← TS 460

Stihl 4221 · Section T · 18 of 20 · 5 parts

Tools

Fits TS 460.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1234
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (5)

PosPart numberDescriptionQty
1 4128 890 3400 Combination wrench 1
2 5910 890 2305 Screwdriver 1
3 4130 893 7800 Locking pin 1
4 0000 891 0801 NLA Tool roll 1
Not numbered on the diagram — assemblies, kits and options
— 4223 890 1400 Tool kit 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 460

TS 460 weight and dimensions: wheel-installed and wheel-absent conditions

11.3 kg without fuel or wheel, with 300 mm attachment; 750 mm length includes the wheel.

  • Page 8 qualifies the 11.3 kg (24.9 lb) weight: machine WITHOUT FUEL, complete with attachment for a 300 mm (12 in) wheel, but WITHOUT THE CUTTING WHEEL. It is not the complete running weight, nor an explicit 350 mm configuration weight.
  • The 750 mm (29.5 in) length DOES include a 300 mm (12 in) wheel. Width with handle is 300 mm (12 in); height to handle is 370 mm (14.5 in). Do not apply the weight exclusion to the dimension configuration.
  • The standard accessories listed in section 5.6 are combination wrench, locking pin and screwdriver, without part numbers. That generic locking-pin listing is not an exception to the explicit new-locking-strip requirement for blocking the TS 460 crankshaft in section 6.1.
  • Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.

Source: TI 43/1995, p. 8 — TS 460 weight and dimensions: wheel-installed and wheel-absent conditions.

No additional parts-table entry added.

Service note · TS 460

TS 460 ignition and fastener tools: torque-wrench variants stay distinct

0.5–18 Nm and 6–80 Nm ranges; only 0302/0312 have optical/acoustic warnings.

  • Flywheel puller 1116 893 0800 removes the flywheel; crimping tool 5910 890 8210 attaches electrical wiring connectors; setting gauge 1111 890 6400 sets ignition-module/flywheel air gap. Size-13 insert 5910 893 5608 serves the FLYWHEEL NUT, whereas size-17 insert 5910 893 5610 serves the STARTER-WHEEL NUT.
  • The printed abbreviated torque-wrench entries 5910 890 0301/02 and 5910 890 0311/12 denote respective variants 0301 and 0302 (0.5–18 Nm), and 0311 and 0312 (6–80 Nm). Only versions 5910 890 0302 and 5910 890 0312 are explicitly fitted with an OPTICAL/ACOUSTIC warning device. Range overlap does not make these versions identical.
  • Remark 1 requires a TORQUE WRENCH when tightening DG screws. Insert 1-5 × 120 × 6.3, 0812 542 2104, is for socket-head screws with internal star; T-handle screwdriver Q1-5 × 150, 5910 890 2400, is listed for hexagon socket-head screws. Preserve these printed tool labels; do not silently equate the two drive forms.
  • Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.

Source: TI 43/1995, p. 9 — TS 460 ignition and fastener tools: torque-wrench variants stay distinct.

Part numbers (11)
  • 1116 893 0800 — Flywheel pullerspecified · TS 460 service tools; not fastener torque settings
  • 5910 890 8210 — Electrical connector crimping toolspecified · TS 460 service tools; not fastener torque settings
  • 1111 890 6400 — Ignition air-gap setting gaugespecified · TS 460 service tools; not fastener torque settings
  • 5910 893 5608 — Size-13 flywheel-nut insertspecified · TS 460 service tools; not fastener torque settings
  • 5910 893 5610 — Size-17 starter-wheel-nut insertspecified · TS 460 service tools; not fastener torque settings
  • 5910 890 0301 — 0.5–18 Nm torque wrenchspecified · TS 460 service tools; not fastener torque settings
  • 5910 890 0302 — 0.5–18 Nm torque wrench with optical/acoustic warningspecified · TS 460 service tools; not fastener torque settings
  • 5910 890 0311 — 6–80 Nm torque wrenchspecified · TS 460 service tools; not fastener torque settings
  • 5910 890 0312 — 6–80 Nm torque wrench with optical/acoustic warningspecified · TS 460 service tools; not fastener torque settings
  • 0812 542 2104 — Internal-star screw insert 1-5 × 120 × 6.3specified · TS 460 service tools; not fastener torque settings
  • 5910 890 2400 — T-handle screwdriver Q1-5 × 150specified · TS 460 service tools; not fastener torque settings

Service note · TS 460

TS 460 drive servicing tools: two press arbors and two circlip pliers

1119/4119 arbors have different applications; A10/C19 pliers distinguish outer and inner circlips.

  • Assembly hook 5910 893 8800 removes pick-up bodies; assembly hook 5910 890 2800 detaches the CLUTCH SPRING; assembly tool 0000 890 2201 flares the rope guide bush. Similar names do not establish interchange.
  • Pliers A10, 0811 611 8200, serve the OUTER circlip on the thrust washer. Pliers C19, 0811 641 8380, serve the INNER circlip on the spindle bearing and crankshaft.
  • Press arbor 1119 893 7200 INSERTS AND REMOVES the needle sleeve in the V-belt pulley. Press arbor 4119 893 7200 PRESSES OUT the deep-groove ball bearings in the spindle bearing. Preserve the 1119/4119 prefixes and the different stated operations; the latter is not an explicit installation-tool approval.
  • Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.

Source: TI 43/1995, p. 9 — TS 460 drive servicing tools: two press arbors and two circlip pliers.

Part numbers (7)
  • 5910 893 8800 — Pick-up-body assembly hookspecified · TS 460; only the specified service application
  • 5910 890 2800 — Clutch-spring assembly hookspecified · TS 460; only the specified service application
  • 0000 890 2201 — Rope guide bush flaring toolspecified · TS 460; only the specified service application
  • 0811 611 8200 — Pliers A10 for outer circlipspecified · TS 460; only the specified service application
  • 0811 641 8380 — Pliers C19 for inner circlipspecified · TS 460; only the specified service application
  • 1119 893 7200 — Needle-sleeve press arborspecified · TS 460; only the specified service application
  • 4119 893 7200 — Spindle-bearing removal press arborspecified · TS 460; only the specified service application

Service note · TS 460

TS 460 historical repair times: minutes, missing entries and loaded trials

25 task rows; dash entries remain unspecified, not zero; starred rows require trial run under load.

  • The source times are MINUTES for duly trained professionals in a perfectly equipped service shop, not owner estimates, measured project results or promised billing times. The table is labelled TS 460 / 4221. Its dotted cut-out is intended for page 9 of the historical STIHL repair-time table; the available 2012 master is a later edition, not silently substituted.
  • Rows 1–10: (1) installing/removing engine 5; (2) guard 5; (3) motor arm 25; (4) V-belt pulley on cutting wheel 10; (5) shaft 15; (6) deep-groove ball bearing on cutting wheel 15; (7) V-belt pulley on clutch side —; (8) pin —; (9) deep-groove ball bearing on clutch side —; (10) cast arm 15. The THREE DASHES are UNSPECIFIED, not zero minutes or proof the repair is impossible.
  • Rows 11–18: (11) pressure-testing crankcase* 140; (12) pressure-testing crankshaft, bearing* 140; (13) pressure-testing sealing rings* 65; (14) testing crankcase for leaks, trial run 30; (15) pressure-testing cylinder, pistons* 60; (16) ignition system, contact* 20; (17) fuel supply, tank venting, tank, trial run 20; (18) pressure-testing manifold or flange 20. These are the printed operation labels, not instructions to pressure-test isolated mechanical parts or hold pressure for that many minutes.
  • Rows 19–25: (19) carburetor, testing* 35; (20) starter with trial run 15; (21) clutch, trial run 20; (22) handle frame, handle, handle housing, shroud, with trial run IN EACH CASE 25; (23) muffler 10; (24) air filter 5; (25) stop switch with trial run 10. Row 22 is not a single combined four-component job.
  • The asterisk means TRIAL RUN UNDER LOAD and applies only to rows 11, 12, 13, 15, 16 and 19. Other explicit trial-run labels remain present but do not acquire that footnote automatically. No test duration, test load, procedure or authorization to run hardware is inferred.
  • Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.

Source: TI 43/1995, p. 10 — TS 460 historical repair times: minutes, missing entries and loaded trials.

No additional parts-table entry added.

Service note · TS 460

TS 460 servicing aids: two greases and two threadlockers have different uses

Loctite 270 carburetor uses differ from Loctite 243 muffler use; gasket chart remains an external dependency.

  • Lubricating grease 0781 120 1111 is listed for rotary shaft seals and the needle sleeve in the V-belt pulley. STIHL multi-purpose grease 0781 120 1109 is separately listed for the HIGH-VOLTAGE CONNECTION ON THE IGNITION MODULE. Do not transpose these similar numbers/applications.
  • Threadlocking adhesive, solid (Loctite 270), 0786 111 1109, is listed for the throttle-shutter fastening screw and carburetor sealing plug. Loctite 243, 0786 111 1101, is listed for the muffler/engine-housing screw connection. The two adhesives are NOT presented as interchangeable.
  • Dirko sealing compound, 100 g, 0783 830 2120, is for crankcase sealing faces and the EXTERIOR of rotary shaft seals. The entry supplies no bead size, cure interval or substitute-product approval.
  • HTR ignition lead 0000 930 2251 is listed as 10 m (33 ft) stock; this is not the fitted lead length, which page 7 separately specifies as 360 mm. Gasket Chart 0457 281 6202 is listed without its contents. No exact chart was identified by the bounded retained PDF filename inventory; do not fabricate gasket-selection guidance.
  • The closing imprint dates this TI September 6, 1995, Waiblingen. Its document credits/copyright identify the source, not present supply or new publication authorization.
  • Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.

Source: TI 43/1995, p. 12 — TS 460 servicing aids: two greases and two threadlockers have different uses.

Part numbers (7)
  • 0781 120 1111 — Lubricating grease for shaft seals and pulley needle sleevespecified · TS 460 historical servicing-aid list; application restrictions in note
  • 0786 111 1109 — Loctite 270 threadlocking adhesivespecified · TS 460 historical servicing-aid list; application restrictions in note
  • 0786 111 1101 — Loctite 243 threadlocking adhesivespecified · TS 460 historical servicing-aid list; application restrictions in note
  • 0783 830 2120 — Dirko sealing compound, 100 gspecified · TS 460 historical servicing-aid list; application restrictions in note
  • 0781 120 1109 — STIHL multi-purpose grease for high-voltage connectionspecified · TS 460 historical servicing-aid list; application restrictions in note
  • 0000 930 2251 — HTR ignition lead, 10 m (33 ft) stockspecified · TS 460 historical servicing-aid list; application restrictions in note
  • 0457 281 6202 — Gasket Chart; contents not establishedspecified · TS 460 historical servicing-aid list; application restrictions in note

Wrong number or missing part for the TS 460? Report a correction →