Stihl 4203 · Section J · 9 of 10 · 29 parts
Control handle
Fits BR 320, BR 320 L, BR 400.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (29)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4203 790 1102 | Handle molding, inner 67 mm / 2 5/8" | 1 |
| 2 | 4203 182 0801 | Locking lever | 1 |
| 3 | 4203 182 8950 | Pin | 1 |
| 4 | 9291 021 3865 | Washer 6.1x22x2 | 2 |
| 5 | 9322 630 0715 | Spring washer 6.2x19x1.2 | 2 |
| 6 | 9291 021 3864 | Washer 6.1x22x2 | 1 |
| 7 | not sold separately | Locking washer 4 not available as a separate item | 1 |
| 8 | 4203 791 0804 | Handle molding, outer 67 mm | 1 |
| 9 | 4203 182 1000 | Throttle trigger | 1 |
| 10 | 4203 121 2500 | Slide | 1 |
| 11 | 4203 442 1600 | Contact spring | 1 |
| 12 | 9104 003 0660 | Self-tapping screw P4x12 | 1 |
| 13 | 4203 791 5200 | Bushing | 1 |
| 14 | 4203 180 1111 | Throttle cable | 1 |
| 15 | not sold separately | Short circuit wire 1215 mm / 47.8'' not available as a separate item | 1 |
| 16 | not sold separately | Short circuit wire 1120 mm / 44.1'' not available as a separate item | 1 |
| 17 | 0751 030 8207 | Terminal socket 4-1 no longer available from factory | 2 |
| 18 | 0751 030 8404 | Terminal socket 6.3-1 no longer available from factory | 2 |
| 19 | not sold separately | Hose 780 mm / 30 3/4'' | 1 |
| 20 | 4203 711 7203 | Hose 160 mm / 6 5/16'' | 1 |
| 21 | 0751 030 8957 | Terminal socket 4.8-1/0.8 no longer available from factory | 1 |
| 22 | 4203 440 1900 | Lead 90 mm / 3.5'' | 1 |
| 23 | 9074 478 3075 | Pan head self-tapping screw IS-P4x19 | 5 |
| 24 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 1 |
| 25 | 9460 624 0501 | E-clip 5 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4203 790 1302 | Control handle Ø 67 mm → replaced by 4203 790 1304, 4203 790 1306 TI 46/2001 | 1 |
| — | 4203 440 1102 | Short circuit wire | 1 |
| — | 0751 010 1110 | Lead 10 m / 33' option | 1 |
| — | 4203 711 7201 | Hose 960 mm / 37 13/16'' Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · BR 320 / BR 400 / SR 320 / SR 400
BR / SR 320, 400: installing sleeve for control-handle E-clip
4203 893 4600 assists installation of the E-clip and spring washers on the locking-lever pivot pin.
- TI18/1998 names BR/SR 320 and 400 blowers and sprayers, series 4203. Installing sleeve 4203 893 4600 is available to SIMPLIFY INSTALLATION of the E-clip AND spring washers on the pivot pin of the locking lever in the control handle. It is a servicing tool, not a replacement locking lever, pivot pin or machine-mounted sleeve.
- Figure 352TI004 KN depicts the hollow cylindrical installing sleeve and its cutaway end. No dimensions, material, manufacturing drawing, washer stacking order or step-by-step installation are specified. The picture alone is not a fabrication or assembly specification.
- The retained SCS 01-2012 USA J control-handle sheets provide exact BR 320/400 and SR 320/400 context. The BR sheet also names BR 320 L; that shared sheet does not extend this bulletin’s explicitly named recipients to the L variant. No 340/420 successor binding is added. The sleeve is not listed as an installed part in either J sheet.
- The retained bulletin metadata title mentions Carburetor; Fuel Tank, but the original contents and page cover only the installing sleeve and dusting/spreading air filters. Those metadata words do not establish additional source sections. Last-TI24/1997 is a bibliographic locator, not a dependency for this sleeve claim.
- Historical source guidance only; no present-day stock or conformity guarantee and no verified physical interchange. No hardware operation was performed.
Source: TI 18/1998, p. 1 — Heading, contents, complete section1 and sleeve figure352TI004 KN; last-TI locator.
Part numbers (1)
- 4203 893 4600 — Installing sleeveServicing tool for E-clip and spring-washer installation · BR 320 / BR 400 / SR 320 / SR 400 locking-lever pivot
Conditional replacement · BR 320 / BR 400 / SR 320 / SR 400
BR/SR 320, 400: cut the replacement cable hose to 780 + 180 mm
Cable 4203 180 1101 keeps its number; production uses two hose lengths while the 960 mm hose remains the replacement stock.
in progress — Production introduction announced without a serial threshold.
- The one-piece 960 mm hose previously fitted over throttle cable 4203 180 1101 is no longer used on the production line; two hoses are fitted over the new cable version. The table repeats 4203 180 1101 in both columns and states that only the modified cable is available from the factory. An unchanged part number does not establish an unchanged configuration.
- To simplify stockkeeping, hose 4203 711 7201 remains the replacement. Cut it into 780 mm and 180 mm lengths before installation. Items 3 and 4 are not available separately; the printed -*- markers are not orderable part numbers. No cutting tolerance, hose-routing sequence or alternative length is supplied.
- The summary describes cable item 1 as including items 2 to 4, while the prose distinguishes one-piece replacement stock from two production lengths. Preserve that printed inclusion range without interpreting it as three simultaneously installed hoses or three separately supplied hose parts.
- Later-catalog differences retained: both exact-model control-handle sheets list cable 4203 180 1111 at position 14, unnumbered 780 mm hose at position 19, and hose 4203 711 7203 described as 160 mm at position 20; they also retain unpositioned 960 mm stock 4203 711 7201. TI23 instead prints cable 1101 and a 180 mm short length. The later rows do not prove a cable supersession, justify substituting 160 mm for 180 mm, or assign 7203 to the TI unnumbered short hose.
- The original heading covers BR 320, BR 400, SR 320 and SR 400, series 4203. The shared BR catalog sheet also names BR 320 L; this note does not infer that variant or later 340/380/420 applicability.
- Both changes are announced as in progress, with no serial threshold. The 1999 factory-supply statements are historical, not present stock claims or proof of the configuration now fitted.
Source: TI 23/1999, p. 2 — 2 Throttle cable (hose); complete production, parts-availability, summary and remarks.
Part numbers (2)
- 4203 180 1101 — Throttle cableSame previous/new number; only modified version supplied · Section 2 item 1, including items 2 to 4
- 4203 711 7201 — Hose (960 mm)Retained replacement; cut to 780 mm and 180 mm before installation · Section 2 item 2
Wrong number or missing part for the BR 320, BR 320 L, BR 400? Report a correction →