← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section L · 11 of 24 · 14 parts

Handle

Fits HT 70, HT 75.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11101112132233456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (14)

PosPart numberDescriptionQty
1 4137 790 0300 Handle Fitment / change note → 1
2 4137 791 9400 Hose clamp 2
3 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 2
4 4137 182 4505 Torsion spring Fitment / change note → 1
5 4137 182 1701 Slide control Fitment / change note → 1
6 4137 182 1001 Throttle trigger Fitment / change note → 1
7 4137 182 4504 Torsion spring Fitment / change note → 1
8 4137 182 0802 Lockout lever Fitment / change note → 1
9 4128 182 4501 Torsion spring Fitment / change note → 1
10 4128 793 3000 Slide Fitment / change note → 1
11 4128 791 3100 Spring 1
12 9074 478 3025 Pan head self-tapping screw IS-P4x16 4
13 4137 180 1107 Throttle cable Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 4137 790 1307 Control handle Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 controls: coordinated retrofit and ground connector

The new control handle needs the new cable and, on earlier machines, an added ignition-module ground connector.

  • The new control handle may be installed on previous machine versions only with the new throttle cable and a retrofitted ignition-module connector 4137 405 1600. The control handle and throttle cable remain separate replacement assemblies; buying a handle does not include the cable.
  • The new cable assembly comprises corrugated tube, cable and sealed microswitch with permanently connected water-tight short-circuit wires. Its individual parts, including the microswitch, are not separately supplied. Two fully insulated wires run directly to the ignition module; black connects to the primary-circuit connector, blue to the ground connector. Earlier machines require that ground connector to be mounted as well.
  • The handle is identified by its slide slot and gray-shaded non-slip surfaces in the diagram. The slide control operates the sealed ignition microswitch. Squeezing the trigger to its stop takes up cable slack: the sheath is attached to the slide, whose spring-loaded detent arm travels along the notched track. Initial installation requires adjustment; the instruction-manual chapter is referenced, and section 1.4.4 supplies the adjustment procedure within this TI. No missing manual is needed to establish this stated procedure.
  • The unrestricted interchangeability statement in section 2 concerns rewind-starter parts, not these coordinated control-handle changes.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 2 · TI 24/2002, p. 3 · TI 24/2002, p. 4 — Section1 introduction,1.1–1.2, summary item1 and1.4.1 wiring.

Part numbers (1)
  • 4137 405 1600 — Ignition-module ground connectorRequired retrofit on earlier machines · Named models and handle configuration only; coordinated retrofit conditions apply

Service note · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 controls: USA-production serial cutoffs

FS 80, FS 85 and HT 75 have separate USA cutoffs; KM 85 R is from production start.

  • USA production: FS 80 from serial 2 55 972 256; FS 85 from 2 55 809 184; HT 75 from 2 55 809 912. These are control-handle/throttle-cable changeovers, not whole-model production ranges, worldwide cutoffs or starter-rope changeovers.
  • KM 85 R: since start of production. Other models: introduction in progress. No numerical cutoff is supplied for those other models. Do not substitute one named model’s serial for another, or infer a separate serial for FS 85 RT/RX.
  • The printed USA production heading is preserved for this introduction table; the TI does not establish introduction timing for other production locations.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 3 · TI 24/2002, p. 4 — Section1.3 introduction table and model-specific scope.

No additional parts-table entry added.

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 loop-handle control parts and old cable availability

Handle 4137 790 1307 and cable 4137 180 1107 have distinct contents; old cable 1150 had an approximate 2009 supply limit.

  • Loop-handled FH 75, HL 75, HT 70/75, FC 75/85, KM 85 R, KW 85 and FS 75/80/85/85 RT/85 RX only. Old control handle 4137 790 1350 includes summary items 16,17,19,20,22–24; new 4137 790 1307 includes 9,18,19,21–25. Item 9 is shared slide 4128 793 3000 from the bike-handle portion of the table, not a missing loop-handle part.
  • Old inner molding 4137 790 1101 and outer molding 4137 791 0800 give way to the new arrangement using handle 4137 790 0300. Slide control 4137 182 1700 becomes 4137 182 1701; old contact spring 4137 442 1600 has no new individual counterpart. New torsion spring 4137 182 4505 is added.
  • Throttle trigger 4137 182 1000 becomes 4137 182 1001; torsion spring 4137 182 4500 becomes 4137 182 4504; interlock lever 4137 182 0801 becomes 4137 182 0802; torsion spring 4128 182 4501 is added.
  • Previous cables 4137 180 1103 and 4137 180 1150 are listed. The latter explicitly includes summary items 16 and 24 (inner molding and interlock lever); that unusual source description is retained, not silently changed to microswitch contents. New cable 4137 180 1107 includes item 29, the microswitch with short-circuit wires, not separately available or assigned an order number.
  • Remark 1 keeps marked previous parts available as spares for older machines. Remark 3 instead states that old cable 4137 180 1150 remains available from the factory up to about 2009. This is an approximate historical supply statement, not a model end date, exact discontinuation date or present-stock claim. All other parts remain as before.
  • Retrofitting the new handle requires the new cable plus ignition-module connector 4137 405 1600. Neither the table nor shared catalog sheets grants interchange between bike and loop handles.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 2 · TI 24/2002, p. 3 · TI 24/2002, p. 4 — Section1.3 summary items14–29 plus shared slide item9, remarks1–3.

Part numbers (21)
  • 4137 790 1350 — Control handlePrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 790 1307 — Control handleNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 790 1101 — Inner handle moldingPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 791 0800 — Outer handle moldingPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 790 0300 — HandleNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 1700 — Slide controlPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 1701 — Slide controlNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 442 1600 — Contact springPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 4505 — Torsion springNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 1000 — Throttle triggerPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 1001 — Throttle triggerNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 4500 — Torsion springPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 4504 — Torsion springNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 0801 — Interlock leverPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 0802 — Interlock leverNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 182 4501 — Torsion springNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 793 3000 — SlideShared summary item9 · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 180 1103 — Throttle cablePrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 180 1150 — Throttle cable including items16/24Previous; factory supply up to about2009 · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 180 1107 — Throttle cable assemblyNew; includes non-separate microswitch/wires · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 405 1600 — Ignition-module connectorCoordinated retrofit · Named models and handle configuration only; coordinated retrofit conditions apply

Service note · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 loop handle: cable routing and trigger spring installation

Route blue then black; the spring’s straight end goes under the cable sleeve.

  • Seat the microswitch as illustrated. Push the blue ground wire into the channel first, then the black short-circuit wire, right to the end. Neither wire may project. Put both in recess 20 at corrugated-tube 19 attachment; the throttle cable is placed over the recess later, as shown in the drawing.
  • Press cable 11 into slide 12 until ferrule 13 snaps into place. Position the slide in the molding with the groove at the end of the slot: the basic adjustment position.
  • Attach cable end sleeve 14 to trigger 15. Push the straight end of spring 16 under the end sleeve, then put the ring-shaped part over pivot 17 on the trigger. Fit the trigger and put the spring loop around screw boss 18. Do not substitute the bike-handle instruction placing the spring in front of the sleeve.
  • Check corrugated tube and slide position. Do not squeeze the throttle trigger until section 1.4.4 adjustment. Screw the moldings together without pinching wires, attach cable to carburetor and reassemble powerhead. Slide the control handle onto the drive tube, secure the tube to the powerhead, then align and secure the control handle before adjusting.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 6 · TI 24/2002, p. 7 — Section1.4.3 all diagrams and installation steps.

No additional parts-table entry added.

Service note · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 controls: throttle adjustment, rechecks and travel limit

Adjust only fully assembled in the working position; unresolved travel-limit slack requires a new cable.

  • The cable is no longer routinely adjusted at the tensioner. For correct semi-automatic operation, set its screw so visible thread lengths above and below are equal. If this basic setting does not allow satisfactory operation, the source permits a slight screw correction; no numerical thread length or number of turns is given.
  • Adjust only when the machine is completely and securely assembled, with handlebar and control handle in the normal operating position. Use a screwdriver to press down the slide and push it to the end of its slot. Then press the trigger interlock and squeeze the trigger fully: the slide moves away from the end and takes up slack automatically. Carburetor adjustment may then be necessary; the TI supplies no carburetor screw setting.
  • Correct cable adjustment is required at full throttle, starting throttle and idle. Recheck if the trigger was squeezed too early during handling/mounting, after service or repair, before carburetor readjustment, after a large bike-handlebar position change, after cable stretch, or if snagging force changed the slide position.
  • The travel limit is reached when the slide touches the opposite end of the slot but free play remains. With interlock depressed and trigger fully squeezed, check that the throttle-shaft lever touches the carburetor body. If not, readjust the tensioner to take up slack. If that does not remedy it, install a new throttle cable. Simply reaching the slot end is not proof of correct full-throttle operation.
  • These are retained offline service instructions, not a performed adjustment, engine actuation or a substitute for the machine-specific general safety and repair instructions.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 5 · TI 24/2002, p. 7 · TI 24/2002, p. 8 — Section1.4.1 tensioner basic setting and complete1.4.4 including diagrams.

No additional parts-table entry added.

Wrong number or missing part for the HT 70, HT 75? Report a correction →