← FS 25-4, FS 65-4

Stihl 4170 · Section J · 9 of 14 · 22 parts

Control handle

Fits FS 25-4, FS 65-4.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141415161617171818181819222033456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (22)

PosPart numberDescriptionQty
1 4137 790 1101 Handle molding, inner 1
2 4137 791 9400 Hose clamp 2
3 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 2
4 4137 442 1600 Contact spring 1
5 4137 182 1700 Slide control 1
6 4137 182 1000 Throttle trigger 1
7 4137 182 4500 Torsion spring 1
8 4137 182 0801 Lockout lever 1
9 4137 182 4502 Torsion spring 1
10 4137 791 0800 Handle molding, outer 1
11 9074 478 3025 Pan head self-tapping screw IS-P4x16 4
12 4170 180 1105 Throttle cable 1
13 not sold separately Hose 200 mm / 7 7/8'' not available as a separate item 1
14 4130 790 1315 Loop handle 1
15 4130 790 8450 Barrier bar 1
16 9222 068 0900 Square nut M6 2
17 9022 341 1370 Spline screw IS-M6x30 2
18 4123 791 7400 Clamp 2
19 9291 021 0140 Washer 6.4 2
20 9022 341 1350 Spline screw IS-M6x25 2
Not numbered on the diagram — assemblies, kits and options
— 4137 790 1350 Control handle 1
— 4203 711 7201 Hose 960 mm / 37 13/16'' 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 25-4 / FS 65-4

FS 25-4 / FS 65-4: handle-specific noise and vibration

Eight measured configurations remain separate; the loop-handle metal rows require a barrier bar.

  • Page 5 table columns below are: sound pressure Lpeq to ISO 7917 / sound power Lweq to ISO 10884, both dB(A); then vibration to ISO 7916 in m/s² at IDLE right/left handle and MAXIMUM RPM right/left handle. Noise footnote 1 uses equal-duration exposure to idling and racing for the weighted equivalent level; this is not peak noise or a current certification claim.
  • Footnote 2 means BIKE HANDLE; footnote 3 means LOOP HANDLE; footnote 4 means LOOP HANDLE WITH BARRIER BAR. The R notation appears in the source rows, while the catalog groups these models on shared sheets. Measurement configurations do not authorize additional cutting tools.
  • FS 25-4 bike / nylon: pressure/power 88/101 dB(A); idle R/L 2.3/2.6 m/s²; maximum RPM R/L 4.4/4.3 m/s².
  • FS 25-4 bike / metal: pressure/power 89/98 dB(A); idle R/L 2.3/2.6 m/s²; maximum RPM R/L 3.6/3.5 m/s².
  • FS 25-4R loop / nylon: pressure/power 89/101 dB(A); idle R/L 2.0/2.3 m/s²; maximum RPM R/L 7.4/5.4 m/s².
  • FS 25-4R loop WITH BARRIER / metal: pressure/power 90/98 dB(A); idle R/L 2.0/2.3 m/s²; maximum RPM R/L 11.0/5.8 m/s².
  • FS 65-4 bike / nylon: pressure/power 92/103 dB(A); idle R/L 0.9/1.4 m/s²; maximum RPM R/L 3.8/3.9 m/s².
  • FS 65-4 bike / metal: pressure/power 92/102 dB(A); idle R/L 0.9/1.4 m/s²; maximum RPM R/L 3.6/3.8 m/s².
  • FS 65-4R loop / nylon: pressure/power 91/102 dB(A); idle R/L 1.7/2.3 m/s²; maximum RPM R/L 9.1/6.1 m/s².
  • FS 65-4R loop WITH BARRIER / metal: pressure/power 91/100 dB(A); idle R/L 1.7/2.3 m/s²; maximum RPM R/L 10.7/6.0 m/s².
  • Historical TI14/1998, series 4170: FS 25-4 and FS 65-4 only, with stated handle restrictions. Not FS 25/FS 65 two-strokes or later 4-MIX engines. No serial cutoff or current-stock promise is supplied. No hardware operation was performed.

Source: TI 14/1998, p. 5 — Page 5 all eight noise/vibration rows, column standards and four footnotes.

No additional parts-table entry added.

Wrong number or missing part for the FS 25-4, FS 65-4? Report a correction →