrictions apply
- 4133 893 1301 — Printed nut-assembly toolPage9 disputed prefix; not a verified substitute · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 swivel rings: bevels face the union nut
The temporary cone-groove ring must be removed after pressing.
- Put temporary tool ring (19), 4233 893 7000, in the cone groove. Place WHITE ring (11) with BEVELLED SURFACE TOWARDS THE UNION NUT and press on with sleeve (20), 4233 893 4902. REMOVE temporary ring (19) from the cone groove afterward.
- Place the other ring (11) into union nut (12), again with BEVELLED SURFACE TOWARDS THE UNION NUT, and press on using sleeve (20), 4233 893 4902. Complete assembly in reverse disassembly order. The temporary tool ring (19) is not a permanent coupling part.
- Section 4.2.1 calls (11) circlips; the assembly text explicitly calls one a white ring. Retain the source terms without assuming steel circlip material for every (11), assigning an order number or reversing the illustrated bevels.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 4 · TI 40/2005, p. 8 · TI 40/2005, p. 9 — swivel rings: bevels face the union nut.
Part numbers (2)
- 4233 893 7000 — Temporary cone-groove tool ringRemove after pressing first ring · SP 200; TI40/2005 restrictions apply
- 4233 893 4902 — Pressing sleevePress both rings11 · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 gearhead-end tube: liner and shaft removal
Reassembly still requires the separate gearhead alignment procedure.
- Slacken the gearhead attachment screw and remove gearhead. Pry out plug (2), remove flexible liner (14) and shaft (15); remove circlip (16), then pull shaft (15) out of liner (14). Assemble in reverse order.
- Section 4.3 explicitly requires gearhead alignment under section 5.5. Reverse assembly alone is NOT a completed alignment or readiness check. See the separate gearhead closure/alignment note and page17 for centered swivel, vertical gearhead and hook-down orientation; no oil quantity is inferred from this tube-removal section.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 4 · TI 40/2005, p. 9 — gearhead-end tube: liner and shaft removal.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 gear oil: first change and distinct 110/120 ml instructions
Routine-change and post-rebuild quantities are retained separately.
- First oil change after 20–25 HOURS operation; regularly AS REQUIRED thereafter. No fixed subsequent interval is printed. Turn tube until drain screw plug (2) faces down, catch oil in a suitable container, remove plug and seal (3), and drain completely. Slight warming with a hot-air blower may liquefy the oil; this is NOT the adhesive-release high-temperature procedure.
- Section 5.1 specifies APPROX. 110 ml (3.7 oz.) of 0781 313 7002, Klüber Synthetic oil GH 6, through the drain hole. Fit NEW seal 4233 649 0200 over the drain screw plug, screw in and tighten. Drawing C gives drain plug (2) 9 Nm (80 in. lbs.). Oil change can alternatively be done with gearbox disassembled.
- Section 5.5, after gearhead assembly, specifies 120 ml (4.1 oz.) of the SAME oil and a NEW 4233 649 0200 seal. The 10 ml difference is printed and NOT EXPLAINED. Preserve routine-change versus post-rebuild context; do not average the values, present a universal capacity, or invent a residual-oil explanation. The oz labels are source wording, not an oil-mass specification.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 5 · TI 40/2005, p. 10 · TI 40/2005, p. 17 — gear oil: first change and distinct 110/120 ml instructions.
Part numbers (2)
- 0781 313 7002 — Klüber Synthetic oil GH 6Gear oil; distinct110/120ml contexts · SP 200; TI40/2005 restrictions apply
- 4233 649 0200 — Drain-plug sealing ringReplace with new ring · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 gearbox removal and opening sequence
Drain oil before dismantling; release bonded retaining screw before cover work.
- Slacken clamp screw (7) and pull gearbox off drive tube; drain gear oil under section 5.1. Pry off plug (8), steady gearhead with 4233 890 2200, heat screw (9) bond under section 1.2 and unscrew using a 6 mm hex key. Remove screws (26) and cover (25).
- Remove circlips (24) and outer washers (21). Pry connecting rod (22) off EVENLY USING TWO SUITABLE TOOLS, then remove needle bearings (23) and inner washers (21). Remove spur bevel gear (14).
- Heat gear housing around bearing area; use a standard internal puller (27) to remove grooved ball bearing (13). Remove circlip (12), spacer ring (11), then grooved ball bearing (10). The drawing locates the stack; do not hammer through a retained circlip. No order number for generic puller (27) is supplied.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 3 · TI 40/2005, p. 5 · TI 40/2005, p. 10 · TI 40/2005, p. 11 — gearbox removal and opening sequence.
Part numbers (1)
- 4233 890 2200 — Gearhead holding toolSteady for retaining-screw removal · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 pushrod housing removal and refit: 2/18 numbering conflict
The pictured housing is identifiable despite inconsistent item labels.
- Clamp gear housing (1) using BOTH 4233 893 5200 and 4233 893 8700. Heat pushrod-housing bond using section 1.2; unscrew with 4233 893 1303. TILT the housing to separate it from the gear housing.
- For refit, clamp with the same two tools; tilt housing into gear housing, apply Loctite 243 to its threads under section 1.1.1, insert, then tighten using 4233 893 1303. Drawing D specifies 60 Nm (44 ft. lbs.) at housing (2). Do not substitute Loctite 638 from the adjacent pushrod/forkhead joints.
- ITEM-NUMBER CONFLICT: general drawing D and the unscrewing picture on page 12 label this pushrod housing (2), while the tilted view on page 12 and assembly on page 15 label it (18). Drawing C uses (18) for the unrelated drive-pinion circlip. The pictures identify the housing, but no order number or equivalence between those different components is inferred.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 2 · TI 40/2005, p. 3 · TI 40/2005, p. 5 · TI 40/2005, p. 12 · TI 40/2005, p. 15 — pushrod housing removal and refit: 2/18 numbering conflict.
Part numbers (3)
- 4233 893 5200 — Housing clamping fixtureUse with42338938700 · SP 200; TI40/2005 restrictions apply
- 4233 893 8700 — Housing clamping fixtureUse with42338935200 · SP 200; TI40/2005 restrictions apply
- 4233 893 1303 — Pushrod-housing wrenchUnscrew/tighten housing · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 drive-pinion extraction: separate 10 and 13 mm operations
Tool-screw engagement precedes pulling-nut operation.
- Unscrew threaded plug (20) with 4233 893 2800. Insert puller 4233 890 4400 into drive-tube clamp of gear housing (1). Use a 10 mm wrench to screw the TOOL SCREW into the drive-pinion thread; then use a 13 mm wrench to turn the TOOL NUT and pull out the pinion.
- Drawing C and figure 411TI010 KN give the disassembly order: threaded plug (20), oil seal (19), circlip (18), bearing (16), spacer (17), second bearing (16), pinion (15). The two wrench sizes are not fastener torques; no puller travel limit or bearing substitution is specified.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 5 · TI 40/2005, p. 12 · TI 40/2005, p. 13 — drive-pinion extraction: separate 10 and 13 mm operations.
Part numbers (2)
- 4233 893 2800 — Threaded-plug toolRemove plug20 · SP 200; TI40/2005 restrictions apply
- 4233 890 4400 — Drive-pinion puller10mm screw engagement then13mm nut extraction · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 thrust-plate removal and Loctite 638 refit
Nuts (5) are thrust-plate fasteners, not lubrication fittings.
- Heat adhesive on nuts (5) under section 1.2. Hold screws (4) with 4233 893 0900, a 2.5 mm hex key, and unscrew nuts (5). Refer to drawing C for remaining plate/fastener order.
- Position thrust plates (6), apply Loctite 638 to threads of screws (4) under section 1.1.3; steady nuts (5), then screw in and tighten screws (4). Drawing C marks these two nut/screw connections 8 Nm (71 in. lbs.) EACH. This is not a grease-point instruction or an 8 Nm value for the gearhead clamp screw (7).
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 2 · TI 40/2005, p. 3 · TI 40/2005, p. 5 · TI 40/2005, p. 13 · TI 40/2005, p. 14 — thrust-plate removal and Loctite 638 refit.
Part numbers (1)
- 4233 893 0900 — 2.5mm hexagon socket keyHold thrust-plate screws · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 drive-pinion and seal installation: different press tools
Tool 1500 fits the pinion; tool 1501 presses the seal into the plug.
- Reassemble drive pinion to drawing C: the two bearings (16) flank spacer (17), followed by circlip (18), oil seal (19) and threaded plug (20). Insert pinion into housing (1), then use 4233 893 1500 to press it into place.
- Use 4233 893 1501 to press oil seal (19) INTO PLUG (20), not directly into an unspecified housing bore. Insert plug into housing and tighten with 4233 893 2800; drawing C gives 10 Nm (89 in. lbs.). The section does not specify adhesive on plug (20); do not transfer the swivel-plug Loctite 243 rule here.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 5 · TI 40/2005, p. 14 — drive-pinion and seal installation: different press tools.
Part numbers (3)
- 4233 893 1500 — Pinion pressing toolPress pinion into gear housing · SP 200; TI40/2005 restrictions apply
- 4233 893 1501 — Oil-seal pressing toolPress seal19 into plug20 · SP 200; TI40/2005 restrictions apply
- 4233 893 2800 — Threaded-plug toolTighten plug20 · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 gear bearings and connecting rod: centered pressing order
Keep both washer sets and circlips in the connecting-rod stack.
- Insert centering tool 4233 893 5400 into gear housing (1). Press grooved ball bearing (10) in using 4233 893 1500, insert circlip (12), then insert spacer ring (11) and bearing (13) and press in using 4233 893 1500.
- Insert spur bevel gear (14). Fit inner washers (21) and needle bearings (23), mount connecting rod (22), then fit outer washers (21) and circlips (24), as figures 411TI031 KN and drawing C show. Do not omit a washer set or swap circlips (12) and (24).
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 5 · TI 40/2005, p. 15 · TI 40/2005, p. 16 — gear bearings and connecting rod: centered pressing order.
Part numbers (2)
- 4233 893 5400 — Gearhead centering toolCenter before bearing pressing · SP 200; TI40/2005 restrictions apply
- 4233 893 1500 — Bearing pressing toolPress bearings10and13 · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 gearhead closure and centered 135° alignment
Hook points down with the swivel centered, not at a travel end.
- Apply Dirko HT RED sealant 0783 830 2000 to gear-housing (1) edge, fit cover (25), and tighten screws (26), specified 6 Nm (53 in. lbs.) by drawing C. No sealant bead dimension or curing time is supplied.
- Steady gearhead with 4233 890 2200, apply Loctite 638 under section 1.1.3 to screw (9), and tighten: drawing C gives 20 Nm (15 ft. lbs.). Use 4233 893 1500 to press in plug (8). Do not apply threaded-plug (20) torque to this pressed plug.
- For section 5.5 attachment, fill 120 ml (4.1 oz.) 0781 313 7002 Klüber Synthetic oil GH 6 through the drain hole, fit NEW 4233 649 0200 seal over screw plug and tighten (9 Nm/80 in. lbs. in drawing C). The separate oil-change section gives approx.110 ml; difference remains unexplained.
- Push gearhead onto drive tube. Turn swivel coupling to CENTRE POSITION 135° of approximately270° total travel. Position gearhead VERTICALLY WITH HOOK POINTING DOWN, then tighten clamp screw (7):12 Nm (106 in. lbs.) in drawing C.135° is the center-of-travel position, not a request to tilt the gearhead135° away from vertical.
- TI40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 2 · TI 40/2005, p. 5 · TI 40/2005, p. 10 · TI 40/2005, p. 16 · TI 40/2005, p. 17 — gearhead closure and centered 135° alignment.
Part numbers (5)
- 0783 830 2000 — Dirko HT red sealantGear-housing cover edge · SP 200; TI40/2005 restrictions apply
- 4233 890 2200 — Holding toolSteady gearhead · SP 200; TI40/2005 restrictions apply
- 4233 893 1500 — Pressing toolPress plug8 · SP 200; TI40/2005 restrictions apply
- 0781 313 7002 — Klüber Synthetic oil GH 6120ml post-rebuild context · SP 200; TI40/2005 restrictions apply
- 4233 649 0200 — Drain-plug sealing ringNew ring on refit · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 pushrod disassembly: supported pin before heating
Carrier removal and forkhead removal require different clamping setups.
- First perform sections 5.2–5.3.3: remove gearbox, drain oil, open housing and remove pushrod/connecting rod. Unscrew hook (13); pry off hand guard (10), or cut it off with a sharp knife and remove. Remove snap ring (9), washers (7) and needle bearing (8).
- Fit tools 4233 893 4600 and 4233 893 4601 to the appropriate ends of pin (6), then clamp the forkhead AND tools as illustrated. Heat the pushrod (1) bond per section 1.2; use the appropriate open-end wrench on carrier (12) to unscrew it. Pull the housing over the free end of the pushrod and remove the forkhead tools.
- For the OTHER joint, clamp the free pushrod end with jaws 5910 893 2700, heat the bond, and unscrew forkhead (5) with the appropriate open-end wrench. Drawing D governs remaining housing-component disassembly. The source supplies no wrench size for these two joints.
- Heat release follows section 1.2: an electric hot-air blower with a jet rated at least 600°C (1100°F as printed), even bond heating and frequent loosening checks. The jet rating is NOT a target component temperature; hot parts can burn.
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 3 · TI 40/2005, p. 5 · TI 40/2005, p. 10 · TI 40/2005, p. 11 · TI 40/2005, p. 12 · TI 40/2005, p. 18 · TI 40/2005, p. 19 — pushrod disassembly: supported pin before heating.
Part numbers (3)
- 4233 893 4600 — Pin-end clamping supportUse with paired support · SP 200; TI40/2005 restrictions apply
- 4233 893 4601 — Other pin-end clamping supportUse with paired support · SP 200; TI40/2005 restrictions apply
- 5910 893 2700 — Clamping jawsHold free pushrod end for forkhead removal · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 pushrod seal installation and circlip
The seal is pressed with the pushrod inserted in its housing.
- Insert pushrod (1) into housing (2). Fit oil seal (3) and press it in with special tool 4233 893 4900, as figure 411 TI 020 KN shows. Fit circlip (4).
- Attach 4233 893 4600 and 4233 893 4601 to the appropriate ends of pin (6), then clamp forkhead and tools for threaded-joint assembly. The drawings give assembly placement, but no numerical seal depth or seal order number; do not invent either.
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 5 · TI 40/2005, p. 19 · TI 40/2005, p. 20 — pushrod seal installation and circlip.
Part numbers (3)
- 4233 893 4900 — Oil-seal pressing toolPress pushrod oil seal3 · SP 200; TI40/2005 restrictions apply
- 4233 893 4600 — Pin-end supportPaired forkhead clamping · SP 200; TI40/2005 restrictions apply
- 4233 893 4601 — Pin-end supportPaired forkhead clamping · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 pushrod joints: Loctite 638 and printed item conflict
Two 55 Nm joints are separate from the 60 Nm housing connection.
- Apply Loctite 638 to forkhead thread (5) under section 1.1.3 and screw in the pushrod by hand. Fit the pushrod housing over its free end. Place washer (11) on carrier (12); apply Loctite 638 to carrier threads, insert by hand and tighten with the appropriate wrench.
- PRINTED ITEM-NUMBER CONFLICT: page 20 says “Screw in the pushrod (5) by hand, ” while its own figure 411 TI 023 KN and drawing D label the tube/pushrod (1) and forkhead (5). Preserve the mismatch; it is not evidence of a second pushrod or permission to swap components.
- Drawing D specifies 55 Nm (41 ft. lbs.) at the tube/forkhead joint and 55 Nm (41 ft. lbs.) at carrier (12). Housing (2) has a DISTINCT 60 Nm (44 ft. lbs.) callout. Page 20 explicitly says hand-start then wrench-tighten the carrier; do not treat hand-starting as final torque or transfer housing torque to either end joint.
- Loctite 638 threaded-joint preparation: clean inner/outer threads; cover HALF the overlapping outside-thread length evenly. Previously used threads are cleaned with a wire brush or similar without damaging flanks. The housing-to-gearhead Loctite 243 instruction in section 5.4.3 is separate, not replaced by 638.
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 2 · TI 40/2005, p. 5 · TI 40/2005, p. 15 · TI 40/2005, p. 20 — pushrod joints: Loctite 638 and printed item conflict.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 pushrod bearing stack and hand-guard fitting
Gearbox assembly and alignment are required before the final hook installation.
- Fit washers (7), needle bearing (8) and snap ring (9). The figure shows a washer on EACH side of the bearing, followed by the snap ring at the pin end. Then perform sections 5.4.3–5.5: fit pushrod housing, assemble gearbox, close/fill it and align the gearhead; the local gearhead notes retain those steps and their oil-volume/item-number conflicts.
- Fit guide tool 4233 894 7700 OVER carrier (12) and press on hand guard (10) using 4233 893 4901; then screw on the hook. The cone-shaped guide and pressing sleeve are tools, not permanent hook components. No separate hand-guard adhesive or numerical pressing depth is specified.
- The referenced alignment uses the swivel centre position (135°) and vertical machine with hook pointing down. The gearbox rebuild calls for 120 ml oil; the routine oil change separately calls for approx. 110 ml. Their difference is NOT EXPLAINED by the source and is not a universal fill quantity.
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 5 · TI 40/2005, p. 15 · TI 40/2005, p. 16 · TI 40/2005, p. 17 · TI 40/2005, p. 20 · TI 40/2005, p. 25 — pushrod bearing stack and hand-guard fitting.
Part numbers (2)
- 4233 894 7700 — Hand-guard guide coneFit over carrier12 · SP 200; TI40/2005 restrictions apply
- 4233 893 4901 — Hand-guard pressing sleevePress hand guard10 · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 hook rubber-insert replacement and alignment
The insert is replaceable without inventing a part number.
- Unscrew the hook. Pry rubber insert (14) out of hook (13) and fit a NEW rubber insert. Screw the hook back on and line it up.
- Drawing D and section 6.3 identify the components, but give no rubber-insert order number, hardness, adhesive or hook-tightening torque. The adjacent 55 Nm callout belongs to carrier (12), not the hook or union nut (15).
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 5 · TI 40/2005, p. 21 — hook rubber-insert replacement and alignment.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 hook cone connector: remove the temporary ring
Both permanent rings face the union nut with their bevels.
- Tool 4234 890 5200 comprises ring (17) and sleeve (18). Place temporary ring (17) in the cone groove. Place WHITE ring (16) with BEVELLED SURFACE TOWARDS THE UNION NUT and press on with sleeve (18). REMOVE temporary ring (17) from the groove afterward.
- Place the other ring (16) into union nut (15), again with BEVELLED SURFACE TOWARDS THE UNION NUT, and press on with sleeve (18). Screw on the hook and line it up. Temporary tool ring (17) is NOT a permanent third connector ring.
- This is the hook-end kit 4234 890 5200. Do not silently substitute the swivel-coupling tools 4233 893 7000/4902 from section 4.2.2 merely because the operations resemble one another. No numerical union-nut torque is printed here.
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 5 · TI 40/2005, p. 21 · TI 40/2005, p. 25 — hook cone connector: remove the temporary ring.
Part numbers (1)
- 4234 890 5200 — Hook cone connector assembly kitRing17 and sleeve18 · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 harness eyes: short end first on assembly
Do not trap the throttle cable under either attachment belt.
- Attach harness (2) to drive tube (3) using TWO eyes (1), positioned on opposite sides of the handle assembly as figure 411 TI 041 KN shows. This is not a single-eye suspension instruction.
- To disassemble an eye, undo the LONG end first, then the SHORT end. To assemble, fasten the SHORT end first, then the LONG end, following the illustrated fold-back direction.
- CAUTION: do NOT trap the throttle cable under the belt. This routing condition applies during eye fastening; it is not waived after the long end is closed. The page supplies no numerical eye spacing or belt-tightening torque.
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 22 — harness eyes: short end first on assembly.
No additional parts-table entry added.
Service note · SP 200
2005 SP 200 service-tool set: 22 illustrated tools
The illustrated set is not a claim that every repair supply is included.
- Section 8.1 states that the tools illustrated in 8.2 are included in service-tool set 4233 007 2200. Pages 23–25 show 22 numbered illustrations; the last is the two-piece hook kit 4234 890 5200. Illustration numbers are not order numbers or necessarily counts of individual pieces.
- Page 23 illustrations 1/2 identify holding tool 4233 890 2200 and puller 4233 890 4400. The remaining illustrations identify the keys, sleeves, supports, guide and ring recorded in the companion tool notes.
- Clamping jaws 5910 893 2700 are required by page 19 but are NOT among the 22 illustrated tools. Set membership does not promise every general-purpose tool, adhesive, oil or replacement component needed for the repairs, nor present-day availability.
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 19 · TI 40/2005, p. 23 · TI 40/2005, p. 24 · TI 40/2005, p. 25 — service-tool set: 22 illustrated tools.
Part numbers (4)
- 4233 007 2200 — Service-tool setContains tools illustrated in section8.2 · SP 200; TI40/2005 restrictions apply
- 4233 890 2200 — Holding toolIllustration1 · SP 200; TI40/2005 restrictions apply
- 4233 890 4400 — PullerIllustration2 · SP 200; TI40/2005 restrictions apply
- 5910 893 2700 — Clamping jawsRequired by page19; not illustrated set membership · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 tool dimensions: key leg versus wrench openings
Tool dimensions are not fastener torques or fabrication drawings.
- Illustration 3: key 4233 893 0900 has a 2.5 mm hex cross-section and a 14 mm short-leg dimension. The 14 mm label is NOT its across-flats size.
- Illustrations 4–7 show opening widths: 4233 893 1300 = 47 mm; 4233 893 1301 = 55 mm; 4233 893 1302 = 38 mm; 4233 893 1303 = 36 mm. These dimensions identify the illustrated tools, not an instruction that any generic wrench provides the same access or support.
- Page 23 prints 4233 893 1301, agreeing with the page 8 removal instruction; page 9 assembly prints 4133 893 1301. The unresolved 4133/4233 prefix conflict remains documented; this additional illustration is evidence, not an official correction or proof of interchangeable tools. These illustrations supply no full manufacturing tolerances or material specification.
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 8 · TI 40/2005, p. 9 · TI 40/2005, p. 23 · TI 40/2005, p. 24 — tool dimensions: key leg versus wrench openings.
Part numbers (6)
- 4233 893 0900 — 2.5mm key14mm short leg · SP 200; TI40/2005 restrictions apply
- 4233 893 1300 — 47mm wrenchIllustration4 · SP 200; TI40/2005 restrictions apply
- 4233 893 1301 — 55mm wrenchIllustration5; disputed prefix elsewhere · SP 200; TI40/2005 restrictions apply
- 4233 893 1302 — 38mm wrenchIllustration6 · SP 200; TI40/2005 restrictions apply
- 4233 893 1303 — 36mm wrenchIllustration7 · SP 200; TI40/2005 restrictions apply
- 4133 893 1301 — Disputed assembly-tool prefixPage9 only; not corrected silently · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 service-tool illustrations 8–14: distinct pressing profiles
Similar cylindrical tools retain separate identities.
- Page 24 illustrations 8/9/10 identify 4233 893 1500, 4233 893 1501 and 4233 893 1502. Their depicted end profiles differ: 1500 has a recessed annular end, 1501 a protruding pilot, and 1502 an annular face. The pictures provide no numerical profile dimensions or substitution approval.
- Illustration 11 shows slotted-end tool 4233 893 2800. Illustrations 12/13 show paired pin supports 4233 893 4600/4601; illustration 14 shows oil-seal pressing sleeve 4233 893 4900. The paired supports are different shapes, not duplicate interchangeable pieces. Their use is governed by the relevant disassembly/assembly steps, not inferred from appearance alone.
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 24 — service-tool illustrations 8–14: distinct pressing profiles.
Part numbers (7)
- 4233 893 1500 — Recessed-end toolSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 1501 — Pilot-ended toolSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 1502 — Annular-ended toolSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 2800 — Slotted-end toolSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 4600 — Pin supportSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 4601 — Paired pin supportSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 4900 — Oil-seal pressing sleeveSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
Service note · SP 200
2005 SP 200 service-tool illustrations 15–22: sleeves, ring and guide
Tool geometry does not establish interchange or extra kit contents.
- Page 25 illustrations 15/16 identify sleeves 4233 893 4901 and 4233 893 4902; 17 identifies plate 4233 893 5200; 18 identifies shouldered tool 4233 893 5400. These are separate identities, not a sleeve substitution list.
- Illustrations 19/20/21 identify split ring 4233 893 7000, stepped tool 4233 893 8700 and cone guide 4233 894 7700. Illustration 22 shows 4234 890 5200 as sleeve PLUS separate split ring, consistent with the page 21 hook assembly. Do not leave temporary tool rings in the machine.
- The footer identifies Andreas Stihl AG & Co. KG, 2005, Technical Documentation D1/MTK-na. It is provenance, not a new serial cutoff, revision date or redistribution authorization. Original notices remain with the retained scan.
- TI 40/2005 applies to the SP 200 special harvester, series 4233. Exact SP 200 tool sheets in local groups 1129/4134 are navigation anchors, not applicability to other machines. Drawing item numbers are not order numbers. No physical interchange test was performed.
Source: TI 40/2005, p. 21 · TI 40/2005, p. 23 · TI 40/2005, p. 25 — service-tool illustrations 15–22: sleeves, ring and guide.
Part numbers (8)
- 4233 893 4901 — Hand-guard sleeveSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 4902 — Coupling-ring sleeveSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 5200 — PlateSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 5400 — Shouldered toolSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 7000 — Split tool ringSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 893 8700 — Stepped toolSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4233 894 7700 — Cone guideSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
- 4234 890 5200 — Hook sleeve-and-ring kitSection8.2 illustrated identity · SP 200; TI40/2005 restrictions apply
Wrong number or missing part for the SP 200? Report a correction →