← Brushcutters & other equipment · series 4140

Stihl 4140 · Section G · 7 of 23 · 13 parts

Ignition system, Clutch

Fits FS 38, FS 45, FS 45 C, FS 45 L, FS 46, FS 46 C.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213234456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (13)

PosPart numberDescriptionQty
1 4140 400 1200 Flywheel Fitment / change note → 1
2 4140 162 8900 Washer Fitment / change note → 1
3 4140 162 9101 Spacer sleeve 1
4 4140 160 2005 Clutch 1
5 4140 162 7901 Tension spring 2
6 not sold separately Cup spring 31.7x20.4x0.4 not available as a separate item 1
7 4140 160 2903 Clutch drum Fitment / change note → 1
8 4140 400 1308 Ignition module 1
9 4140 400 1309 Ignition module 1
10 4140 400 1305 Ignition module 1
11 4140 400 1300 Ignition module Fitment / change note → 1
12 4140 431 2100 Connector tag 1
13 9075 478 3023 Pan head self-tapping screw IS-D4x22 2

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · FS 45

FS 45: series 4140 replacement ignition assignment

4140 400 1300 with flywheel 4140 400 1200; ignition lead not replaceable.

  • Printed series 4140. Use 4140 400 1300 with flywheel 4140 400 1200.
  • The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.

Part numbers (2)
  • 4140 400 1300 — Replacement ignition moduleAssigned component · FS 45, printed series 4140, listed combination only
  • 4140 400 1200 — Assigned flywheelRequired pairing · FS 45, printed series 4140

Conditional replacement · HL 45 / FC 55 / FS 55 / FS 45

HL 45, FC 55, FS 45/55: ignition and crankshaft restriction

Machines with carburetor 4140 120 0603 require the new ignition and crankshaft versions in repairs.

  • Only the named HL 45, FC 55, FS 55 and FS 45 configurations are covered. Shared IPL sheets do not extend this note to FS 38/46 or unnamed C/L/R/RC/T variants. The HL 45 header says series 4232; 4140 powerhead navigation is not a series-equivalence claim.
  • Ignition module 4140 400 1300 changes to 4140 400 1303 together with crankshaft 4140 030 0401 replacing 4140 030 0400. The flywheel-keyway position changes on the new crankshaft; the source attributes the pair to optimized timing and governor cut-off speed range, without numerical timing/speed values.
  • For repair of machines with carburetor 4140 120 0603, only the new versions of these parts may be used. Old module and crankshaft remain listed for older machines/other models; do not infer arbitrary mixed-generation interchangeability or substitute later IPL numbers as proven supersessions.
  • Introduction of the overall model update is in progress, not a dated universal serial cutoff. Availability is historical 2001 factory supply, not current stock. No hardware fitment or operation was tested.

Source: TI 27/2001, p. 5 · TI 27/2001, p. 7 · TI 27/2001, p. 8 — Section2.5, keyway illustration and summary rows15–16/remark1.

Part numbers (5)
  • 4140 400 1300 — Ignition modulePrevious · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 4140 400 1303 — Ignition moduleNew · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 4140 030 0400 — CrankshaftPrevious · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 4140 030 0401 — Revised-keyway crankshaftNew · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 4140 120 0603 — C1Q-S66 carburetorRequired new-version repair condition · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply

Conditional replacement · HL 45 / FC 55 / FS 55 / FS 45

HL 45, FC 55, FS 45/55: clutch with matching thinner washer

Replacement clutch is interchangeable as supplied with its 1.2 mm washer.

  • Only the named HL 45, FC 55, FS 55 and FS 45 configurations are covered. Shared IPL sheets do not extend this note to FS 38/46 or unnamed C/L/R/RC/T variants. The HL 45 header says series 4232; 4140 powerhead navigation is not a series-equivalence claim.
  • Clutch 4140 160 2000 is replaced by 4140 160 2001 with a cup spring bonded to the inboard side of the carrier. Cup spring dimensions are 31.7 x 20.4 x 0.4 as printed; it has no separate replacement number and is not supplied separately.
  • The washer between clutch and flywheel changes from 4130 162 8900 (1.5 mm) to 4140 162 8900 (1.2 mm). New replacement clutches include the thinner washer and are therefore fully interchangeable as that supplied combination. This is not permission to retain the thicker washer with the new clutch.
  • Previous clutch is deleted; previous washer remains listed for older machines/other models.
  • Introduction of the overall model update is in progress, not a dated universal serial cutoff. Availability is historical 2001 factory supply, not current stock. No hardware fitment or operation was tested.

Source: TI 27/2001, p. 6 · TI 27/2001, p. 8 — Section2.7, exploded diagram and summary rows25–27/remarks1,5,6.

Part numbers (4)
  • 4140 160 2000 — ClutchPrevious; deleted · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 4140 160 2001 — Clutch with bonded cup springNew; includes thinner washer · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 4130 162 8900 — 1.5 mm washerPrevious · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
  • 4140 162 8900 — 1.2 mm washerNew matched washer · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply

Conditional replacement · HL 45 / FC 55 / FS 45 / FS 55 / KM 55

FC 55, FS 45/55, KM 55: revised clutch drum; HL 45 excluded

HL 45 retains its previous drum in all versions; the other named models receive the revision.

  • Only the named HL 45, FC 55, FS 45, FS 55 and KM 55 configurations are covered, with the section-specific HL 45 exclusion below where stated. Shared IPL sheets do not extend this note to FS 38/46 or unnamed C/L/R/RC/T variants. HL 45 is headed series 4232; navigation through 4140 powerhead sheets is not series equivalence.
  • For FC 55, FS 45, FS 55 and KM 55, clutch drum 4140 160 2901 is replaced by 4140 160 2903 to optimize clutch operation. Previous drum 4140 160 2901 remains available as a spare.
  • The change explicitly excludes HL 45: 4140 160 2901 continues to be installed in all HL 45 versions. The HL 45 navigation target exists to display this exclusion, not to authorize 4140 160 2903 on that machine.
  • Introduction is in progress, with no numerical serial cutoff. Factory availability is the historical 2002 statement, not current stock. Later IPL numbers do not overwrite historical numbers or prove unrestricted interchangeability. No hardware operation or fitment was tested.

Source: TI 36/2002, p. 2 · TI 36/2002, p. 3 — Section3 and summary row11/remarks2,4.

Part numbers (2)
  • 4140 160 2901 — Clutch drumPrevious; retained for all HL45 versions and as spare · Named models only; section-specific restrictions apply
  • 4140 160 2903 — Clutch drumNew; not HL45 · Named models only; section-specific restrictions apply

Wrong number or missing part for the FS 38, FS 45, FS 45 C, FS 45 L, FS 46, FS 46 C? Report a correction →