← Brushcutters & other equipment · series 4140

Stihl 4140 · Section B · 2 of 15 · 15 parts

Rewind starter

Fits FC 55.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131423456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (15)

PosPart numberDescriptionQty
1 4140 190 4009 Rewind starter 1
2 4140 190 0601 Rewind spring Fitment / change note → 1
3 4128 195 0400 Rope rotor 1
4 0000 958 0923 Washer 1
5 1118 195 3500 Spring 1
6 4116 195 7200 Pawl 1
7 4140 195 3400 Starter grip 1
8 0000 190 3404 Starter grip ElastoStart Ø 3 mm option 1
9 1120 195 8200 Starter rope Ø 3x1060 mm Fitment / change note → 1
10 0000 195 7000 Cap option 1
11 0000 195 8200 Starter rope Ø 3x800 mm Fitment / change note → 1
12 4140 967 1502 Model plate FC 55 1
13 0000 951 1100 Screw IS-D5x20 3
14 4140 084 6801 Spacer 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2208 NLA Starter rope Ø 3 mm x 30.5 m not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · HL 45 / FC 55 / FS 55 / FS 45

HL 45, FC 55, FS 45/55: paired starter rope and spring

Longer rope requires the new spring; the source disagrees on its inch length.

  • Only the named HL 45, FC 55, FS 55 and FS 45 configurations are covered. Shared IPL sheets do not extend this note to FS 38/46 or unnamed C/L/R/RC/T variants. The HL 45 header says series 4232; 4140 powerhead navigation is not a series-equivalence claim.
  • Rewind starter 4140 190 4000 keeps its part number but changes construction with the carburetor update. New rope 1120 195 8200 is diameter 3 x 1060 mm and new rewind spring is 4140 190 0601, increasing pull length. The drawing shows old/new replacement springs in transport keepers.
  • The longer rope may only be installed together with the new rewind spring. Old rope 0000 195 8200 (diameter 3 x 800 mm, 31 1/2 inches) and old spring 4140 190 0600 remain for repairs to older machines. The old complete starter version is deleted despite the unchanged assembly number.
  • Unresolved source conflict: page7 prints 41 3/8 inches for the new 1060 mm rope; page8 prints 41 3/4 inches for the same rope. Both retain the same metric length and part number. Neither inch value is silently normalized or selected as authoritative.
  • The TI identifies the new carburetor as an easy indicator of machines with the new rope and spring. This is a historical production cue, not proof of an unmodified present-day machine or a blanket retrofit instruction.
  • Introduction of the overall model update is in progress, not a dated universal serial cutoff. Availability is historical 2001 factory supply, not current stock. No hardware fitment or operation was tested.

Source: TI 27/2001, p. 7 · TI 27/2001, p. 8 — Section2.8, spring/keeper drawing and summary rows28–31/remarks1,6.

Part numbers (5)
  • 4140 190 4000 — Rewind starterSame number, changed version · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 1120 195 8200 — 3 x 1060 mm starter ropeNew; conflicting inch lengths · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 4140 190 0601 — Rewind springRequired with longer rope · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 0000 195 8200 — 3 x 800 mm starter ropePrevious; retained · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 4140 190 0600 — Rewind springPrevious; retained · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply

Wrong number or missing part for the FC 55? Report a correction →