← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section D · 4 of 17 · 39 parts

Air filter, Fuel tank

Fits FH 75.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131314151617181922021222324252627282933031455152535467889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (39)

PosPart numberDescriptionQty
1 4137 129 0905 Gasket 1
2 9007 319 1130 Hexagon head screw M5x62 2
3 4137 121 1601 Spacer flange Fitment / change note → 1
4 9291 021 0121 Washer 5.3 2
5 9022 341 1050 Spline screw IS-M5x25 2
6 4137 182 7600 Tensioner 1
7 4137 123 8900 Pin 1
8 9417 003 7512 Push nut 4.0x9.6x1.8 2
9 9022 313 0680 Spline screw IS-M4x16 1
10 4137 129 0900 Gasket 1
11 4137 120 0614 Carburetor C1Q-S157A 1
11 4137 120 0606 Carburetor C1Q-S63A 1
11 4137 120 0604 Carburetor C1Q-S56A 1
11 4137 120 0603 Carburetor C1Q-S45 1
12 4227 122 1805 Heat shield 1
13 4114 149 1205 Gasket 2
14 4137 140 2801 Filter housing Fitment / change note → 1
15 4137 141 3700 Lever 1
16 4137 141 3801 Choke shutter Fitment / change note → 1
17 9210 261 0700 Hexagon nut M5 2
18 4137 124 2800 Filter 1
19 4137 124 1500 Prefilter 1
20 4137 141 0500 Filter cover 1
21 4137 350 0410 Fuel tank 1
22 0000 989 0516 Grommet 2
23 not sold separately Hose 3.1x5.7x180 mm, R3 not available as a separate item 1
24 not sold separately Hose 3.1x5.7x135 mm, R3 not available as a separate item 1
25 4137 352 8100 Insert 1
26 4137 352 8105 Insert 2
27 0000 350 3502 Pickup body 1
28 4128 350 0505 Filler cap 1
29 0000 350 0900 Rope 1
30 0000 353 0800 Filler cap retainer 1
31 0000 967 3693 Warning pictogram Filler cap 1
51 4137 120 0600 Carburetor C1Q-S28E 1
52 4137 121 1600 Spacer flange Fitment / change note → 1
53 4137 140 2800 Filter housing Fitment / change note → 1
54 4137 141 3800 Choke shutter Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2803 Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85

FH/HL/HT/FC/FS: the 1999 engine upgrade is a matched set

Power rises from 0.9 to 0.95 kW; the filter housing, carburetor and spacer flange cannot be mixed across versions.

1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.

  • The source states an increase from 0.9 kW (1.2 bhp) to 0.95 kW (1.3 bhp), not a measured result from this project. Its exploded drawing labels carburetor 1, filter housing 2, spacer flange 3 and shroud 4; these drawing labels are not catalog positions or quantities.
  • The engine optimization changes the idle system and the four illustrated components. An unchanged engine displacement, top speed, emission rating or fuel ratio is not established by this power statement.
  • The later catalog stores these named machines' common engine assemblies under series 4137. That storage grouping does not revise the original cover's 4230 and 4138 product-series identities. Only exact source model tokens are bound.
  • The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
  • The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
  • For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
  • Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
  • TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.

Source: TI 21/1999, p. 1 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — Section 1 introduction and exploded engine drawing; 1.5.1–1.5.3; 1.5.7; serial and cover/colophon applicability.

No additional parts-table entry added.

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85

FH/HL/HT/FC/FS: filter housing and choke shutter must stay paired

New housing recesses aid felt-filter removal; the wider, smoother choke shutter belongs with the new housing.

1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.

  • The new housing and choke shutter are reshaped for increased air-flow volume. The new housing is identified by recesses (arrows in the right-hand drawing) that allow the felt filter element to be removed without tools. The left-hand drawing is the previous version. No measured flow increase or new filter-element number is supplied.
  • The new choke shutter has a smoother surface and is wider than the previous version. No width dimension is printed. Summary item 1 is a housing including item 2 (the choke shutter); all other parts remain as before. A separate shutter listing does not override the no-mixing rule.
  • The exact-model air-filter catalog sheets retain both pairs. This confirms where the historical evidence belongs; it does not establish current interchange or a replacement of every original housing by the new number.
  • The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
  • The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
  • For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
  • Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
  • TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.

Source: TI 21/1999, p. 1 · TI 21/1999, p. 2 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.1 including continuation on page 2; 1.5.1–1.5.3 and 1.5.7; summary rows 1–2 and remark 1.

Part numbers (4)
  • 4137 140 2800 — Filter housing, originalOriginal; includes original choke shutter · Original configuration; remains a spare under remark 1
  • 4137 140 2801 — Filter housing, newNew; includes new choke shutter · New configuration; summary item 1 includes item 2
  • 4137 141 3800 — Choke shutter, originalOriginal matched component · Only with original filter housing; remains a spare
  • 4137 141 3801 — Choke shutter, newNew matched component · Only with new filter housing

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85

FH/HL/HT/FC/FS: spacer flange 1600 and 1601 are configuration-specific

The original drawing labels 11.8 mm and 12.8 mm flow-section dimensions; these are not carburetor venturi diameters.

1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.

  • The left-hand original spacer flange (1) is annotated 11.8 mm / 0.46 in; the right-hand new flange (2) is annotated 12.8 mm / 0.50 in. The text says the fuel-air-mixture flow cross section is larger. The drawing supplies a linear dimension, not an area, machining allowance or instruction to enlarge the old part.
  • The carburetor paragraph separately says its new venturi is about 1 mm larger. The flange dimensions are not transcribed as the carburetor's absolute bore dimensions. No flow area, volume, gasket thickness or tolerance is inferred.
  • The exact-model catalog air-filter sheets retain both spacer-flange numbers. Historical summary remark 1 keeps the original available as a spare; the new number does not erase the original-machine replacement requirement.
  • The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
  • The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
  • For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
  • Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
  • TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.

Source: TI 21/1999, p. 1 · TI 21/1999, p. 2 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.3 spacer-flange comparison; 1.5.1–1.5.3 and 1.5.7; summary item 21, serial and remark 1.

Part numbers (2)
  • 4137 121 1600 — Spacer flange, originalOriginal version remains available as spare · Original engine configuration; summary item 21, remark 1
  • 4137 121 1601 — Spacer flange, newNew configuration component · New engine configuration; not a standalone universal upgrade

Wrong number or missing part for the FH 75? Report a correction →