← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section D · 4 of 24 · 44 parts

Air filter, Fuel tank

Fits HT 70, HT 75.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131314151617181922021222324252627272833031323334343435353536455152535467889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (44)

PosPart numberDescriptionQty
1 4137 129 0905 Gasket 1
2 9007 319 1130 Hexagon head screw M5x62 2
3 4137 121 1601 Spacer flange Fitment / change note → 1
4 9291 021 0121 Washer 5.3 2
5 9022 341 1050 Spline screw IS-M5x25 2
6 4137 182 7600 Tensioner 1
7 4137 123 8900 Pin 1
8 9417 003 7512 Push nut 4.0x9.6x1.8 1
9 9022 313 0680 Spline screw IS-M4x16 1
10 4137 129 0900 Gasket 1
11 4137 120 0614 Carburetor C1Q-S157A 1
11 4137 120 0611 Carburetor C1Q-S80D 1
11 4137 120 0606 Carburetor C1Q-S63A 1
11 4137 120 0604 Carburetor C1Q-S56A 1
11 4137 120 0603 Carburetor C1Q-S45 1
12 4227 122 1805 Heat shield 1
13 4114 149 1205 Gasket Fitment / change note → 2
14 4137 140 2801 Filter housing Fitment / change note → 1
15 4137 141 3700 Lever 1
16 4137 141 3801 Choke shutter Fitment / change note → 1
17 9210 261 0700 Hexagon nut M5 2
18 4137 124 2800 Filter 1
19 4137 124 1500 Prefilter 1
20 4137 141 0500 Filter cover 1
21 4137 350 0410 Fuel tank 1
22 0000 989 0516 Grommet 2
23 not sold separately Hose 3.1x5.7x185 mm / 7 5/16'', R3 not available as a separate item 1
24 not sold separately Hose 3.1x5.7x135 mm, R3 not available as a separate item 1
25 4137 352 8100 Insert 1
26 4137 352 8105 Insert 2
27 0000 350 3502 Pickup body 1
28 0000 358 1800 Filter 1
30 0000 350 0900 Rope 1
31 0000 353 0800 Filler cap retainer 1
32 0000 967 3693 Warning pictogram Filler cap 1
33 9007 319 1137 Hexagon head screw M5x68 2
34 4119 122 1701 Distance plate 3
35 4227 122 1805 Heat shield 3
36 4114 149 1205 Gasket Fitment / change note → 1
51 4137 120 0600 Carburetor C1Q-S28E 1
52 4137 121 1600 Spacer flange Fitment / change note → 1
53 4137 140 2800 Filter housing Fitment / change note → 1
54 4137 141 3800 Choke shutter Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2803 Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85

Heat-shield sealing: one 4114 149 1205 gasket on each side

Fit missing gaskets on original-version machines; total quantity two.

  • Section 4 says 4114 149 1205 (1) has for some time been fitted ON BOTH SIDES OF HEAT SHIELD (2) to improve sealing. Drawing366TI023 GM places one gasket between carburetor and shield and another between shield and the air-filter side. The summary explicitly says GASKET (2x).
  • Service note: MISSING GASKETS MUST BE FITTED IN MODELS WITH THE ORIGINAL VERSION. Continuous introduction; no numeric cutoff. Do not stack both on one side, interpret2x as two pairs, invent a shield number or transfer this instruction to unlisted successor models.
  • The footer lists last TIs BG 75 TI 42.96 (TI 27.97 USA only), FC/FS/HL/HT TI 37.97 and HS TI 04.97. These are bibliographic history, not delegated procedures required to apply this gasket note; no missing-source closure claim is created from the footer alone.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 6 — Complete section 4, drawing 366TI023 GM, quantity 2 summary, service note and footer.

Part numbers (1)
  • 4114 149 1205 — Heat-shield gasket; drawing 1, quantity 2Fit missing gaskets · Only the named TI 41/1997 configurations and conditions

Service note · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85

FH/HL/HT/FC/FS: the 1999 engine upgrade is a matched set

Power rises from 0.9 to 0.95 kW; the filter housing, carburetor and spacer flange cannot be mixed across versions.

1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.

  • The source states an increase from 0.9 kW (1.2 bhp) to 0.95 kW (1.3 bhp), not a measured result from this project. Its exploded drawing labels carburetor 1, filter housing 2, spacer flange 3 and shroud 4; these drawing labels are not catalog positions or quantities.
  • The engine optimization changes the idle system and the four illustrated components. An unchanged engine displacement, top speed, emission rating or fuel ratio is not established by this power statement.
  • The later catalog stores these named machines' common engine assemblies under series 4137. That storage grouping does not revise the original cover's 4230 and 4138 product-series identities. Only exact source model tokens are bound.
  • The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
  • The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
  • For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
  • Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
  • TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.

Source: TI 21/1999, p. 1 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — Section 1 introduction and exploded engine drawing; 1.5.1–1.5.3; 1.5.7; serial and cover/colophon applicability.

No additional parts-table entry added.

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85

FH/HL/HT/FC/FS: filter housing and choke shutter must stay paired

New housing recesses aid felt-filter removal; the wider, smoother choke shutter belongs with the new housing.

1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.

  • The new housing and choke shutter are reshaped for increased air-flow volume. The new housing is identified by recesses (arrows in the right-hand drawing) that allow the felt filter element to be removed without tools. The left-hand drawing is the previous version. No measured flow increase or new filter-element number is supplied.
  • The new choke shutter has a smoother surface and is wider than the previous version. No width dimension is printed. Summary item 1 is a housing including item 2 (the choke shutter); all other parts remain as before. A separate shutter listing does not override the no-mixing rule.
  • The exact-model air-filter catalog sheets retain both pairs. This confirms where the historical evidence belongs; it does not establish current interchange or a replacement of every original housing by the new number.
  • The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
  • The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
  • For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
  • Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
  • TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.

Source: TI 21/1999, p. 1 · TI 21/1999, p. 2 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.1 including continuation on page 2; 1.5.1–1.5.3 and 1.5.7; summary rows 1–2 and remark 1.

Part numbers (4)
  • 4137 140 2800 — Filter housing, originalOriginal; includes original choke shutter · Original configuration; remains a spare under remark 1
  • 4137 140 2801 — Filter housing, newNew; includes new choke shutter · New configuration; summary item 1 includes item 2
  • 4137 141 3800 — Choke shutter, originalOriginal matched component · Only with original filter housing; remains a spare
  • 4137 141 3801 — Choke shutter, newNew matched component · Only with new filter housing

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85

FH/HL/HT/FC/FS: spacer flange 1600 and 1601 are configuration-specific

The original drawing labels 11.8 mm and 12.8 mm flow-section dimensions; these are not carburetor venturi diameters.

1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.

  • The left-hand original spacer flange (1) is annotated 11.8 mm / 0.46 in; the right-hand new flange (2) is annotated 12.8 mm / 0.50 in. The text says the fuel-air-mixture flow cross section is larger. The drawing supplies a linear dimension, not an area, machining allowance or instruction to enlarge the old part.
  • The carburetor paragraph separately says its new venturi is about 1 mm larger. The flange dimensions are not transcribed as the carburetor's absolute bore dimensions. No flow area, volume, gasket thickness or tolerance is inferred.
  • The exact-model catalog air-filter sheets retain both spacer-flange numbers. Historical summary remark 1 keeps the original available as a spare; the new number does not erase the original-machine replacement requirement.
  • The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
  • The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
  • For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
  • Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
  • TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.

Source: TI 21/1999, p. 1 · TI 21/1999, p. 2 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.3 spacer-flange comparison; 1.5.1–1.5.3 and 1.5.7; summary item 21, serial and remark 1.

Part numbers (2)
  • 4137 121 1600 — Spacer flange, originalOriginal version remains available as spare · Original engine configuration; summary item 21, remark 1
  • 4137 121 1601 — Spacer flange, newNew configuration component · New engine configuration; not a standalone universal upgrade

Wrong number or missing part for the HT 70, HT 75? Report a correction →