Stihl 4137 · Section N · 13 of 25 · 31 parts
Drive tube assembly FS 75, Loop handle
Fits FS 75.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (31)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 710 7113 | Drive tube assembly Ø 25.4 mm / 1'' | 1 |
| 2 | 4137 710 7112 | Drive tube assembly Ø 25.4 mm / 1'' Fitment / change note → | 1 |
| 3 | 0000 967 3726 NLA | Warning pictogram FS | 1 |
| 4 | 0000 967 3659 NLA | Warning pictogram FS | 1 |
| 5 | 4130 711 3210 | Drive shaft Fitment / change note → | 1 |
| 6 | 4133 717 2000 | Cap | 1 |
| 7 | 9455 621 1130 | Circlip 12x1 | 1 |
| 8 | 9099 021 2360 | Self-tapping screw 3.5x9.5 | 1 |
| 9 | 4130 640 1405 | Bearing housing | 1 |
| 10 | 9513 003 3210 | Needle cage 12x16x10 | 2 |
| 11 | 4130 640 2205 | Drive shaft | 1 |
| 12 | 0000 958 1233 | Washer | 2 |
| 13 | 4130 713 1501 | Thrust plate | 1 |
| 14 | 4130 710 6701 | Hose clamp | 1 |
| 15 | 9022 341 1010 | Spline screw IS-M5x18 | 1 |
| 16 | 9210 260 0700 | Hexagon nut M5 | 1 |
| 17 | 4130 713 4501 | Deflector | 1 |
| 18 | 4130 713 4100 | Blade | 1 |
| 19 | 9074 478 4405 | Pan head self-tapping screw IS-P6x14 | 1 |
| 20 | 9771 021 2760 | Hose clip Ø 1 7/8x1/2" | 1 |
| 22 | 4130 790 1200 | Loop handle | 1 |
| 23 | 4130 791 2000 | Handle hose | 1 |
| 24 | 9075 478 4115 | Pan head self-tapping screw IS-D5x16 | 1 |
| 25 | 4130 791 6805 | Clamp | 1 |
| 26 | 9041 116 1430 | Pan head screw M6x50 | 1 |
| 27 | 9222 068 0900 | Square nut M6 | 1 |
| 28 | 9022 341 1430 | Spline screw IS-M6x50 | 1 |
| 29 | 9294 021 0140 | Washer 6.4 | 1 |
| 30 | 0000 711 2500 | Sleeve | 1 |
| 40 | 4133 710 7100 | Drive tube assembly Ø 25.4 mm / 1'' Fitment / change note → | 1 |
| 41 | 4130 711 3200 | Drive shaft Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 75 / FS 80 / FS 80 R / FS 85 / FS 85 R
FS 75 / 80 / 85: shaft construction, thread direction and gear ratio
FS 75 has M12 right-hand mounting; FS 80/85 use M10 × 1 left-hand. FS 80/85 gear ratio changes from 1:1.33 to 1:1.4 without a printed cutoff.
- FS 75 and FS 80 have FLEXIBLE drive shafts; FS 85 has a RIGID shaft. All are supported in a protective tube. Do not assume that a straight drive tube proves a rigid shaft or apply the later shared-sheet FS 85 T/RX entries to this introduction.
- Figure 392TI003: FS 75 output shaft (4), described as on FS 72, has M12 RIGHT-HAND thread; no pitch is printed. FS 80/85 output shaft (3), described as on FS 74/76/86/88/106/108, has M10 × 1 LEFT-HAND thread. The named mounting similarity is not permission to fit every cutting tool used on those models.
- FS 80/85 gearhead ratio is 1:1.33 at start of production, later 1:1.4. No serial, date or gearhead/pinion order number maps these two ratios. The later X and Y IPL gearheads are not silently assigned to either ratio.
- Rated maximum OUTPUT SHAFT speed: FS 75 8,500 rpm; FS 80/85 7,500 rpm, explicitly WITH 1:1.4 gear ratio. Do not transfer the 7,500 value to the initial 1:1.33 gearhead or confuse output-shaft speed with engine cut-off speed.
- Scope is the 1996 series 4137 introduction, including depicted R and RB handle arrangements. No scope is inherited by FS 85 T/RX, FC/FR/HL/HT/KM/KW/SP models or later same-named machines from a shared IPL sheet. Historical source guidance, not current stock or verified physical interchange. No hardware operation was performed.
Source: TI 36/1996, p. 3 · TI 36/1996, p. 4 — FS 75 / 80 / 85: shaft construction, thread direction and gear ratio.
No additional parts-table entry added.
Service note · FS 75
FS 75: 102 mm longer shaft requires the complete matched assembly
From X 36 865 750; do not mix the old and new tube, liner and drive shaft.
X 36 865 750 — FS75 longer complete shaft introduction only; not FS72 or short replacement drilling.
- FS75 receives a102 mm (4 in.) longer shaft to improve handling FROM MACHINE NUMBER X 36 865 750. This cutoff is FS75 ONLY, not FS72 or other models sharing the current sheet. FS72 introduction of standardized spare supply is merely in progress.
- Original and new DRIVE TUBE(1), FLEXIBLE LINER(2) and FLEXIBLE DRIVE SHAFT(3) are ONLY INTERCHANGEABLE AS COMPLETE ASSEMBLIES. Drawing392TI011 KN identifies all three nested components. Do not interpret the table as permission to combine a long tube with a short shaft/liner or to extend only one component.
- FS75 drive tube4137 710 7110→4137 710 7112 and shaft4130 711 3200→4130 711 3210. Original tube supplied only until existing factory stocks exhausted (remark1). Flexible liner has -*- in both columns and is NOT AVAILABLE AS A SEPARATE ITEM (remark3); no liner number invented. Original shaft remains a spare (remark4), because short FS75 and FS72 continue to use3200.
- Current exact FS75 sheet retains7112/3210 and also short4133 710 7100/3200. Its additional7113 tube is not silently substituted or claimed equivalent. Shared FS80/85 and R/T/RX headings do not extend this FS75-only change. The short replacement drilling conditions are a separate note on the same source.
- Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.
Source: TI 35/1997, p. 1 · TI 35/1997, p. 2 — Page1 length change, drawing items1–3; page2 long-shaft rows, liner, supply and introductions.
Part numbers (4)
- 4137 710 7110 — Original short drive tubeFactory stock exhaustion · Only the exact model/configuration and restrictions of 1997-35
- 4137 710 7112 — New longer drive tubeFS75 long assembly · Only the exact model/configuration and restrictions of 1997-35
- 4130 711 3200 — Original short drive shaftRemains spare for short FS75 and FS72 · Only the exact model/configuration and restrictions of 1997-35
- 4130 711 3210 — New longer drive shaftFS75 long assembly · Only the exact model/configuration and restrictions of 1997-35
Service note · FS 72 / FS 75
FS 72 / short FS 75: shared replacement tube needs the correct fixing hole
4133 710 7100 is pre-drilled for FS72; short FS75 needs its separate 6 mm hole.
- To standardize spares, FS72 tube4133 710 7100 is supplied also for SHORT-SHAFT FS75, replacing4137 710 7110 in that short configuration. FS72 keeps4133 710 7100. Both new supply rows carry remark2: WITH DRILLING TEMPLATE. Original FS75 tube stock exhaustion is remark1. The shared short shaft4130 711 3200 stays unchanged and available as a spare (remark4). This is not the longer7112/3210 assembly.
- The source says the only tube difference between FS72 and FS75 in this SHORT-SHAFT replacement context is fixing-screw hole position. Replacement7100 is PRE-DRILLED FOR FS72. Drill the separate FS75 hole using template4; PEEL THE TEMPLATE OFF BEFORE fitting the shaft in the AV sleeve. Figure392TI012 KN shows the template aligned with the existing hole; its printed label is0000 967 3722 A SAL. The printed identifier is not evidence of separate factory supply.
- Without a template, page2 drawing392TI013 KN locates hole centers from the SAME RIGHT-HAND TUBE END: FS75 at66.3 mm (printed66,3; 2 5/8 in.), FS72 at54 mm (2 1/8 in.). The FS75 hole diameter is6 mm (1/4 in.). These are center-to-end distances, not center spacing, tube length or drilling depth. The new FS75 center lies farther from the end than the existing FS72 center; do not reverse the labels. Printed metric and inch values are retained, not treated as exact mathematical conversions.
- Flexible liner is unnumbered and not separately available. No cutting, bore depth, through-both-walls direction, alternative hole angle or screw torque is specified; no extra instruction invented. This source is sufficient for the recorded template/no-template distinction, not a complete machine disassembly manual. FS72 supply change is IN PROGRESS; X36 865 750 belongs to longer FS75 production, not a drilling cutoff.
- Bind only exact FS72 and FS75 drive-tube sheets. Other FS74/76/80/85 shared-sheet models do not inherit this drilling permission. Footer references TI12.95 and TI36.96 are prior-model bibliography, not missing procedural dependencies. All page1 diagrams, page2 dimensions, six table rows and four supply remarks reviewed.
- Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.
Source: TI 35/1997, p. 1 · TI 35/1997, p. 2 — Page1 short-shaft replacement/template and removal; page2 dimensional drawing and full summary.
Part numbers (4)
- 4137 710 7110 — Original short FS75 drive tubeFactory stock exhaustion · Only the exact model/configuration and restrictions of 1997-35
- 4133 710 7100 — FS72 / short FS75 replacement tubeSupplied with drilling template · Only the exact model/configuration and restrictions of 1997-35
- 4130 711 3200 — Shared short drive shaftUnchanged; remains spare · Only the exact model/configuration and restrictions of 1997-35
- 0000 967 3722 — Drilling-template printed identifierFigure label; separate orderability not established · Only the exact model/configuration and restrictions of 1997-35
Wrong number or missing part for the FS 75? Report a correction →