Stihl 4137 · Section A · 1 of 24 · 21 parts
Crankcase, Cylinder
Fits HT 70, HT 75.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (21)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 020 2800 | Crankcase, starter side | 1 |
| 2 | 0000 988 8600 | Sleeve | 2 |
| 3 | 9503 003 0242 | Grooved ball bearing 6201 | 2 |
| 4 | 9640 003 1195 | Oil seal 12x22x5 | 2 |
| 5 | 4137 020 2600 | Crankcase, fan side | 1 |
| 6 | 4137 030 0401 | Crankshaft | 1 |
| 7 | 9022 341 1050 | Spline screw IS-M5x25 | 3 |
| 8 | 4137 020 1202 | Cylinder with piston Ø 34 mm Fitment / change note → | 1 |
| 9 | 4137 020 1201 | Cylinder with piston Ø 34 mm Fitment / change note → | 1 |
| 10 | 4137 030 2010 | Piston Ø 34 mm | 1 |
| 11 | 4137 034 3000 | Piston ring Ø 34x1.5 mm | 2 |
| 12 | 4137 034 1500 | Piston pin 8x5x22 | 1 |
| 13 | 9463 650 0805 | Snap ring 8x0.7 | 2 |
| 14 | 9512 003 1830 | Needle cage 8x11x10 | 1 |
| 15 | 4140 029 2300 | Cylinder gasket | 1 |
| 16 | 4137 029 2300 | Cylinder gasket | 1 |
| 17 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 4 |
| 18 | 4137 084 2200 | Guard | 1 |
| 19 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 19 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 20 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 powerhead update: matched cylinder and carburetor
New cylinder 4137 020 1202 requires the three-adjusting-screw carburetor; conflicting printed serials prevent a clean cutoff.
- The revised four transfer ports change port timing and mixture distribution; the TI describes improved volumetric efficiency and combustion, not a measured performance result. The package also standardizes nameplate positions, whose individual later sections remain unreviewed here.
- New cylinder with piston 4137 020 1202 is only for the new three-adjusting-screw carburetor with limiter caps; section 3.2.5 identifies C1Q-S63, 4137 120 0606. The source warns that mixing previous and new cylinder/carburetor versions will cause engine damage. Do not interpret this as banning the documented matched old-generation replacement parts.
- For previous machines, chrome-bore cylinder with piston 4137 020 1201 has been interchangeable with Nikasil-bore 4137 020 1200; only 1201 was to be supplied for previous models after old stocks ran out. This is not the new-generation 1202 cylinder. Included parts remain as before.
- Page 2 gives FS 85 introduction from 2 49 849 196; other cover models are in progress. Page 7 remark 1 instead describes older BIS machines prior to 2 49 848 196. Both are visibly printed, differ by 1000 and remain an unresolved source conflict. No numeric changeover is assigned or corrected by assumption. These are component changeovers, not model production ranges.
- BG 75 and HS 75/80/85 receive only the modifications specifically named in their subsections; they are not included in this new-cylinder/C1Q-S63 pairing.
- Only explicitly named models and configurations are covered. Shared IPL pages do not extend these assertions to unnamed R/RX or other variants. Availability statements describe 2001 factory support, not present stock. The printed cover places FH/HL under 4230, HT under 4138 and KW under 4602; retained exact-model engine sheets use 4137 as navigation, not proof of series equivalence.
Source: TI 16/2001, p. 1 · TI 16/2001, p. 2 · TI 16/2001, p. 3 · TI 16/2001, p. 5 · TI 16/2001, p. 7 — Sections 1–2.2 and 3.2/3.2.5: cylinder generations, model applicability and conflicting serials.
Part numbers (4)
- 4137 020 1200 — Cylinder and piston, Nikasil borePrevious generation · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 020 1201 — Cylinder and piston, chrome boreReplacement for previous generation · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 020 1202 — Cylinder and piston, revised portsNew generation; matched carburetor required · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 120 0606 — Carburetor C1Q-S63Required new-generation pairing · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 shroud replacement: retain the model identity
New shroud moves the company logo and requires a round model nameplate on an older machine.
- The new production shroud changes symbols/access for the three-adjusting-screw carburetor and prints STIHL on its front. The drawing shows H/L/LA access; the service replacement has fewer symbols, illustrated with LA only, so it can serve previous and new versions. The drawing is not a new carburetor adjustment specification.
- Shroud 4137 080 1604 replaces 4137 080 1601, with old stock supplied only while available. When fitting a logo-printed shroud to an old machine, bond the correct new model nameplate to the starter cover; chapter 6 lists twelve exact model assignments.
- The previous round self-adhesive company logo was on the starter cover; new machines print the logo on the shroud. If the old starter-cover logo is unavailable after repair, bond the correct round model nameplate to the starter cover. Neutral label 0000 967 2139 and MADE IN USA label 0000 967 2129 were supplied only while stocks lasted; the summary gives no direct replacement logo number.
- Introduction refers to chapter 1, whose FS 85 update serial 2 49 849 196 differs from the earlier BIS/ignition figure 2 49 848 196. No unified numeric cutoff is assigned.
- Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.
Source: TI 16/2001, p. 10 · TI 16/2001, p. 11 · TI 16/2001, p. 12 — Sections 5–7: shroud, model identity and logo relocation.
Part numbers (4)
- 4137 080 1601 — ShroudPrevious · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 080 1604 — ShroudNew service replacement · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 0000 967 2139 — STIHL nameplate neutralPrevious logo; stocks only · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 0000 967 2129 — STIHL nameplate MADE IN USAPrevious logo; stocks only · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 power tools: exact round nameplate assignments
Twelve models retain distinct old clipped and new self-adhesive nameplate numbers.
- Previous clipped model nameplates fit the old shroud; new round self-adhesive model nameplates are bonded to the starter cover. Previous versions remain spares for older machine versions. A shared engine or IPL sheet does not make model-name labels interchangeable.
- Use the exact model pair below when replacing the shroud or unavailable starter-cover company logo, as required by chapters 5 and 7. Introduction refers to chapter 1; no serial range is inferred.
- Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.
Source: TI 16/2001, p. 10 · TI 16/2001, p. 11 · TI 16/2001, p. 12 — Sections 5.2, 6 and 7.1: complete twelve-row nameplate summary.
Part numbers (24)
- 4137 967 1506 — FC 75 model nameplatePrevious clipped shroud label · FC 75 only; Previous clipped shroud label
- 4137 967 1513 — FC 75 model nameplateNew round starter-cover label · FC 75 only; New round starter-cover label
- 4137 967 1509 — FC 85 model nameplatePrevious clipped shroud label · FC 85 only; Previous clipped shroud label
- 4137 967 1519 — FC 85 model nameplateNew round starter-cover label · FC 85 only; New round starter-cover label
- 4230 967 1503 — FH 75 model nameplatePrevious clipped shroud label · FH 75 only; Previous clipped shroud label
- 4230 967 1508 — FH 75 model nameplateNew round starter-cover label · FH 75 only; New round starter-cover label
- 4137 967 1500 — FS 75 model nameplatePrevious clipped shroud label · FS 75 only; Previous clipped shroud label
- 4137 967 1512 — FS 75 model nameplateNew round starter-cover label · FS 75 only; New round starter-cover label
- 4137 967 1502 — FS 80 model nameplatePrevious clipped shroud label · FS 80 only; Previous clipped shroud label
- 4137 967 1514 — FS 80 model nameplateNew round starter-cover label · FS 80 only; New round starter-cover label
- 4137 967 1501 — FS 85 model nameplatePrevious clipped shroud label · FS 85 only; Previous clipped shroud label
- 4137 967 1515 — FS 85 model nameplateNew round starter-cover label · FS 85 only; New round starter-cover label
- 4137 967 1510 — FS 85 T model nameplatePrevious clipped shroud label · FS 85 T only; Previous clipped shroud label
- 4137 967 1516 — FS 85 T model nameplateNew round starter-cover label · FS 85 T only; New round starter-cover label
- 4230 967 1500 — HL 75 model nameplatePrevious clipped shroud label · HL 75 only; Previous clipped shroud label
- 4230 967 1505 — HL 75 model nameplateNew round starter-cover label · HL 75 only; New round starter-cover label
- 4230 967 1501 — HL 75 K model nameplatePrevious clipped shroud label · HL 75 K only; Previous clipped shroud label
- 4230 967 1506 — HL 75 K model nameplateNew round starter-cover label · HL 75 K only; New round starter-cover label
- 4138 967 1505 — HT 70 model nameplatePrevious clipped shroud label · HT 70 only; Previous clipped shroud label
- 4138 967 1502 — HT 70 model nameplateNew round starter-cover label · HT 70 only; New round starter-cover label
- 4138 967 1500 — HT 75 model nameplatePrevious clipped shroud label · HT 75 only; Previous clipped shroud label
- 4138 967 1503 — HT 75 model nameplateNew round starter-cover label · HT 75 only; New round starter-cover label
- 4602 967 1500 — KW 85 model nameplatePrevious clipped shroud label · KW 85 only; Previous clipped shroud label
- 4602 967 1501 — KW 85 model nameplateNew round starter-cover label · KW 85 only; New round starter-cover label
Service note · HT 70
HT 70: carburetor kit and separate lubricant applications
Kit 4227 007 1060 is listed for Zama C1Q-S28C / C1Q-S41; oil-seal, gearbox and drive-shaft greases have separate order numbers and tube sizes.
- Carburetor parts kit 4227 007 1060 is assigned to Zama C1Q-S28C and C1Q-S41 as printed. Do NOT silently change those suffixes to the later catalog sheet C1Q-S28E / C1Q-S41C. The shared sheet is only navigation; kit contents and applicability to later suffixes are not established here.
- Lube grease 0781 120 1111, 225 g / 8 oz TUBE: OIL SEALS. Lube grease 0781 120 6602, 40 g / 1.4 oz TUBE: GEAR BOX. Lube grease 0781 120 1109, 80 g / 2.8 oz TUBE: DRIVE SHAFT. These are package sizes, NOT quantities to install.
- The three printed application labels are retained independently. Do not swap grease applications, infer equivalence with other editions or treat tube mass as a gearbox fill. No maintenance interval, fill amount or replacement product is specified by this table. Existing lubricant/application conflicts in other notes remain unchanged.
- Historical HT 70 only. TI35/1998 calls this series 4138; the retained exact-model IPL is filed under 4137. That navigation association does not establish series equivalence, extend these assertions to HT 75 or later variants, or prove physical interchange. No production serial or current stock claim is supplied. No hardware operation was performed.
Source: TI 35/1998, p. 3 — Section 5.2 complete table; section 5.1 reference retained separately.
Part numbers (4)
- 4227 007 1060 — Carburetor parts kitHistorical servicing kit · HT 70; TI35/1998 Zama C1Q-S28C and C1Q-S41 only as printed
- 0781 120 1111 — Lube grease, 225 g / 8 oz tubeOil-seal servicing aid · HT 70; TI35/1998 oil seals; package size, not installed quantity
- 0781 120 6602 — Lube grease, 40 g / 1.4 oz tubeGearbox servicing aid · HT 70; TI35/1998 gear box; package size, not fill amount
- 0781 120 1109 — Lube grease, 80 g / 2.8 oz tubeDrive-shaft servicing aid · HT 70; TI35/1998 drive shaft; package size, not installed quantity
Service note · HT 70
HT 70: repair references and historical parts-list issue
Available HT70 repair dependencies reviewed; exact historical handbooks, owner precautions and the 3.98 IPL remain documented source gaps.
- Section 5.1 says the same special servicing tools are used as for FS 85 brushcutters. Section 6.1 says setting/testing data and other information are the same as HT 75 and FS 85 brushcutters (SHAFT). This supplies no numeric setting, torque or tool order number; it does not make the HT70 a brushcutter.
- The named service manual is FS 75, 80, 85, FC 75, HL 75; missing GEARHEAD procedures are delegated to TI03/1997. Applicable retained TI procedures and later explicitly HT70-bound Components (2005-04), Powerhead (2004-03) and CombiTools (2007-02) sections have been reviewed separately. Exact historical FS manual and E14/E20 tensioner-manual editions remain bounded source gaps. Later sources do not prove original 1998 configuration; HT75-only revisions are not silently rebound to HT70.
- The cited historical manual omits Servicing the Carburetor, Troubleshooting and standard procedures, delegating them to separate CARBURETOR and STANDARD REPAIRS, TROUBLESHOOTING handbooks. Neither requested handbook is established in the retained PDF inventory, reviewed manual headers and reference-document index. The available Chain and Bar, Special Tools, 019 T, 020 T and HS/BG service manuals are different works. Their references to handbooks are not the handbooks themselves. This is a bounded source gap, not universal absence; later HT70-specific carburetor/troubleshooting content remains separately reviewed evidence.
- If the unit is STARTED during repair or maintenance, section 6 requires all LOCAL SAFETY REGULATIONS and the OWNER’S MANUAL safety precautions. The exact HT70 owner-safety source is not established in the retained archive inventory or HT70/HT75 document links; repair-manual safety paragraphs do not replace it. No start-up or under-load test was performed, and review closure is not bench readiness.
- Section 7 says HT70 parts will be incorporated in the existing HT75 list and are included in the 3.98 microfiche/CD-ROM issue. The retained 2012 catalog links HT70/HT75 to later IPL documents, including a gearhead entry marked 11.2005 and a gear-housing conversion kit marked 22.2011. No exact 3.98 edition is established by that index or the retained PDF inventory. Later drawings are useful navigation, not proof of 1998 parts, supersession, introduction serial, current stock or publication authorization. The copyright/footer adds no interchange assertion.
- Historical HT 70 only. TI35/1998 calls this series 4138; the retained exact-model IPL is filed under 4137. That navigation association does not establish series equivalence, extend these assertions to HT 75 or later variants, or prove physical interchange. No production serial or current stock claim is supplied. No hardware operation was performed.
Source: TI 35/1998, p. 3 · TI 35/1998, p. 4 — Sections 5.1, 6 safety paragraph, 6.1 and 7; retained dependency review complete with bounded exact-source gaps.
No additional parts-table entry added.
Service note · HT 70
HT 70: qualified-workshop repair times
Twenty HT70 labor allowances use decimal hours (0.1 = 6 minutes), for trained personnel in a properly equipped workshop; they are not procedural settings.
- The repair times assume TRAINED PERSONNEL in a PROPERLY EQUIPPED SERVICE WORKSHOP. Values are tenths of an HOUR, with 0.1 = 6 minutes; they are NOT decimal minutes, guaranteed elapsed times, torque values or permission to perform a repair.
- Codes 1–5: crankcase 2.1 h; crankshaft and/or bearings 2.2 h; crankcase gasket, sealing 2.0 h; crankshaft seals 0.7 h; cylinder and/or piston 0.8 h.
- Codes 6–10: ignition 0.5 h; fuel hose, fuel supply 0.5 h; REPLACE gear box assembly 0.5 h; carburetor 0.7 h; fan housing, clutch housing 0.8 h.
- Codes 11–15: front handle, throttle 0.6 h; recoil starter 0.5 h; clutch 0.5 h; REPLACE drive tube, shaft, bearings 0.5 h; muffler 0.4 h.
- Codes 16–20: air filter, filter cover 0.3 h; stop switch 0.4 h; fuel tank 0.4 h; REPLACE drive gears 0.7 h; all other repairs and miscellaneous repairs 0.5 h.
- The source says this HT70 table may update the STIHL repair-times table. Replacing the gearbox assembly and replacing drive gears are distinct rows, not interchangeable operations. The labor list does not provide their repair procedures or authorize hardware work.
- Historical HT 70 only. TI35/1998 calls this series 4138; the retained exact-model IPL is filed under 4137. That navigation association does not establish series equivalence, extend these assertions to HT 75 or later variants, or prove physical interchange. No production serial or current stock claim is supplied. No hardware operation was performed.
Source: TI 35/1998, p. 4 — Section 6.2 and all 20 table rows including unit heading and update note.
No additional parts-table entry added.
Wrong number or missing part for the HT 70, HT 75? Report a correction →