Stihl 4137 · Section A · 1 of 17 · 21 parts
Crankcase, Cylinder
Fits FH 75.
Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.
Parts (21)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 020 2800 | Crankcase, starter side | 1 |
| 2 | 0000 988 8600 | Sleeve | 2 |
| 3 | 9503 003 0242 | Grooved ball bearing 6201 | 2 |
| 4 | 9640 003 1195 | Oil seal 12x22x5 | 2 |
| 5 | 4137 020 2600 | Crankcase, fan side | 1 |
| 6 | 4137 030 0401 | Crankshaft | 1 |
| 7 | 9022 341 1050 | Spline screw IS-M5x25 | 3 |
| 8 | 4137 020 1202 | Cylinder with piston Ø 34 mm Fitment / change note → | 1 |
| 9 | 4137 020 1201 | Cylinder with piston Ø 34 mm Fitment / change note → | 1 |
| 10 | 4137 030 2010 | Piston Ø 34 mm | 1 |
| 11 | 4137 034 3000 | Piston ring Ø 34x1.5 mm | 2 |
| 12 | 4137 034 1500 | Piston pin 8x5x22 | 1 |
| 13 | 9463 650 0805 | Snap ring 8x0.7 | 2 |
| 14 | 9512 003 1830 | Needle cage 8x11x10 | 1 |
| 15 | 4140 029 2300 | Cylinder gasket | 1 |
| 16 | 4137 029 2300 | Cylinder gasket | 1 |
| 17 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 4 |
| 18 | 4137 084 2200 | Guard | 1 |
| 19 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 19 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 20 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 powerhead update: matched cylinder and carburetor
New cylinder 4137 020 1202 requires the three-adjusting-screw carburetor; conflicting printed serials prevent a clean cutoff.
- The revised four transfer ports change port timing and mixture distribution; the TI describes improved volumetric efficiency and combustion, not a measured performance result. The package also standardizes nameplate positions, whose individual later sections remain unreviewed here.
- New cylinder with piston 4137 020 1202 is only for the new three-adjusting-screw carburetor with limiter caps; section 3.2.5 identifies C1Q-S63, 4137 120 0606. The source warns that mixing previous and new cylinder/carburetor versions will cause engine damage. Do not interpret this as banning the documented matched old-generation replacement parts.
- For previous machines, chrome-bore cylinder with piston 4137 020 1201 has been interchangeable with Nikasil-bore 4137 020 1200; only 1201 was to be supplied for previous models after old stocks ran out. This is not the new-generation 1202 cylinder. Included parts remain as before.
- Page 2 gives FS 85 introduction from 2 49 849 196; other cover models are in progress. Page 7 remark 1 instead describes older BIS machines prior to 2 49 848 196. Both are visibly printed, differ by 1000 and remain an unresolved source conflict. No numeric changeover is assigned or corrected by assumption. These are component changeovers, not model production ranges.
- BG 75 and HS 75/80/85 receive only the modifications specifically named in their subsections; they are not included in this new-cylinder/C1Q-S63 pairing.
- Only explicitly named models and configurations are covered. Shared IPL pages do not extend these assertions to unnamed R/RX or other variants. Availability statements describe 2001 factory support, not present stock. The printed cover places FH/HL under 4230, HT under 4138 and KW under 4602; retained exact-model engine sheets use 4137 as navigation, not proof of series equivalence.
Source: TI 16/2001, p. 1 · TI 16/2001, p. 2 · TI 16/2001, p. 3 · TI 16/2001, p. 5 · TI 16/2001, p. 7 — Sections 1–2.2 and 3.2/3.2.5: cylinder generations, model applicability and conflicting serials.
Part numbers (4)
- 4137 020 1200 — Cylinder and piston, Nikasil borePrevious generation · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 020 1201 — Cylinder and piston, chrome boreReplacement for previous generation · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 020 1202 — Cylinder and piston, revised portsNew generation; matched carburetor required · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 120 0606 — Carburetor C1Q-S63Required new-generation pairing · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 shroud replacement: retain the model identity
New shroud moves the company logo and requires a round model nameplate on an older machine.
- The new production shroud changes symbols/access for the three-adjusting-screw carburetor and prints STIHL on its front. The drawing shows H/L/LA access; the service replacement has fewer symbols, illustrated with LA only, so it can serve previous and new versions. The drawing is not a new carburetor adjustment specification.
- Shroud 4137 080 1604 replaces 4137 080 1601, with old stock supplied only while available. When fitting a logo-printed shroud to an old machine, bond the correct new model nameplate to the starter cover; chapter 6 lists twelve exact model assignments.
- The previous round self-adhesive company logo was on the starter cover; new machines print the logo on the shroud. If the old starter-cover logo is unavailable after repair, bond the correct round model nameplate to the starter cover. Neutral label 0000 967 2139 and MADE IN USA label 0000 967 2129 were supplied only while stocks lasted; the summary gives no direct replacement logo number.
- Introduction refers to chapter 1, whose FS 85 update serial 2 49 849 196 differs from the earlier BIS/ignition figure 2 49 848 196. No unified numeric cutoff is assigned.
- Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.
Source: TI 16/2001, p. 10 · TI 16/2001, p. 11 · TI 16/2001, p. 12 — Sections 5–7: shroud, model identity and logo relocation.
Part numbers (4)
- 4137 080 1601 — ShroudPrevious · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 080 1604 — ShroudNew service replacement · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 0000 967 2139 — STIHL nameplate neutralPrevious logo; stocks only · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 0000 967 2129 — STIHL nameplate MADE IN USAPrevious logo; stocks only · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 power tools: exact round nameplate assignments
Twelve models retain distinct old clipped and new self-adhesive nameplate numbers.
- Previous clipped model nameplates fit the old shroud; new round self-adhesive model nameplates are bonded to the starter cover. Previous versions remain spares for older machine versions. A shared engine or IPL sheet does not make model-name labels interchangeable.
- Use the exact model pair below when replacing the shroud or unavailable starter-cover company logo, as required by chapters 5 and 7. Introduction refers to chapter 1; no serial range is inferred.
- Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.
Source: TI 16/2001, p. 10 · TI 16/2001, p. 11 · TI 16/2001, p. 12 — Sections 5.2, 6 and 7.1: complete twelve-row nameplate summary.
Part numbers (24)
- 4137 967 1506 — FC 75 model nameplatePrevious clipped shroud label · FC 75 only; Previous clipped shroud label
- 4137 967 1513 — FC 75 model nameplateNew round starter-cover label · FC 75 only; New round starter-cover label
- 4137 967 1509 — FC 85 model nameplatePrevious clipped shroud label · FC 85 only; Previous clipped shroud label
- 4137 967 1519 — FC 85 model nameplateNew round starter-cover label · FC 85 only; New round starter-cover label
- 4230 967 1503 — FH 75 model nameplatePrevious clipped shroud label · FH 75 only; Previous clipped shroud label
- 4230 967 1508 — FH 75 model nameplateNew round starter-cover label · FH 75 only; New round starter-cover label
- 4137 967 1500 — FS 75 model nameplatePrevious clipped shroud label · FS 75 only; Previous clipped shroud label
- 4137 967 1512 — FS 75 model nameplateNew round starter-cover label · FS 75 only; New round starter-cover label
- 4137 967 1502 — FS 80 model nameplatePrevious clipped shroud label · FS 80 only; Previous clipped shroud label
- 4137 967 1514 — FS 80 model nameplateNew round starter-cover label · FS 80 only; New round starter-cover label
- 4137 967 1501 — FS 85 model nameplatePrevious clipped shroud label · FS 85 only; Previous clipped shroud label
- 4137 967 1515 — FS 85 model nameplateNew round starter-cover label · FS 85 only; New round starter-cover label
- 4137 967 1510 — FS 85 T model nameplatePrevious clipped shroud label · FS 85 T only; Previous clipped shroud label
- 4137 967 1516 — FS 85 T model nameplateNew round starter-cover label · FS 85 T only; New round starter-cover label
- 4230 967 1500 — HL 75 model nameplatePrevious clipped shroud label · HL 75 only; Previous clipped shroud label
- 4230 967 1505 — HL 75 model nameplateNew round starter-cover label · HL 75 only; New round starter-cover label
- 4230 967 1501 — HL 75 K model nameplatePrevious clipped shroud label · HL 75 K only; Previous clipped shroud label
- 4230 967 1506 — HL 75 K model nameplateNew round starter-cover label · HL 75 K only; New round starter-cover label
- 4138 967 1505 — HT 70 model nameplatePrevious clipped shroud label · HT 70 only; Previous clipped shroud label
- 4138 967 1502 — HT 70 model nameplateNew round starter-cover label · HT 70 only; New round starter-cover label
- 4138 967 1500 — HT 75 model nameplatePrevious clipped shroud label · HT 75 only; Previous clipped shroud label
- 4138 967 1503 — HT 75 model nameplateNew round starter-cover label · HT 75 only; New round starter-cover label
- 4602 967 1500 — KW 85 model nameplatePrevious clipped shroud label · KW 85 only; Previous clipped shroud label
- 4602 967 1501 — KW 85 model nameplateNew round starter-cover label · KW 85 only; New round starter-cover label
Service note · FH 75
FH 75: oil-seal grease is not blade-drive lubricant
The 370 g (13 oz) tube of 0781 120 1111 is assigned to oil seals, not to gearbox filling.
- Lube grease 0781 120 1111 is listed in a 370 g (13 oz) tube with application “Oil seals”. The container quantity is not a dose for a seal or a gearbox.
- The TI gives no grease fill quantity, blade-drive lubrication interval or substitution rule. The gear-lubricant listing on later catalog sheets does not change the oil-seal application printed here.
- TI 47/1998 names the FH 75 power scythe, printed series 4230. The retained 01-2012 exact FH 75 sheets are under catalog series 4137: these are model-label navigation links, not proof that the series identifiers or every later configuration are equivalent. No extension to FH attachments, FH-KM or later 135-degree heads, serial cutoff, retrofit or tested physical interchange is established.
Source: TI 47/1998, p. 3 — Page3 section5.2 servicing-aids table, lube-grease row.
Part numbers (1)
- 0781 120 1111 — Lube grease; 370 g (13 oz) tubeServicing aid for oil seals; not gearbox fill quantity · FH 75; TI 47/1998 application only
Service note · FH 75
FH 75: service and repair-time references retain their scope
The TI points to named HL/FS/HS tools, the combined service manual and HL 75 repair times; those references are not a complete FH 75 procedure.
- Section 5.1 says the same special servicing tools are used as for HL 75, FS 75, FS 80, FS 85, HS 75, HS 80 and HS 85. It does not list individual tool numbers or state that every procedure or part from those machines fits the FH 75.
- Section6 says setting and testing data and other information are the same as HL 75 and FS 75/80/85. HS models occur in the tool reference, not this sentence. Companion notes distinguish separately dated 2004 engine/ignition/fuel tables and detailed diagnostic and adjustment variants; the exact original 1998 reference edition remains a bounded source gap.
- Section6.2 refers to the FS 75/80/85,FC 75,HL 75 service manual for FH 75 repairs. Later split editions have verified FH 75 scope; enumerated head, torque, tool, aid, diagnostic and carburetor-adjustment sections are separately admitted. The TI 32/1994 ignition reference is reconciled without erasing differing settings or labels. Original combined and operator editions remain bounded source gaps, not substitutes supplied by those later manuals.
- Section 6.3 says FH 75 repair times are exactly the same as HL 75 in TI 41/1996 and the STIHL repair-times table. The companion FH 75 labor notes now admit the explicit 20-row TI transfer and separately dated 2012 exact-model table, preserving changed codes, units, inclusions, four blanks and the printed zero. The original parent timetable remains a bounded source gap; this is not parts interchange.
- The page 4 imprint identifies 1998 Andreas Stihl AG & Co., Waiblingen, Technical Documentation D1/MTK-sc,6459. It supplies no additional part assignment. No whole manual is imported or reviewed by adding this reference note.
- TI 47/1998 names the FH 75 power scythe, printed series 4230. The retained 01-2012 exact FH 75 sheets are under catalog series 4137: these are model-label navigation links, not proof that the series identifiers or every later configuration are equivalent. No extension to FH attachments, FH-KM or later 135-degree heads, serial cutoff, retrofit or tested physical interchange is established.
Source: TI 47/1998, p. 3 · TI 47/1998, p. 4 — Page 3 sections 5.1 and 6 preamble; page 4 sections 6.2–6.3 and imprint in full.
No additional parts-table entry added.
Wrong number or missing part for the FH 75? Report a correction →