← FR 125, FR 135, FR 145 · FS 108 · FR 108

Stihl 4135 · Section G · 7 of 14 · 37 parts

Carburetor C1Q-SK7 USA

Fits FS 108.

Parts diagrams →

Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111212121313141516171819220212223242525262728293303132333435456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (37)

PosPart numberDescriptionQty
1 4116 121 5100 Inlet needle 1
2 1120 122 3004 Spring 1
3 1120 121 9200 Spindle 1
4 1125 121 5000 Inlet control lever 1
5 1120 122 6600 Collar screw 1
6 4132 121 5400 Valve jet 1
7 4129 121 0700 Cup plug 1
8 4129 129 0902 Gasket 1
9 4129 121 4700 Metering diaphragm 1
10 1129 121 0800 End cover 1
11 4132 122 6600 Collar screw 2
12 1120 122 3005 Spring 3
13 4135 121 8600 Washer Fitment / change note → 2
14 4135 122 6700 High speed adjustment screw Fitment / change note → 1
15 4135 122 6800 Low speed adjustment screw Fitment / change note → 1
16 4135 121 2700 Cap Fitment / change note → 1
17 4135 121 2701 Cap Fitment / change note → 1
18 4129 122 6300 Idle speed adjustment screw 1
19 1123 122 3000 Spring 1
20 4132 120 7101 Throttle shaft with lever 1
21 4119 121 8900 Pin 1
22 1120 122 9000 E-clip 1
23 1125 122 9001 E-clip 1
24 4129 121 3300 Throttle shutter 1
25 1125 122 7403 Round head screw 2
26 1123 121 7800 Strainer 1
27 1129 121 4800 Pump diaphragm 1
28 1123 129 0905 Gasket 1
29 4129 121 0800 End cover 1
30 1120 122 7800 Oval head screw 1
31 4119 122 3002 Spring 1
32 4119 122 4200 Ball 1
33 4132 121 3000 Choke shaft 1
34 4119 121 2901 Choke shutter 1
35 1125 121 0700 Cup plug Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 4135 120 0601 NLA Carburetor C1Q-SK7 Fitment / change note → 1
— 4134 007 1060 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 108 / FR 108

FS/FR108 emissions carburetor: cap colors and 90-degree limit

C1Q-SK7 has changed screws and body; white is low speed, red is high speed. Workshop and user adjustments are distinct.

  • TI15/1995 introduces emissions-related carburetors for FS 108 and FR 108, series 4135, referring to TI41/1994 and TI47/1994 for background. It changes the H and L screws, limiter caps and carburetor body. Original and new screws have DIFFERENT THREAD PROFILE AND LEAD and differently shaped heads; do not infer screw interchange. A washer sits between each screw head and spring (354TI001).
  • WHITE cap = LOW SPEED (L); RED cap = HIGH SPEED (H). The installed molded stops limit adjustment to 1/4 turn / 90 degrees (354TI002). This is user travel with caps fixed, NOT the uncapped workshop basic setting.
  • Factory and service-shop adjustment is performed WITHOUT caps using the specified small screwdriver. In normal operation the caps are firmly seated and the STIHL carburetor screwdriver turns the screws through them. Forcible removal destroys or makes caps unserviceable.
  • The TI attributes the limited range to preserving emissions limits and engine power while allowing correction for running behavior, altitude, humidity and ambient temperature. That is a historical vendor design claim, not independently measured emissions compliance or a current legal claim. No numerical emission threshold or serial cutoff is provided.
  • Historical TI guidance only, specific to FS 108 / FR 108 and the stated carburetor version. Exact-model IPL links are navigation, not unrestricted interchange. No hardware operation was performed.

Source: TI 15/1995, p. 1 · TI 15/1995, p. 2 · TI 15/1995, p. 3 — Complete bulletin: emissions carburetor and shroud; all text, figures, flowchart, tables and footer.

No additional parts-table entry added.

Service note · FS 108 / FR 108

FS/FR108 C1Q-SK7 parts: two washers and sealing-plate change

Carburetor 4135 120 0601 includes items 1–7; the sealing plate also changes on non-emissions C1Q-SK5.

  • The complete C1Q-SK7 4135 120 0601 INCLUDES ITEMS 1 THROUGH 7 in 354TI003. Item 3 is TWO washers 4135 121 8600: one for H and one for L, not two on each screw. Item 2 is the red H cap; item 5 is the white L cap. Replacement carburetors are supplied with caps LOOSE; caps are pushed on only after adjustment.
  • Item 6 sealing plate 1125 121 0700 will also be used in future on non-emissions C1Q-SK5 IN PLACE OF 4129 121 0701. This is a targeted sealing-plate change, not authorization to transplant the changed adjusting screws or the complete emissions configuration.
  • The TI says all other parts are as C1Q-SK5. The later exact-model G C1Q-SK7 IPL and F C1Q-SK5 IPL both show 1125 121 0700 as cup plug, but their valve jets differ: G key 6 is 4132 121 5400 versus F key 6 4135 121 5400. This source/catalog discrepancy is retained; do not flatten the TI statement into unrestricted interchange. The TI lever 4222 123 7300 appears in the later exact-model air-filter sheet at key 9 rather than the G carburetor roster. Later catalog absence/NLA is not proof of historical absence or current availability.
  • Historical TI guidance only, specific to FS 108 / FR 108 and the stated carburetor version. Exact-model IPL links are navigation, not unrestricted interchange. No hardware operation was performed.

Source: TI 15/1995, p. 2 · TI 15/1995, p. 3 — Complete bulletin: emissions carburetor and shroud; all text, figures, flowchart, tables and footer.

Part numbers (9)
  • 4135 120 0601 — Carburetor C1Q-SK7includes items 1–7 · FS 108; FR 108
  • 4135 122 6700 — High speed screw, item 1new · FS 108; FR 108
  • 4135 121 2700 — Red limiter cap, item 2high speed H · FS 108; FR 108
  • 4135 121 8600 — Washer, item 3two total, one per adjusting screw · FS 108; FR 108
  • 4135 122 6800 — Low speed screw, item 4new · FS 108; FR 108
  • 4135 121 2701 — White limiter cap, item 5low speed L · FS 108; FR 108
  • 1125 121 0700 — Sealing plate, item 6new; future C1Q-SK5 replacement · FS 108; FR 108
  • 4222 123 7300 — Lever, item 7included · FS 108; FR 108
  • 4129 121 0701 — Original C1Q-SK5 sealing platereplaced in future · FS 108; FR 108

Service note · FS 108 / FR 108

FS/FR108 limiter tools: retain the drawing dimensions

Uncapped adjustment and cap installation require different screwdriver-tip geometries.

  • The TI says repairs and adjustment can be performed ONLY IF the specified tools are available. Uncapped adjustment uses a standard commercial screwdriver. Figure 002TI005 specifies blade length AT LEAST 60 mm, printed alongside 2 inches, and a 2 mm / 0.078-inch tip. The extracted body drops the greater-than-or-equal sign. The 60 mm and 2-inch labels are not exact conversions; preserve the printed metric minimum rather than silently equating them.
  • Figure 002TI006 gives a workshop-made cap-installing tool from a commercial screwdriver: blade length AT LEAST 75 mm (printed 3 inches); end-view width 5.6 mm (7/32 inch), end-view central thickness 1 mm (0.04 inch), side projection 1.5 mm (1/16 inch), and reduced end width 4 mm (5/32 inch). Read these dimensions with the original end/side/top views; this is not a generic 5.6 mm flat-blade specification. No fabrication tolerance, material specification or installation force is given.
  • Historical TI guidance only, specific to FS 108 / FR 108 and the stated carburetor version. Exact-model IPL links are navigation, not unrestricted interchange. No hardware operation was performed.

Source: TI 15/1995, p. 3 · TI 15/1995, p. 4 — Complete bulletin: emissions carburetor and shroud; all text, figures, flowchart, tables and footer.

No additional parts-table entry added.

Service note · FS 108 / FR 108

FS/FR108 adjusting screws: new caps after removal

Remove screw with washer and spring; carefully seat, adjust, then fit fresh caps.

  • Section 1.2.2.1 / 354TI004: pull the cap off; this DESTROYS THE CAP and a NEW CAP MUST BE USED. Remove adjusting screw (2), washer (3) and spring (4) together. Figure 354TI005 places spring on the inward side and washer between spring and screw head.
  • Section 1.2.2.2 / 354TI006: carefully screw home the screw with washer and spring as far as it will go. No seating torque is supplied. Perform the complete service adjustment before fixing caps. Fully seated caps CANNOT BE REUSED after pulling off.
  • Section 1.2.3.6: SHUT DOWN THE ENGINE before loosely fitting both caps with stops oriented EXACTLY AS FIGURE 354TI010 (arrows at the inner upper/lower stop positions), then carefully press over the screws with the installing tool (002TI011). Cap orientation is source-diagram-specific; no invented angular clocking value or pressing force. Observe white L / red H assignment and the subsequent running-behavior recheck.
  • Historical TI guidance only, specific to FS 108 / FR 108 and the stated carburetor version. Exact-model IPL links are navigation, not unrestricted interchange. No hardware operation was performed.

Source: TI 15/1995, p. 4 · TI 15/1995, p. 5 · TI 15/1995, p. 8 — Complete bulletin: emissions carburetor and shroud; all text, figures, flowchart, tables and footer.

No additional parts-table entry added.

Service note · FS 108 / FR 108

FS/FR108 service adjustment: preserve both retry loops

The flowchart checks behavior before and after fixing caps; post-cap failure requires removing both caps.

  • Page 5 requires the page 6 flowchart: preparations 1.2.3.1 → basic setting 1.2.3.2 → idle speed 1.2.3.3 → full-load speed 1.2.3.4 → running-behavior check 1.2.3.5. Before caps are fixed, a NO result returns to IDLE SPEED, not directly to completion.
  • Only a YES result allows fixing caps (1.2.3.6). Then check running behavior AGAIN. A NO result here requires removal of BOTH caps (1.2.2.1) and returns to IDLE SPEED. Removed seated caps are destroyed and require replacement. A YES after cap fixing ends adjustment. No maximum retry count is stated.
  • Running-behavior check means opening the throttle several times to verify smooth acceleration AND smooth idling. No numeric acceleration threshold is supplied.
  • Unresolved internal sequence conflict: page 6 puts IDLE adjustment before FULL-LOAD adjustment after basic setting; page 7 basic-setting text says start the engine and carry out FULL-LOAD setting, referring to 1.2.3.4. Both are preserved; this review does not silently reconcile them or authorize a hardware procedure.
  • Historical TI guidance only, specific to FS 108 / FR 108 and the stated carburetor version. Exact-model IPL links are navigation, not unrestricted interchange. No hardware operation was performed.

Source: TI 15/1995, p. 5 · TI 15/1995, p. 6 · TI 15/1995, p. 7 · TI 15/1995, p. 8 — Complete bulletin: emissions carburetor and shroud; all text, figures, flowchart, tables and footer.

No additional parts-table entry added.

Service note · FS 108 / FR 108

FS/FR108 workshop settings: 2800 rpm idle and loaded-speed method

Two-turn uncapped basic setting is not the capped user setting; loaded adjustment needs a tachometer and specified cutting head.

  • Service preparation: engine speeds MUST be checked with a TACHOMETER. Check/clean air filter; inspect spark-arresting screen and clean or replace as needed. Mount STIHL AutoCut or Polymatic head with lines extending to the line-limiting blade on the deflector. No particular head part number or line diameter is supplied.
  • Uncapped basic setting: from carefully seated screws open BOTH H AND L TWO FULL TURNS, then start the engine. The following full-load cross-reference differs from the flowchart ordering; see the service-flow note. This is not permission to force capped screws two turns.
  • Idle adjustment: use 2 mm (printed 5/64 inch) tip, find maximum idle speed with L, then turn L COUNTERCLOCKWISE until speed drops ABOUT 300 rpm. Set 2,800 rpm with the separate idle-speed screw LD. The 300 rpm value is a drop, not the idle target; H, L and LD are distinct controls.
  • Full-load adjustment: at full throttle turn H carefully CLOCKWISE until no further speed increase occurs WITHIN 6,500–8,500 rpm. If outside that range, vary cutting-line length until correct. Then turn H COUNTERCLOCKWISE until speed falls ABOUT 100 rpm. This is a loaded-head tuning method, NOT a universal no-load rev limit, fixed target of 8,500 rpm, or metal-blade procedure. Recheck behavior and cap sequence as documented.
  • Historical TI guidance only, specific to FS 108 / FR 108 and the stated carburetor version. Exact-model IPL links are navigation, not unrestricted interchange. No hardware operation was performed.

Source: TI 15/1995, p. 7 · TI 15/1995, p. 8 — Complete bulletin: emissions carburetor and shroud; all text, figures, flowchart, tables and footer.

No additional parts-table entry added.

Service note · FS 108 / FR 108

FS/FR108 user settings: richer stops and metal-tool restriction

Capped owner adjustment is distinct from workshop adjustment; do not lean H without a tachometer.

  • The TI states these instructions match the owner manual Adjusting the Carburetor chapter; the chapter is reproduced here, so no absent manual is needed to interpret this self-contained excerpt. Whole-manual equivalence and acceptance are NOT established. Check/clean air filter and spark-arresting screen, mount cutting head and trim lines to the deflector line-limiting blade.
  • A — Standard setting: if readjusting from scratch, start engine and turn H and L COUNTERCLOCKWISE (richer) as far as limiter caps allow. WITHOUT A TACHOMETER DO NOT SET H LEANER than this standard setting. B — warm up about ONE MINUTE AT FULL THROTTLE, then return to idle. These are historical printed instructions, not an unattended operation request.
  • C — idle: L corrections usually require subsequent LD correction. If the cutting tool turns at idle, turn LD COUNTERCLOCKWISE until it stops, then back off ABOUT ANOTHER HALF TURN. Do not confuse that half turn of LD with the capped H/L 90-degree travel.
  • D — maximum speed WITH CUTTING HEAD: use a tachometer to find highest possible speed with H, then turn H 1/8 turn COUNTERCLOCKWISE (richer) OR AS FAR AS THE STOP. WITH METAL CUTTING TOOL THE SETTING MUST NOT BE CHANGED. Retain the warning about lack of lubrication and overheating causing engine damage. No numeric maximum speed is printed in this user section; do not import the workshop loaded-speed range as its no-load specification.
  • Historical TI guidance only, specific to FS 108 / FR 108 and the stated carburetor version. Exact-model IPL links are navigation, not unrestricted interchange. No hardware operation was performed.

Source: TI 15/1995, p. 8 · TI 15/1995, p. 9 — Complete bulletin: emissions carburetor and shroud; all text, figures, flowchart, tables and footer.

No additional parts-table entry added.

Service note · FS 108 / FR 108

FS/FR108 idle faults: stationary cutting tool and richer correction

LD corrects idle stopping; erratic idle/acceleration calls for richer H and L within the stops.

  • If the engine stops while idling, turn LD CLOCKWISE until it runs smoothly; the cutting tool or blade MUST NOT ROTATE. This does not override the tool-stop check and counterclockwise correction in user step C.
  • For erratic idling or poor acceleration turn BOTH H AND L COUNTERCLOCKWISE (richer) as far as the caps allow; then carry out step C (idle setting). If behavior does not improve, repeat A THROUGH D, retaining the tachometer requirement, cap stops and metal-cutting-tool restriction. No permission to remove caps, force stops or lean beyond the standard setting without a tachometer is given.
  • Historical TI guidance only, specific to FS 108 / FR 108 and the stated carburetor version. Exact-model IPL links are navigation, not unrestricted interchange. No hardware operation was performed.

Source: TI 15/1995, p. 9 · TI 15/1995, p. 10 — Complete bulletin: emissions carburetor and shroud; all text, figures, flowchart, tables and footer.

No additional parts-table entry added.

Wrong number or missing part for the FS 108? Report a correction →