Stihl 4135 · Section J · 9 of 14 · 33 parts
Two-handed handle bar
Fits FS 108.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (33)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 791 7610 | Support | 1 |
| 2 | 4133 791 0900 | Clamp | 1 |
| 3 | 4133 791 0905 | Clamp | 1 |
| 4 | 9022 341 1350 | Spline screw IS-M6x25 | 6 |
| 5 | 4126 791 1700 | Two-handed handle bar | 1 |
| 6 | 4126 791 0801 | Handle molding, outer | 1 |
| 7 | 4126 182 4506 | Torsion spring | 1 |
| 8 | 4126 182 0800 | Lockout lever | 1 |
| 9 | 4126 182 6210 | Collar screw | 1 |
| 10 | 4126 791 0811 | Handle molding, inner | 1 |
| 11 | 4126 182 1700 | Slide control | 1 |
| 12 | 4126 182 4700 | Detent spring | 1 |
| 13 | 4126 182 6200 | Collar screw | 1 |
| 14 | 4126 442 1600 | Contact spring | 1 |
| 15 | 4126 182 6210 | Collar screw | 1 |
| 16 | 4126 182 4500 | Torsion spring | 1 |
| 17 | 4126 182 1001 | Throttle trigger | 1 |
| 18 | 4126 442 1610 | Contact spring | 1 |
| 19 | 9099 021 1890 | Self-tapping screw 2.9x25 | 5 |
| 20 | 9210 260 0700 | Hexagon nut M5 | 2 |
| 21 | 9022 346 1070 | Spline screw IS-M5x30 | 3 |
| 22 | 4135 180 1100 | Throttle cable | 1 |
| 23 | not sold separately | Lead 970 mm / 38.2'' not available as a separate item | 1 |
| 24 | not sold separately | Lead 1020 mm / 40.2'' not available as a separate item | 1 |
| 25 | 0751 030 8953 NLA | Terminal socket 4.8-1 no longer available from factory | 2 |
| 26 | 0751 030 8470 | Grommet no longer available from factory | 2 |
| 27 | 0751 030 8474 | Terminal socket 4.8-1 no longer available from factory | 2 |
| 28 | 0751 030 8460 | Grommet no longer available from factory | 2 |
| 29 | 4203 711 7201 | Hose 960 mm / 37 13/16'' | 1 |
| 30 | 4126 790 1350 | Handle, left | 1 |
| 31 | 9099 021 1890 | Self-tapping screw 2.9x25 | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4126 790 1303 | Control handle | 1 |
| — | 0751 010 1110 | Lead 10 m / 33' not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 88 / FS 108
FS 88 / 108: filter stack, controls and isolation
Foam sits between the cover and felt; no tool is needed for the filter cover.
- Diaphragm carburetor has a thermally insulated cylinder mounting. Air filter diagram: cover 3, foam element 1, felt element 2 toward the engine. Cover removal/refitting needs no tools. Fuel capacity 0.69 l (1.45 US pt); no mixture ratio or filter-part number printed here.
- Control layout is described as FS 72, 74, 76, 86 and 106: throttle trigger lock 4, trigger 5, slide control 6. Starting-throttle, run and stop positions are selected with one hand. Illustration labels STOP, I and START; no bypass of the trigger lock is authorized.
- Clutch shoes have linings and pivot on the flywheel. AV layout is described as FS 74/76, isolating vibration mainly to the engine. These comparisons do not establish universal control, clutch or AV-rubber interchange.
- Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.
Source: TI 37/1994, p. 1 · TI 37/1994, p. 3 · TI 37/1994, p. 5 — FS 88 / 108: filter stack, controls and isolation.
No additional parts-table entry added.
Service note · FS 88 / FS 108
FS 88 / 108: handle, drive and generic tightening torques
Specific rows override generic all-other M4/M5 entries.
- Pairs are Nm / lbf.ft. Self-tapping B2.9x25, two halves of control handle and left handle: 2.0 / 1.5. IS-M 5x30 control handle and left handle to bike handle: 3.5 / 2.6. IS-P 4x19 two halves of loop handle: 2.0 / 1.5. IS-M 5x16 clamp on control handle (loop-handle version): 3.5 / 2.6.
- IS-M 6x20 clamp screw in AV sleeve: 7.0 / 5.2. IS-M 5x20 gearhead clamp screws: 8.0 / 5.9. IS-M 6x25 lower clamp AND upper clamp to handle support: each 6.0 / 4.4.
- IS-M 11x10 screw plug at gearhead grease filler: 10.0 / 7.4. IS-M 6x14 harness clamp: 4.5 / 3.3. IS-M 6x12 clamp on loop handle: 3.5 / 2.6. IS-M 4x12 setscrew in drive-tube sleeve: 3.0 / 2.2.
- ALL OTHER screws/nuts M4: 2.5 / 1.8; M5: 4.5 / 3.3. These are not substitutes for listed component-specific values or the two explicitly unspecified clamp rows. No tool-mounting nut torque is supplied here.
- Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.
Source: TI 37/1994, p. 8 — handle, drive and generic tightening torques.
No additional parts-table entry added.
Wrong number or missing part for the FS 108? Report a correction →