← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section O · 14 of 21 · 12 parts

Support frame, Flexible shaft

Fits FR 85 T, FR 85.

Parts diagrams →

Historical fitment & changes (20) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11010111212234566789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (12)

PosPart numberDescriptionQty
1 4128 790 6805 Support frame 1
2 4132 791 1000 Bearing housing 1
3 9503 003 6560 Grooved ball bearing 6202-2Z 1
4 9022 341 1270 Spline screw IS-M6x14 3
5 4128 710 9000 Harness 1
6 4128 718 8000 Buckle 1
7 4203 792 7200 Slide 6
8 4128 710 3000 Flexible shaft 1
9 4128 711 3300 Flexible shaft 1
10 9645 945 7570 O-ring 15.54x2.62 2
11 4133 717 2000 Cap 2
12 4132 182 2100 Retainer 2

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FR 85

FR 85: shared engine and backpack architecture

Source names FS 75/80/85 engine and FR 350/450 frame and shaft; not universal component interchange.

  • The new lightweight semi-professional FR 85 rounds off the lower end of the backpack line. Source states its engine is EXACTLY THE SAME as FS 75, FS 80 and FS 85, and its support frame and shaft are the same as FR 350 and FR 450. Recommended applications are also the same as FR 350/450. These are component-group statements, not a blanket part-number interchange list or permission to transfer all settings between models. No serial boundary is supplied.
  • The product photograph shows the backpack frame, hip support, engine, flexible connection, loop handle and cutting-end guard. It is an overview, NOT a measured routing, connector, clearance or assembly drawing. Ergonomic controls, power-to-weight ratio and reduced fatigue are historical manufacturer descriptions, not measurements.
  • Crankshaft: FIVE parts pressed together as a torsionally rigid assembly. Cylinder: FOUR-port technology for mixture control, combustion and emissions, with larger cooling area. Air filter: improved material, longer claimed life and larger effective surface. These comparative claims specify no dimensions or durability test. Exhaust: dual-chamber muffler.
  • Carburetor has TWO adjusting screws, L and LA. Easy start uses ElastoStart grip AND manual fuel pump. Multi-function handle has soft non-slip grip. Clutch has THREE shoes WITHOUT linings. Drive system combines a FLEXIBLE shaft and drive tube with RIGID shaft running in a protective liner.
  • Newly developed THREE-POINT spring AV system and comfortable backpack system use an integral HIP BELT to carry load at the hip and relieve shoulders/spine. This does not establish compatibility of later AV components. Contents lists sections 1–7; it is a navigation list, not additional service instructions.
  • Historical FR 85, series 4137, as described in TI34/1998. Shared FR 85 T catalog sheets do not extend this note to FR 85 T or other variants. No hardware operation was performed; no physical interchange test or current stock claim.

Source: TI 34/1998, p. 1 · TI 34/1998, p. 2 — Complete introduction and product photograph; contents and every technical-description item.

No additional parts-table entry added.

Service note · FR 85

FR 85: cutting-head and metal-tool noise and vibration

Printed equivalent levels retain tool type, standard, operating condition and right/left handle ordering.

  • CUTTING HEAD: equivalent sound pressure Lpeq 95 dB(A), sound power Lweq 110 dB(A); idle vibration RIGHT 0.7 / LEFT 0.4 m/s²; MAX. RPM vibration RIGHT 2.3 / LEFT 2.7 m/s².
  • METAL TOOL: equivalent sound pressure Lpeq 89 dB(A), sound power Lweq 103 dB(A); idle vibration RIGHT 0.7 / LEFT 0.4 m/s²; MAX. RPM vibration RIGHT 3.0 / LEFT 2.3 m/s². Do not transpose handles or tool rows.
  • Sound pressure standard ISO 7917; sound power ISO 10884; vibration ISO 7916. Footnote 1 on the sound columns: weighted equivalent level includes IDLING AND RACING with the SAME duration of exposure. This is not a current occupational exposure assessment or a vibration daily-dose calculation. The table does not name a particular approved head/blade or give uncertainty values.
  • Historical FR 85, series 4137, as described in TI34/1998. Shared FR 85 T catalog sheets do not extend this note to FR 85 T or other variants. No hardware operation was performed; no physical interchange test or current stock claim.

Source: TI 34/1998, p. 3 — Complete two-row acoustic/vibration table, headers, units and footnote.

No additional parts-table entry added.

Historical fitment · FR 85

FR 85: starter, guard, sharpening aid and separate lubricants

Drive/flexible-shaft grease differs from gearbox grease; transport guard covers four specified metal tools.

  • Transport guard 4119 790 3906 is listed for cutting blades 230-2, 230-4, 230-8 AND brush knife 250-3. It is not a running deflector. Later catalog V sheet has guard 4116 790 3901, diameter 350; no supersession/equivalence to the 1998 number is established by this TI. Preserve both sources independently.
  • ElastoStart 0000 190 3400 is the rewind-starter GRIP WITH ROPE; separate ElastoStart rope is printed 0000 195 8200. The retained starter sheet contains the exact grip and separate later rope options. Do not silently substitute a later rope length/diameter or resolve the earlier TI41/1997 rope-number conflict from this later listing.
  • STIHL gear lubricant for DRIVE SHAFT AND FLEXIBLE SHAFT: 80 g / 3 oz tube 0781 120 1109; 225 g / 8 oz tube 0781 120 1110. STIHL gear lubricant for GEARBOX: 80 g / 3 oz tube 0781 120 1117; 225 g / 8 oz tube 0781 120 1118. Identical generic lubricant labels do NOT make these two application groups interchangeable; no dosage or interval is supplied.
  • STIHL special oil 0781 417 1315, 100 ml / 3.5 fl.oz bottle: rewind spring AND BEARING BORE IN ROPE ROTOR. Sharpening template 4020 890 5500 is listed for BRUSH KNIFE; no blade angle, sharpening limit or circular-saw setting tool is specified here.
  • Historical FR 85, series 4137, as described in TI34/1998. Shared FR 85 T catalog sheets do not extend this note to FR 85 T or other variants. No hardware operation was performed; no physical interchange test or current stock claim.

Source: TI 34/1998, p. 4 — Section 4 accessory table and section 4.2 sharpening aid, every row and application.

Part numbers (9)
  • 4119 790 3906 — Transport guard for four named metal cutting toolsTransport accessory · FR 85; exact historical application only
  • 0000 190 3400 — ElastoStart grip with ropeStarter accessory · FR 85; exact historical application only
  • 0000 195 8200 — ElastoStart ropeSeparate historical starter rope · FR 85; exact historical application only
  • 0781 120 1109 — Shaft lubricant, 80 gDrive shaft and flexible shaft only · FR 85; exact historical application only
  • 0781 120 1110 — Shaft lubricant, 225 gDrive shaft and flexible shaft only · FR 85; exact historical application only
  • 0781 120 1117 — Gearbox lubricant, 80 gGearbox application · FR 85; exact historical application only
  • 0781 120 1118 — Gearbox lubricant, 225 gGearbox application · FR 85; exact historical application only
  • 0781 417 1315 — STIHL special oil, 100 mlRewind spring and rope-rotor bearing bore · FR 85; exact historical application only
  • 4020 890 5500 — Sharpening templateBrush knife · FR 85; exact historical application only

Service note · FR 85

FR 85: separate powerhead and backpack repair references

Source gaps remain for Standard Repairs / Troubleshooting, the exact FR85 owner manual and 1998 editions; reviewed later references do not resolve retained conflicts.

  • For SPECIAL SERVICING TOOLS, TIGHTENING TORQUES and SERVICING/REPAIR PROCEDURES, TI34/1998 explicitly refers to FS 75, FS 80 and FS 85 manuals for the POWERHEAD, and FR 350 and FR 450 manuals for SHAFT AND SUPPORT FRAME. Do not transfer FR 350/450 engine settings to the FR 85 powerhead. No manual edition or numeric torque is specified here.
  • Additional special-tool information is delegated to TI36/1996 (FS 75/80/85). That reference is not a new blanket tooling or complete-machine interchange assertion. Previously reviewed TI36 tool notes and their retained tool-number conflict are unchanged. Available later powerhead, common-components, FR-specific, FS/FR and CombiTools procedures have now been dispositioned within their printed model and edition boundaries; they do not establish the exact manuals intended in 1998.
  • Section 6.3 says the referenced manuals do NOT include Servicing the Carburetor, Troubleshooting or repairs involving STANDARD PROCEDURES. It delegates those to the separate handbooks Carburetors and Standard Repairs, Troubleshooting. This is the 1998 source description, not a claim that every later manual omits those chapters. The available Carburetors handbook (copyright 1999; revision unestablished) has been reviewed as a later comparison. The separately named STANDARD REPAIRS, TROUBLESHOOTING handbook was NOT LOCATED in the bounded local source inventory; its contents remain a source gap, not inferred from another manual.
  • If a unit is STARTED during repair or maintenance, the source requires strict observance of all LOCAL AND NATIONAL safety regulations and the OWNER’S MANUAL safety precautions. The exact FR85 OWNER’S MANUAL was NOT LOCATED in the bounded local source inventory; those delegated precautions remain a source gap. The STIHL service catalogue User Guide is catalog-software help, NOT the machine owner’s manual. A cutting-attachment catalog and a later KombiTools manual do not replace it. No jurisdiction-specific regulation set is supplied by the TI or inferred here. No start-up or under-load run was performed.
  • Section 7 states that an illustrated parts list is AVAILABLE FOR THE NEW MODEL. This is a historical availability statement only: no IPL order number, edition, publication authorization or current availability is supplied. The retained later FR 85 catalog is a separate reference. Copyright 1998 and Technical Documentation footer identify the source; they add no interchange assertion.
  • SOURCE-INVENTORY LIMIT: the retained service documentation and owner service-manual PDFs, catalog document index and available text sidecars were reconciled; this is not a whole-world absence claim. Exact 1998 powerhead/shaft/frame and handbook editions remain unestablished. Later torque-label, fixture-number, lubricant/application, sealant, sealing-plate, vacuum, ignition and gearbox input/output-wording conflicts remain unchanged. Review complete WITH DOCUMENTED SOURCE GAPS does not mean complete repair instructions or verified physical interchange.
  • Historical FR 85, series 4137, only. Shared FR 85 T catalog sheets do not extend these assertions to FR 85 T or other variants. No hardware operation was performed; no physical interchange or current stock claim.

Source: TI 34/1998, p. 5 · TI 34/1998, p. 6 — Sections 5.1, 6 safety paragraph, 6.2, 6.3 and 7 complete.

No additional parts-table entry added.

Service note · FR 85

FR 85: all 29 historical repair-time rows

Minutes assume trained personnel and an equipped workshop; eight dashes are not zero-minute jobs.

  • The printed times are MINUTES and assume TRAINED PERSONNEL in a PROPERLY EQUIPPED SERVICE WORKSHOP. The source says this FR 85 table can be added to the STIHL repair-times table. These are historical workshop allowances, not measured task durations, a current quotation, repair instructions or evidence of a hardware test.
  • ASTERISK means TEST RUN UNDER LOAD and applies to rows 2, 3, 4, 6, 7 and 10 only. Rows explicitly saying test run without an asterisk are not silently given that extra footnote. Printed row 7 wording is Ignition system, contact; no contact-point ignition is inferred from that wording.
  • Rows 1–8: 1. Remove and refit engine — 20 min; 2. Crankcase, pressure test* — 110 min; 3. Crankshaft, bearings, pressure test* — 110 min; 4. Sealing rings, pressure test* — 70 min; 5. Crankcase leakage test, test run — 40 min; 6. Cylinder, piston, pressure test* — 55 min; 7. Ignition system, contact* — 10 min; 8. Fuel supply, tank vent, test run — 10 min.
  • Rows 9–16: 9. Manifold or flange, pressure test — DASH (no time supplied); 10. Carburetor, check* — 30 min; 11. Handle and throttle control — 10 min; 12. Rewind starter, test run — 15 min; 13. Clutch, test run — 20 min; 14. Muffler — 10 min; 15. Air filter — 5 min; 16. Stop switch, test run — 10 min.
  • Rows 17–22: 17. Clutch housing — 20 min; 18. Drive tube — 25 min; 19. Replace gearhead or bearing housing — 5 min; 20. Limit stop or deflector — 10 min; 21. Drive shaft — 15 min; 22. Fuel tank — 20 min.
  • Rows 23–29: 23. Check compression pressure — DASH (no time supplied); 24. Adjust valve clearance — DASH (no time supplied); 25. Replace crankcase, bottom half — DASH (no time supplied); 26. Replace crankshaft — DASH (no time supplied); 27. Replace cylinder, piston — DASH (no time supplied); 28. Oil supply — DASH (no time supplied); 29. Oil pump, test run — DASH (no time supplied).
  • DASH rows 9 and 23–29 supply NO TIME, not zero minutes and not confirmation that the named operation applies to FR 85. In particular, valve clearance, oil supply and oil pump row labels do not establish four-stroke valves or a chain-oiling system on this machine. Do not equate standalone dash rows 26/27 with the timed combined pressure-test jobs 3/6.
  • Historical FR 85, series 4137, only. Shared FR 85 T catalog sheets do not extend these assertions to FR 85 T or other variants. No hardware operation was performed; no physical interchange or current stock claim.

Source: TI 34/1998, p. 6 — Section 6.4 entire 29-row repair-times table, assumptions, add-to-table note and under-load footnote.

No additional parts-table entry added.

Service note · FR 85

FR 85: later backpack shaft lubrication and removal reference

FR 350/450 instructions preserve thin grease application, blue-shaft replacement and model-specific clamp values.

  • Later-manual comparison following TI34/1998 sections 5.1, 6.2 and 6.3, not proof of the exact manuals available in 1998. The TI delegates POWERHEAD work to FS 75/80/85 literature and SHAFT/SUPPORT FRAME work to FR 350/450 literature. Later values and tooling require a matching component/configuration; they are not blanket FR 85 or FR 85 T repair settings.
  • Later FR 350/450 section 10.5, PDF pages 54–55 / printed pages 53–54: take the throttle cable out of its TWO retainers; press the lever at the clutch housing and withdraw the flexible-shaft assembly; release the lever at the other housing and withdraw it there; pull the flexible shaft from its drive tube. The drawings distinguish the two release locations.
  • If the flexible shaft has TURNED BLUE, the source says FIT A NEW ONE. Before installation coat the WHOLE shaft UNIFORMLY AND THINLY with STIHL gear lubricant 0781 120 1109; DO NOT PUMP GREASE DIRECTLY INTO THE DRIVE TUBE. Inspect the O-ring and replace if needed; reinstall the flexible shaft and route the throttle cable in its retainers. No grease mass, service interval or diagnosis solely from absence of bluing is supplied.
  • Do not transfer adjacent section 10.4’s rigid-shaft protrusion dimensions to this flexible shaft: PDF page 54 assigns dimension A = 20 mm / 0.8 inch to FS 120/200 and 30 mm / 1.2 inch to FS 300…450, NOT FR 350/450 or FR 85.
  • FR 350/450 drive-tube section 10.6, PDF page 56, calls for drive-shaft and housing removal, releasing the two control-handle clamps, then withdrawing handle and sleeve; reverse for assembly, align the control handle per section 7.4 and tighten clamp screws to 2.0 Nm / 1.5 lbf.ft. Section 10.7, PDF page 57, instead gives the HOUSING/SHAFT clamp 4.5 Nm / 3.3 lbf.ft after degreasing its mounting area; torque table PDF page 7 identifies IS-M6x25 with FR350/450 remarks 2 and 5. These are DIFFERENT JOINTS, not conflicting values.
  • Internal housing service is explicitly delegated to Standard Repairs, Troubleshooting; this note does not supply that missing procedure. The FR control-handle alignment and drive-shaft removal cross-references remain a bounded follow-up, not invented steps. The adjacent FS drive-tube clamp torques and gearhead operations are not admitted as FR 85 values.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — Sections 5.1, 6.2 and 6.3: delegated literature; bounded later-manual comparison.

Later manual evidence: FS 120, 200, 300, 350, 400, 450; FR 350, 450 (2003-04), section Section 10.5 complete, FR-only portions of 10.6–10.7 and table cross-check; adjacent FS exclusion, PDF pages 1, 7, 54, 55, 56, 57

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later backpack support-frame bearing reference

The later FR 350/450 frame procedure separates its two fastening torques and the bearing press tool from clutch work.

  • Later-manual comparison following TI34/1998 sections 5.1, 6.2 and 6.3, not proof of the exact manuals available in 1998. The TI delegates POWERHEAD work to FS 75/80/85 literature and SHAFT/SUPPORT FRAME work to FR 350/450 literature. Later values and tooling require a matching component/configuration; they are not blanket FR 85 or FR 85 T repair settings.
  • FR 350/450 section 12.1, PDF page 59 / printed page 58: first remove the powerhead from the support frame per section 9.3; remove the support-frame screw; lever the frame out of the ball bearing; remove the bearing-housing screws and lift out the housing. Powerhead removal and spring/AV details are a separate prerequisite, not supplied in full by this paragraph.
  • Use press arbor 1118 893 7200 to REMOVE the ball bearing from its housing and to press the bearing HOME AS FAR AS STOP on assembly. Reassemble in reverse sequence. The tool table, PDF page 61 row 41, explicitly lists removal/installation of the bearing in the support-frame bearing housing for FR 350/450. It also lists a different clutch-housing operation, which is not the same joint.
  • Section 12.1 specifies bearing-housing mounting screws 10.0 Nm / 7.5 lbf.ft and support-frame mounting screw 20.0 Nm / 15 lbf.ft. Table PDF page 7 binds these respectively to IS-M6x14 — Bearing housing/support frame, and IS-M10x20 — Support plate/ball bearing/support frame; remarks 2 and 5 identify FR450 and FR350. Preserve the printed units and values; no 1998 FR85 fastener match or physical torque verification is inferred.
  • The LEFT column of PDF page 59 is the CONTINUATION OF CLUTCH-DRUM section 11.2, not frame section 12.1. Its 8.5 Nm clutch-housing value, FS120/200 6.0 Nm exception and clutch-drum drift instructions are NOT support-frame torque instructions. Column/section boundaries matter even when the same press arbor appears in both.
  • This closes the bounded later frame-bearing section comparison, not all FR 85 service dependencies. Section 9.3 removal/refitting, exact original-edition applicability and the owner-safety/standard-repair handbooks still require separate disposition.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — Sections 5.1, 6.2 and 6.3: delegated literature; bounded later-manual comparison.

Later manual evidence: FS 120, 200, 300, 350, 400, 450; FR 350, 450 (2003-04), section Section 12.1 complete, frame-specific torque-table rows and tool row 41; excludes adjacent clutch-drum column, PDF pages 1, 7, 59, 61

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later backpack powerhead and AV-spring removal reference

The FR 350/450 prerequisite uses three springs and new locknuts; adjacent rubber-buffer instructions are not its procedure.

  • Later-manual comparison following TI34/1998 sections 5.1, 6.2 and 6.3, not proof of the exact manuals available in 1998. The TI delegates POWERHEAD work to FS 75/80/85 literature and SHAFT/SUPPORT FRAME work to FR 350/450 literature. Later values and tooling require a matching component/configuration; they are not blanket FR 85 or FR 85 T repair settings.
  • FS/FR manual 2003-04, section 9.3, PDF page 51 / printed page 50, explicitly describes THREE SPRINGS between the FR 350/450 engine and support frame. First remove the flexible shaft from the clutch housing per section 10.5; that release and lubrication reference is separately retained in the flexible-shaft note.
  • Remove the spline screws (figure callout 1) and hexagon-head screw (2) from the clutch housing, then take the powerhead off the support plate. To remove the springs from the plate, HOLD THE SCREWS STEADY while unscrewing the nuts (1), then remove the springs (2). The two figures reuse callouts for different objects; do not treat every callout 1 as the same fastener.
  • Reassemble in reverse sequence. Use NEW LOCKNUTS and tighten to 10 Nm / 7.5 lbf.ft. Tighten the spline screws AND hexagon-head screw to 10 Nm / 7.5 lbf.ft. The torque table, PDF page 7 / printed page 6, separately lists IS-M6x14 — Spring/support plate — 10.0 Nm / 7.5 lbf.ft with FR450/FR350 remarks 2 and 5; it does not establish the thread of every screw in the preceding removal figure.
  • The LEFT column on PDF page 51 finishes the PRECEDING rubber-buffer AV procedure, including its gap adjustment. It is NOT section 9.3 FR 350/450 spring guidance. No rubber-buffer gap, spring part number, spring replacement interval or FR85 fastener/thread equivalence is invented. This is the delegated FRAME prerequisite, not admission of FR350/450 internal engine repair for FR85.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — Sections 5.1, 6.2 and 6.3: delegated literature; bounded later-manual comparison.

Later manual evidence: FS 120, 200, 300, 350, 400, 450; FR 350, 450 (2003-04), section Section 9.3 complete and spring/support-plate torque-table row; excludes preceding AV column, PDF pages 7, 51

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later backpack control-handle alignment and spring seating

Keep the 20 mm control-handle gap separate from the 20 cm loop-handle spacing and distinguish clamp from molding screws.

  • Later-manual comparison following TI34/1998 sections 5.1, 6.2 and 6.3, not proof of the exact manuals available in 1998. The TI delegates POWERHEAD work to FS 75/80/85 literature and SHAFT/SUPPORT FRAME work to FR 350/450 literature. Later values and tooling require a matching component/configuration; they are not blanket FR 85 or FR 85 T repair settings.
  • Section 7.4, PDF page 36 right column through page 37 left column / printed pages 35–36: after removal of the interlock lever under section 7.3, pull the slide control off the handle molding, remove the clamp screws, take the molding off the drive tube and remove the torsion spring from its peg. Reassemble in reverse sequence; clamp screws 2 Nm / 1.5 lbf.ft.
  • The groove (1) in the slide control must engage OVER THE OUTER EDGE (2) of the handle molding; the torsion spring (3) must engage the recess (4) in the slide control. These seating requirements are part of the reassembly reference, not optional picture details.
  • For FR 350/450 specifically, dimension a BETWEEN CONTROL HANDLE AND HOUSING is 20 mm / 0.8 inch (PDF page 37, drawing 250RA237). This is the alignment referenced by the FR drive-tube section 10.6 on PDF page 56. It is NOT the loop-handle dimension A = 20 cm / 8 inches measured from the control handle in adjacent section 10.3 on PDF page 53. The latter applies to both illustrated loop-handle arrangements, with and without barrier bar; it is not a tenfold correction to the 20 mm gap.
  • Section 7.3 prerequisite, PDF page 35 right column and page 36 left/middle columns: for FR350/450 use screwdriver 5910 890 2301 to remove the guard screw and push the guard forward. The source explicitly warns DO NOT START THE UNIT WHILE THE CONTROL HANDLE IS OPEN, to avoid electric shock. Remove molding screws with that screwdriver, remove the molding and torsion spring, then lift the trigger with its cable off the peg and disconnect the cable. Lift the contact spring slightly to free the cable; lift the interlock lever with contact spring off the peg and separate that spring.
  • On reverse assembly under section 7.3, check the positions of throttle cable (1), contact spring (2), protective tube (3) and insulator (4). Its molding screws are 1.0 Nm / 0.75 lbf.ft, NOT the 2 Nm clamp screws in section 7.4. The torque table PDF page 7 calls the molding joint IS-P4x16. Adjacent bike-handle contact/detent-spring section 7.2 and the section 7.5 throttle-cable/powerhead branches are not silently combined with this loop-handle procedure.
  • Section 10.3 disassembly distinguishes arrangements: without barrier bar, remove nuts/lower clamp, then screws/loop handle/upper clamp; with barrier bar, remove screws/lower clamp, barrier bar/loop handle/upper clamp and square nuts from the bar. Both reassemble in reverse, align the loop handle at the printed 20 cm / 8 inch distance and tighten firmly. That paragraph supplies NO numeric loop-handle torque. The table’s 4.5 Nm Clamp/loop handle row is explicitly marked FS120/200 (remark 3), not proof of an FR85 loop-handle torque.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — Sections 5.1, 6.2 and 6.3: delegated literature; bounded later-manual comparison.

Later manual evidence: FS 120, 200, 300, 350, 400, 450; FR 350, 450 (2003-04), section Sections 7.3–7.4 complete; section 10.3 complete; FR-only 10.6 alignment pointer and torque-row boundary, PDF pages 7, 35, 36, 37, 53, 56

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later rigid shaft, liner and gearhead prerequisite reference

The rigid shaft in the working tube is not the backpack flexible shaft; FR protrusion dimensions remain unspecified.

  • Later-manual comparison following TI34/1998 sections 5.1, 6.2 and 6.3, not proof of the exact manuals available in 1998. The TI delegates POWERHEAD work to FS 75/80/85 literature and SHAFT/SUPPORT FRAME work to FR 350/450 literature. Later values and tooling require a matching component/configuration; they are not blanket FR 85 or FR 85 T repair settings.
  • FR350/450 drive-tube section 10.6 on PDF page 56 explicitly delegates DRIVE SHAFT removal to section 10.4, while section 10.5 separately covers the flexible backpack shaft. Section 10.4, PDF pages 53–54 / printed pages 52–53, describes a drive shaft supported in a flexible liner inside a tube whose ends have plugs. The liner is not the flexible drive shaft itself.
  • Section 10.4: remove the gearhead per section 11.1, then pull the drive shaft from the tube. If the shaft has TURNED BLUE, FIT A NEW ONE. Before installation coat the WHOLE drive shaft UNIFORMLY AND THINLY with STIHL gear lubricant 0781 120 1109; DO NOT PUMP GREASE DIRECTLY INTO THE DRIVE TUBE. Push the shaft into the tube.
  • The continuation specifies protrusion A = 20 mm / 0.8 inch for FS120/200 and 30 mm / 1.2 inch for FS300…450, with slight pressure and slow rotation if needed, then gearhead refitting. It supplies NO FR350/450 or FR85 protrusion dimension. Do not copy either FS value or the unrelated 20 mm control-handle gap as an FR drive-shaft insertion setting.
  • For flexible-liner removal, section 10.4 calls for drive-tube removal under section 10.6, prying out the plug and pulling out the liner; insert the plug and reinstall the tube afterward. Its hole-between-spokes orientation note explicitly names FS120/200 ONLY. No FR-specific liner orientation, part equivalence or insertion dimension is established.
  • Section 11.1, PDF page 57 / printed page 56: remove the deflector or stop if fitted, release clamps and pull the gearhead off the tube. The drawing is explicitly FS120/200. Refitting text calls for degreasing the clamp mounting area, sliding the gearhead onto the tube while turning the output shaft back and forth to engage the square shaft end in the pinion socket, pushing home as far as stop and aligning, then refitting the deflector or stop. Clamp screws are 8.5 Nm / 6.3 lbf.ft for FS120/200 AND FR350/450; the FS300…450 two-stage 1.5 then 7.5 Nm procedure is NOT the FR branch.
  • The same section’s retainer/thrust-washer removal is labeled FS300…450, followed by guard-ring removal, the separate Standard Repairs and Troubleshooting handbook pointer for further internal disassembly/assembly, FS300…450 guard-ring torque 5.0 Nm and a new-retainer instruction. Those are not admitted as universal FR85 gearhead internals. The adjacent FR housing clamp is 4.5 Nm, not the 8.5 Nm gearhead clamp. Internal handbook procedures remain a separate actionable dependency; no complete gearhead overhaul is claimed.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — Sections 5.1, 6.2 and 6.3: delegated literature; bounded later-manual comparison.

Later manual evidence: FS 120, 200, 300, 350, 400, 450; FR 350, 450 (2003-04), section Section 10.4 complete and explicit FR 10.6 pointer; section 11.1 removal/refitting with model boundaries; internal overhaul remains delegated, PDF pages 53, 54, 56, 57

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: FR-specific three-spring AV reference

Three engine-to-frame springs and new locknuts are explicit; later FR fastener rows differ from FR350/450.

  • Later FR-specific Components 4137 reference, edition 2005-05, following TI34/1998 sections 5.1, 6.2 and 6.3. This is RA_265, distinct from the previously compared FC–KW manual RA_394 (2004-06) and FR350/450 manual RA_250 (2003-04). Exact 1998 FR85 configuration remains unestablished. Match the actual component and fasteners; these are not blanket FR85 or FR85T repair settings.
  • Section7.1 describes THREE SPRINGS between the ENGINE AND SUPPORT FRAME. Remove the flexible shaft from the clutch housing; remove the fan-housing screws shown in936RA387 and lift the ENGINE WITH TANK from the fan housing. This is not the rigid-drive-tube rubber element described in the FC–KW comparison.
  • HOLD THE SCREWS STEADY while unscrewing the nuts and remove the springs from the engine mounting plate (936RA424). Reassemble in reverse sequence and use NEW LOCKNUTS. The drawing identifies the nuts and springs; it does not supply a spring part number, measured stiffness, service interval or interchange boundary.
  • The FR-specific3.2 table lists nut IS-M6 — FAN HOUSING/SPRING/SCREW —8.0 Nm (5.9 lbf.ft), and screw IS-M6x37 — SPRING/FAN HOUSING, REAR —8.0 Nm (5.9 lbf.ft). Section7.1 itself supplies no numeric torque. Keep these exact table labels; do not assume every unlabelled fastener in the drawing has the same thread.
  • The previously retained FR350/450 section9.3 gives10 Nm (7.5 lbf.ft) for its locknuts and spline/hexagon-head screws. The FR-specific8 Nm rows must not silently overwrite that different model/configuration source or become a blanket correction to all1998 FR85 machines. No physical joint match has been verified.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections5.1,6.2,6.3: later FR-specific component comparison.

Later manual evidence: Components 4137 — FR, HLR, HTR (2005-05), section 7.1 complete;3.2 spring/fan-housing rows, PDF pages 6, 24 · FS 120, 200, 300, 350, 400, 450; FR 350, 450 (2003-04), section Section 9.3 complete and spring/support-plate torque-table row; excludes preceding AV column, PDF pages 7, 51

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: flexible-shaft guidance retains a lubricant-label conflict

The FR-specific procedure confirms blue-shaft replacement and no direct grease pumping, but its servicing-aids labels disagree.

  • Later FR-specific Components 4137 reference, edition 2005-05, following TI34/1998 sections 5.1, 6.2 and 6.3. This is RA_265, distinct from the previously compared FC–KW manual RA_394 (2004-06) and FR350/450 manual RA_250 (2003-04). Exact 1998 FR85 configuration remains unestablished. Match the actual component and fasteners; these are not blanket FR85 or FR85T repair settings.
  • Section10.4 removes the throttle cable from TWO retainers, presses the release lever at the clutch housing to disconnect that end, then the lever at the other housing to disconnect the other end. Pull the flexible shaft out. If it has TURNED BLUE, ALWAYS INSTALL A NEW ONE. These steps corroborate the separately retained FR350/450 reference; no blue-free shaft is thereby certified undamaged.
  • Before installation coat the shaft with STIHL GEAR LUBRICANT FOR HEDGE TRIMMERS, referring to12, and apply it EVENLY. NEVER PUMP LUBRICANT DIRECTLY INTO THE FLEXIBLE DRIVE TUBE. Inspect the O-ring and replace if necessary, reinstall the shaft and reattach the throttle cable to its retainers. The FR-specific passage supplies no grease mass or interval; the earlier FR350/450 reference separately says uniformly and thinly.
  • Section12 item4 names that hedge-trimmer gear lubricant as 0781 120 1109, but labels its application HIGH VOLTAGE OUTPUT ON IGNITION MODULE. Item2 instead lists STIHL shaft grease 0781 120 6602 (40 g tube) for DRIVE SHAFT IN FLEXIBLE LINER. Preserve the visible procedure/table application discrepancy and the distinct flexible-shaft versus rigid-shaft-in-liner contexts; do not silently change the procedure to6602, apply gear grease to an ignition output, or claim the products equivalent.
  • TI34/1998 section4 already assigns 0781 120 1109 to drive/flexible shafts and distinguishes gearbox lubricants. That historical application and the FR350/450 procedure remain independently retained evidence; they do not erase the FR-specific table inconsistency or authorize substitution.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections5.1,6.2,6.3: later FR-specific component comparison.

Later manual evidence: Components 4137 — FR, HLR, HTR (2005-05), section 10.4 complete;12 items2,4, PDF pages 49, 52 · FS 120, 200, 300, 350, 400, 450; FR 350, 450 (2003-04), section Section 10.5 complete, FR-only portions of 10.6–10.7 and table cross-check; adjacent FS exclusion, PDF pages 1, 7, 54, 55, 56, 57

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: flexible-shaft bearing-housing internals

The later FR-specific procedure identifies the release-lever stack, shaft circlips and square-end assembly orientation.

  • Later FR-specific Components 4137 reference, edition 2005-05, following TI34/1998 sections 5.1, 6.2 and 6.3. This is RA_265, distinct from the previously compared FC–KW manual RA_394 (2004-06) and FR350/450 manual RA_250 (2003-04). Exact 1998 FR85 configuration remains unestablished. Match the actual component and fasteners; these are not blanket FR85 or FR85T repair settings.
  • Press down the housing lever, disconnect the flexible shaft, loosen clamp screw(1) and pull housing(2) off drive tube(3) (936RA338/339). This is the FLEXIBLE-SHAFT CONNECTION housing, not the support-frame pivot bearing or clutch drum. The earlier delegated Standard Repairs pointer is supplemented by this later explicit FR procedure, not evidence that the exact1998 handbook has been found.
  • Ease E-clip(1) off lever(2), remove washer(3), and pull out the lever WITH torsion spring(4) (936RA340). Remove the protective cap IF FITTED. Then remove the HOUSING circlip (936RA342). The E-clip, housing circlip and subsequent shaft circlip are three separately located retainers, not interchangeable callouts.
  • Use drift 1108 893 4700 to PRESS THE SHAFT OUT OF THE HOUSING (936RA343); section11 item10 independently lists it for removing the shaft. Remove the circlip FROM THE SHAFT, then pull the BALL BEARING off the shaft (936RA344/345). No bearing order number, press force, fit tolerance or substitute drift is supplied.
  • Assemble in reverse sequence. Insert the shaft SQUARE END FIRST into the housing and push it home until it BUTTS AGAINST THE BALL BEARING (936RA346). Push the housing onto the drive tube and ensure the HOLES ALIGN (936RA347). Keep this orientation distinct from the flexible-shaft cable end and support-frame pivot. No dimensional seating depth or extra lubricant application is invented.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections5.1,6.2,6.3: later FR-specific component comparison.

Later manual evidence: Components 4137 — FR, HLR, HTR (2005-05), section 10.4.1 complete;11 item10, PDF pages 49, 50, 51

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later frame and housing fasteners are configuration-specific

The FR-specific torque table must not be blended with the earlier FR350/450 comparison or split-boom rows.

  • Later FR-specific Components 4137 reference, edition 2005-05, following TI34/1998 sections 5.1, 6.2 and 6.3. This is RA_265, distinct from the previously compared FC–KW manual RA_394 (2004-06) and FR350/450 manual RA_250 (2003-04). Exact 1998 FR85 configuration remains unestablished. Match the actual component and fasteners; these are not blanket FR85 or FR85T repair settings.
  • FR-specific3.2 lists IS-M10x40 — ENGINE MOUNTING/BALL BEARING/SUPPORT FRAME —9.5 Nm (7.0 lbf.ft); IS-M6x14 — BEARING HOUSING/SUPPORT FRAME —8.0 Nm (5.9 lbf.ft); and IS-M6x25 — HOUSING/DRIVE TUBE CLAMP SCREW —8.0 Nm (5.9 lbf.ft). The first two are frame joints; the last is the housing/drive-tube clamp context. Equal torque does not make them one joint.
  • The prior FR350/450 table lists IS-M10x20 support-plate/frame at20 Nm and bearing-housing/support-frame IS-M6x14 at10 Nm; its housing/shaft clamp is4.5 Nm. Preserve those model-specific values and different M10 screw length. Neither common naming nor the TI shared-architecture statement proves identical fasteners or authorizes replacing an earlier value with a later one.
  • The M6x30 coupling-sleeve wing screw6 Nm and IS-M6x25 coupling-sleeve/hex-nut9 Nm rows carry remark1, FR85T ONLY. Do not apply these split-boom values to unsuffixed FR85. The loop-handle/barrier-bar/drive-tube IS-M6x25 row is9 Nm and visibly carries remarks1,2,3; their labels are FR85T only, FR85 only and HLR85 only respectively. Retain all three printed references, not a fabricated single-model restriction or universal handle torque.
  • For reusing a DG or P screw, rotate COUNTERCLOCKWISE until it drops into the existing thread, then tighten clockwise to the specified torque; use a torque wrench. Polymer power-screwdriver maxima are600 rpm for Plastoform and500 rpm for DG. Do not mix screws WITH and WITHOUT binding heads. These installation-speed maxima are not engine speeds, and thread-forming screw instructions do not establish the size of an unidentified mounting screw.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections5.1,6.2,6.3: later FR-specific component comparison.

Later manual evidence: Components 4137 — FR, HLR, HTR (2005-05), section 3.2 mounting/clamp rows and screw-reuse instructions;10.4.1 joint context, PDF pages 6, 7, 49, 50 · FS 120, 200, 300, 350, 400, 450; FR 350, 450 (2003-04), section Section 12.1 complete, frame-specific torque-table rows and tool row 41; excludes adjacent clutch-drum column, PDF pages 1, 7, 59, 61

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later FR-specific rigid-shaft protrusion is 17 mm

A later FR-specific manual supplies a shaft-end dimension missing from the earlier FR350/450 comparison.

  • Later FR-specific Components 4137 reference, edition 2005-05, following TI34/1998 sections 5.1, 6.2 and 6.3. This is RA_265, distinct from the previously compared FC–KW manual RA_394 (2004-06) and FR350/450 manual RA_250 (2003-04). Exact 1998 FR85 configuration remains unestablished. Match the actual component and fasteners; these are not blanket FR85 or FR85T repair settings.
  • Section10.2 is explicitly NOT FR85T. The RIGID DRIVE SHAFT inside the working tube is separate from the backpack flexible shaft in10.4. Remove the gearbox using the CombiTools manual and remove the bearing housing under10.4.1 before withdrawing the shaft. Section10.3 also removes the loop handle and the throttle-cable retainer WHERE FITTED; reverse the sequence for assembly. It does not establish a new clamp torque.
  • The FR-specific2005-05 section10.2 drawing936RA265 sets dimension a to17 mm, measured from the TUBE END TO THE PROJECTING SHAFT END. Apply slight pressure and rotate the shaft slowly if necessary until that dimension is obtained. This is an insertion/protrusion reference, not a shaft wear limit or tube length.
  • The earlier FR350/4502003-04 section10.4 supplied20 mm for FS120/200 and30 mm for FS300–450 but no FR dimension. That earlier-source gap remains true of that source; the later17 mm statement supplies a separate FR-specific reference, not proof of the exact1998 FR85 configuration. Neither FS value nor the20 mm control-handle gap is an alternative FR shaft setting.
  • If the shaft has TURNED BLUE, ALWAYS INSTALL A NEW ONE. Coat the shaft uniformly with STIHL gear lubricant 0781 120 1109 before insertion; NEVER PUMP LUBRICANT DIRECTLY INTO THE DRIVE TUBE. No grease mass, shaft part number or service interval is stated.
  • The explicit 0781 120 1109 rigid-shaft procedure also conflicts with section12 item2 assigning shaft grease 0781 120 6602 to DRIVE SHAFT IN FLEXIBLE LINER; item4 labels 0781 120 1109 for HIGH VOLTAGE OUTPUT ON IGNITION MODULE. Preserve all original application labels; do not silently substitute products or treat the ignition application label as corrected procedure. Earlier flexible-shaft lubricant conflicts remain unchanged.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections5.1,6.2,6.3: later FR-specific component comparison.

Later manual evidence: Components 4137 — FR, HLR, HTR (2005-05), section 10.2 drive-shaft branch;10.3;12 lubricant-label comparison, PDF pages 46, 48, 52 · FS 120, 200, 300, 350, 400, 450; FR 350, 450 (2003-04), section Section 10.4 complete and explicit FR 10.6 pointer; section 11.1 removal/refitting with model boundaries; internal overhaul remains delegated, PDF pages 53, 54, 56, 57

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later FR-specific liner hole lies between the spokes

The FR-specific liner procedure supplies an orientation and plug-extraction tool, without borrowing split-boom construction.

  • Later FR-specific Components 4137 reference, edition 2005-05, following TI34/1998 sections 5.1, 6.2 and 6.3. This is RA_265, distinct from the previously compared FC–KW manual RA_394 (2004-06) and FR350/450 manual RA_250 (2003-04). Exact 1998 FR85 configuration remains unestablished. Match the actual component and fasteners; these are not blanket FR85 or FR85T repair settings.
  • The10.2 heading explicitly excludes FR85T. The drive shaft is supported in a FLEXIBLE LINER whose ENDS ARE SEALED WITH PLUGS. After removing the shaft, use hook 5910 890 2800 to pull out the plug (936RA172), then pull out the liner (936RA207). No heating, cutting or press load is specified for this branch.
  • On refitting, HOLE(1) MUST BE BETWEEN SPOKES(2), as drawn in936RA208. Fit the plug and then the drive shaft, with the separate17 mm shaft-end dimension in10.2. The earlier FR350/450 manual limited its hole-between-spokes statement to FS120/200; the later FR-specific manual independently supplies this orientation. It does not establish interchangeable liners or a historical serial boundary.
  • The10.3 removal prerequisite is gearbox, bearing housing, loop handle and drive shaft removal, followed by the throttle-cable retainer WHERE FITTED. Section10.1 corroborates the already recorded barrier-bar clamp stack and ABOUT20 cm loop-handle position FORWARD OF THE CONTROL HANDLE. Keep that spacing separate from the20 mm control-handle/housing gap and17 mm shaft projection. The paragraph says tighten firmly, not a numeric loop-handle torque.
  • Adjacent10.2.1 and10.3.1 are FR85T ONLY: coupling sleeve, lock button, retaining clips and heat-assisted sleeve removal are separate split-boom construction. Visually reviewed for exclusion; none is imported as an FR85 instruction. Page48 left-column continuation of10.2.1 must not be merged into its middle-column10.3 non-split procedure.
  • Gearbox removal remains delegated to the CombiTools manual. Local RA_227_00_01_02.pdf explicitly names FR85 on its2007-02 cover; section3 assigns FR85 to the FS gearbox row, type AG (ANGLE GEAR). This is a later construction assignment, not a common part number or proof of exact1998 fitment. Applicable gearbox internals still require original-page review. The2016-02 FS Gearboxes document mislabeled015 is not a substitute for establishing the1998 gearbox identity.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections5.1,6.2,6.3: later FR-specific component comparison.

Later manual evidence: Components 4137 — FR, HLR, HTR (2005-05), section 10.2 liner branch;10.1 and10.3 prerequisites;10.2.1/10.3.1 scope exclusion, PDF pages 45, 46, 47, 48 · FS 120, 200, 300, 350, 400, 450; FR 350, 450 (2003-04), section Section 10.4 complete and explicit FR 10.6 pointer; section 11.1 removal/refitting with model boundaries; internal overhaul remains delegated, PDF pages 53, 54, 56, 57 · CombiTools (2007-02), section Cover identity and section3 FR85 FS/AG assignment only; internal procedures pending, PDF pages 1, 5

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later gearbox fitting guidance has a torque-table boundary

Square-drive engagement and clamp preparation are specified; model-specific torque rows must not be silently transferred.

  • Later CombiTools reference, edition 2007-02 (RA_227), following TI34/1998 sections 5.1, 6.2 and 6.3 and the FR-specific gearbox-removal dependency. Cover and section 3 explicitly bind FR 85 to FS angle gearbox (AG); section 4.3 footnote 2 explicitly includes FR 85 under FS 4137. This is later construction evidence, not proof of the exact 1998 gearbox, a shared part number or universal FR85T applicability.
  • Section 7.1.1 removes cutting tools and deflector AS NECESSARY, loosens the screws and withdraws the gearbox. For installation, DEGREASE THE CLAMP MOUNTING AREA; turn the output shaft back and forth while sliding the gearbox on so the square drive-shaft end engages the square socket in the drive pinion. Push fully to the stop and align the gearbox before tightening.
  • The instruction says tighten firmly and refers to 4.1. Its table has NO EXPLICIT FR85 REMARK. Footnote 7 means FS80/85, not FR85: the 9.5 Nm IS-M11x10 screw-plug row and 4.3 Nm IS-M5x16 deflector row must remain FS-labeled comparisons. The same-sized IS-M11x10 plug has a separate 10.0 Nm row for FC75/FS55. Do not infer an FR85 clamp or plug torque from the common FS/AG assignment.
  • Likewise the 9.0 Nm IS-M6x20 gearbox/drive-tube row is FC75; 10.0 Nm is FH75/HL45; 8.0 Nm IS-M6x30 is FC85; 12.0 Nm DG6x28 is FS55. Exact FR85 fastening specification remains unestablished in this table, not supplied by selecting a convenient neighboring row.
  • The FC/FCB-only wheel and deflector steps, FCS fixing-screw/hole alignment and KW sleeves on the same page are not FR85 instructions. Earlier FR350/450 removal/refitting evidence remains independent; no earlier torque or tool conflict is overwritten.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections 5.1, 6.2, 6.3: later CombiTools FS gearbox dependency.

Later manual evidence: CombiTools (2007-02), section 7.1.1; 4.1 complete table and footnotes, PDF pages 1, 5, 6, 7, 17

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later FS gearbox dismantling uses ordered heat-assisted removal

The input and output retaining rings and removal order are explicit; the pinion and bevel gear form a matching set.

  • Later CombiTools reference, edition 2007-02 (RA_227), following TI34/1998 sections 5.1, 6.2 and 6.3 and the FR-specific gearbox-removal dependency. Cover and section 3 explicitly bind FR 85 to FS angle gearbox (AG); section 4.3 footnote 2 explicitly includes FR 85 under FS 4137. This is later construction evidence, not proof of the exact 1998 gearbox, a shared part number or universal FR85T applicability.
  • Remove the gearbox under 7.1.1. Section 7.2 removes the CIRCLIP AT THE INPUT END and the CIRCLIP IN THE OUTPUT-END GROOVE before heating the gearbox housing to ABOUT 110–140 °C. Remove the INPUT components FIRST, THEN OUTPUT components by knocking the housing against a WOODEN BASE. This is a housing-temperature instruction, not a bearing or running-temperature limit.
  • Pull the ball bearing and bevel gear from the drive shaft (227RA063); remove the drive-pinion circlip (227RA064), then press the drive pinion out of its ball bearings (227RA065). Clean all parts and inspect for serviceability. No clearance limit, press-force specification or permitted damaged-part reuse is supplied.
  • The drive pinion and bevel gear are available ONLY AS A MATCHING PINION SET. No set part number, universal interchange or historical serial boundary is established here. FC/FCB deflector and wheel prerequisites are expressly branch-specific, not added to FR85.
  • Section 10 lists press arbor 4119 893 7200 for removing/installing ball bearings. Its oil-seal puller and needle-sleeve drift serve other listed applications; 7.2 does not instruct adding an oil-seal or needle-sleeve operation to this gearbox.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections 5.1, 6.2, 6.3: later CombiTools FS gearbox dependency.

Later manual evidence: CombiTools (2007-02), section 7.2 dismantling; 7.1.1 prerequisite; 10 tools, PDF pages 1, 5, 17, 19, 73

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later gearbox bearings retain their open and closed orientation

Bearing heating, matched-gear assembly and retaining-ring placement are source-bound, with a shaft-label discrepancy preserved.

  • Later CombiTools reference, edition 2007-02 (RA_227), following TI34/1998 sections 5.1, 6.2 and 6.3 and the FR-specific gearbox-removal dependency. Cover and section 3 explicitly bind FR 85 to FS angle gearbox (AG); section 4.3 footnote 2 explicitly includes FR 85 under FS 4137. This is later construction evidence, not proof of the exact 1998 gearbox, a shared part number or universal FR85T applicability.
  • Heat the drive-pinion ball bearings to ABOUT 50 °C before fitting. The OPEN bearing must be against the PINION; the CLOSED bearing is at the end with the CIRCLIP GROOVE. Refit that circlip. The adjacent FS55 exception has only one ball bearing and is not an FR85 instruction.
  • On printed page 19 the first two captions say INPUT SHAFT: heat its ball bearing to ABOUT 50 °C and fit to the stop, then fit the bevel gear TEETH FIRST. Yet 227RA068/069 depict the threaded shaft previously called drive shaft in 227RA063 and subsequently called OUTPUT SHAFT in 227RA071. Preserve this INPUT/OUTPUT WORDING DISCREPANCY; do not silently relabel the original or confuse this assembly with the drive pinion.
  • Heat the gearbox housing to ABOUT 140 °C for installation; press the ball bearing fully home, then press the preassembled OUTPUT SHAFT home. Push the preassembled DRIVE PINION home and CHECK THE PINION AND BEVEL-GEAR TEETH MESH PROPERLY. Fit the circlips at both input and output housing ends. No numerical backlash or bearing-preload setting is provided.
  • The separate 110–140 °C dismantling range and 50 °C bearing preparation must not be collapsed into one temperature. The later instructions do not establish the exact 1998 bearing revision or justify using unmatched gears.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections 5.1, 6.2, 6.3: later CombiTools FS gearbox dependency.

Later manual evidence: CombiTools (2007-02), section 7.2 assembly, including 227RA067–075, PDF pages 1, 5, 19, 20

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · FR 85

FR 85: later FS 4137 gearbox uses 9 g initial fill and conditional top-up

The 9 g initial fill is distinct from the maximum 5 g re-lubrication amount and the visible-grease condition.

  • Later CombiTools reference, edition 2007-02 (RA_227), following TI34/1998 sections 5.1, 6.2 and 6.3 and the FR-specific gearbox-removal dependency. Cover and section 3 explicitly bind FR 85 to FS angle gearbox (AG); section 4.3 footnote 2 explicitly includes FR 85 under FS 4137. This is later construction evidence, not proof of the exact 1998 gearbox, a shared part number or universal FR85T applicability.
  • Section 4.3 explicitly lists FR85 in footnote 2 of the FS4137 gearbox row: TYPE A lubricant, 9 g INITIAL FILL, MAXIMUM 5 g RE-LUBRICATION. Type A means STIHL GEAR LUBRICANT FOR BRUSHCUTTERS. Do not substitute the FS4140/FS55 initial fill of 15 g or add 5 g automatically to a newly filled gearbox.
  • Section 7.2 removes the screw plug, screws the grease tube into the opening and fills according to 4.3. During maintenance, TOP UP ONLY IF NO GREASE IS VISIBLE ON THE INSIDE OF THE SCREW PLUG. The 5 g figure is a maximum top-up, not an unconditional dose or a service interval.
  • Section 11 item 7 identifies brushcutter gear lubricant 0781 120 1117 (80 g tube) and 0781 120 1118 (225 g tube), application gearbox/drive shaft. Item 6 separately labels 0781 120 1109 (80 g) and 0781 120 1110 (225 g) as HEDGE-TRIMMER gear lubricant. Preserve these exact product/application distinctions.
  • The earlier FR-specific shaft procedure uses 0781 120 1109, while its aid table has conflicting ignition-output and flexible-liner application labels. Those earlier shaft conflicts remain unchanged: this CombiTools brushcutter GEARBOX reference neither resolves them nor authorizes replacing every shaft lubricant with the gearbox product.
  • No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.

TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections 5.1, 6.2, 6.3: later CombiTools FS gearbox dependency.

Later manual evidence: CombiTools (2007-02), section 4.3 FS4137 row and footnote 2; 7.2 lubrication; 11 items 6–7, PDF pages 1, 5, 8, 20, 74

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Wrong number or missing part for the FR 85 T, FR 85? Report a correction →