← Brushcutters & other equipment · series 4140

Stihl 4140 · Section A · 1 of 19 · 23 parts

Crankcase, Cylinder

Fits KM 55, KM 55 C, KM 55 R, KM 55 RC.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121213141516171819222021334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 4140 021 0300 Crankcase 1
2 9639 003 1230 Oil seal 12x22x7 2
3 9503 003 0246 Grooved ball bearing 6201 2
4 4140 036 0300 Washer 2
5 4140 030 0401 Crankshaft 1
6 4140 029 2300 Cylinder gasket 1
7 4140 021 2500 Engine pan 1
8 4140 020 1202 Cylinder with piston Ø 34 mm 1
9 4140 020 1200 NLA Cylinder with piston Ø 34 mm → replaced by 4140 020 1202 TI 23/2003 1
10 4140 030 2000 Piston Ø 34 mm 1
11 4137 034 3000 Piston ring Ø 34x1.5 mm 2
12 9463 650 0807 Snap ring 8x0.7 2
13 4137 034 1500 Piston pin 8x5x22 1
14 9075 478 4268 Pan head self-tapping screw IS-D5x60 4
15 4140 195 0601 Starter cup Fitment / change note → 1
16 4117 162 8900 Washer Fitment / change note → 1
17 4140 190 2010 Driver 1
18 0000 998 0612 Torsion spring 2
19 4133 195 7201 Pawl 2
20 0000 400 7000 Spark plug NGK BPMR7A 1
20 1110 400 7005 Spark plug Bosch WSR 6 F 1
21 0783 830 2000 Tube of sealant Dirko HT red option 1
Not numbered on the diagram — assemblies, kits and options
— 4140 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · HL 45 / FC 55 / FS 45 / FS 55 / KM 55

HL 45, FC 55, FS 45/55, KM 55: starter cup generations and washer

Unnumbered separate-nut production revision is distinct from the numbered repair conversion.

  • Only the named HL 45, FC 55, FS 45, FS 55 and KM 55 configurations are covered, with the section-specific HL 45 exclusion below where stated. Shared IPL sheets do not extend this note to FS 38/46 or unnamed C/L/R/RC/T variants. HL 45 is headed series 4232; navigation through 4140 powerhead sheets is not series equivalence.
  • On the production line, starter cup 4140 195 0601 with integrated nut is replaced by a version with a separate nut. The TI gives no separate part number for that production version; do not invent one. Cup 4140 195 0601 remains supplied as a replacement.
  • A separate repair note concerns older starter cup 4140 190 0500: some versions had washer 4117 162 8900 between that cup and the oil seal. This washer is not required if replacement cup 4140 195 0601 is installed during repair. Do not omit washers universally or confuse the older 0500-to-0601 repair change with the separate-nut production revision.
  • Introduction is in progress, with no numerical serial cutoff. Factory availability is the historical 2002 statement, not current stock. Later IPL numbers do not overwrite historical numbers or prove unrestricted interchangeability. No hardware operation or fitment was tested.

Source: TI 36/2002, p. 3 — Section4 including service note.

Part numbers (3)
  • 4140 195 0601 — Integrated-nut starter cupProduction version replaced; retained repair replacement · Named models only; section-specific restrictions apply
  • 4140 190 0500 — Earlier starter cupSome versions use washer · Named models only; section-specific restrictions apply
  • 4117 162 8900 — WasherNot required with 0601 repair replacement · Named models only; section-specific restrictions apply

Wrong number or missing part for the KM 55, KM 55 C, KM 55 R, KM 55 RC? Report a correction →