← HS 72, HS 74, HS 76 · HS 75, HS 80, HS 85

Stihl 4226 · Section E · 5 of 17 · 34 parts

Carburetor C1Q-S29D

Fits HS 75, HS 80, HS 85.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232425262728293303132456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (34)

PosPart numberDescriptionQty
1 4226 120 7100 Throttle shaft with lever 1
2 1123 122 3000 Spring 1
3 4226 121 3300 Throttle shutter 1
4 1120 122 7400 Round head screw 1
5 1125 122 9001 E-clip 1
6 4119 121 8900 Pin 1
7 1120 122 9000 E-clip 1
8 1129 121 4800 Pump diaphragm 1
9 1123 129 0905 Gasket 1
10 1123 121 0800 End cover 1
11 1120 122 7800 Oval head screw 1
12 4116 121 5100 Inlet needle 1
13 1123 122 3001 Spring 1
14 1125 121 5000 Inlet control lever 1
15 1120 121 9200 Spindle 1
16 1120 122 6600 Collar screw 1
17 4129 129 0902 Gasket Fitment / change note → 1
18 4129 121 4700 Metering diaphragm Fitment / change note → 1
19 4226 120 2200 Flange Fitment / change note → 1
20 1128 122 7100 Screw Fitment / change note → 2
21 4226 122 6800 Low speed adjustment screw 1
22 4226 122 7100 Screw Fitment / change note → 2
23 1120 122 3005 Spring 1
24 1123 121 7800 Strainer 1
25 4137 121 5400 Valve jet 1
26 4226 121 0700 Cup plug 1
27 4226 121 0800 End cover Fitment / change note → 1
28 4226 121 2700 Cap 1
29 4226 121 8600 Washer 1
30 4226 120 8700 Control valve 1
31 1123 122 6200 Idle speed adjustment screw 1
32 1125 122 4200 Clamp 1
Not numbered on the diagram — assemblies, kits and options
— 4226 120 0602 Carburetor C1Q-S29D Fitment / change note → 1
— 4227 007 1060 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · HS 75 / HS 80 / HS 85

HS 75/80/85: flange kit and governor-valve distinction

The old carburetors remain two-screw versions; spare support uses the four-screw kit.

  • The two-screw end cover can distort the primer flange and metering diaphragm. The revised end cover and flange use four screws. On previous carburetors, exchange flange and cover together with the two additional longer screws; do not change only one component.
  • Unresolved screw-number conflict: page 3 prose specifies 4226 121 7100; page 4 summary item 9 specifies 4226 122 7100, quantity increased from two to four. Both original scans agree with their respective text. Neither number is silently corrected or certified as the right screw.
  • Page 3 drawing identifies A screws, B/B1 old/new end cover, C/C1 old/new flange, D metering diaphragm and E gasket. Kit comprises A, B1, C1, D, E. Page 4 instructs finger-tight insertion, then alternate diagonal tightening. No torque is stated; separately supplied kit installation instructions are referenced but were not located in the retained STIHL service documentation document index/resources or supplemental manual PDFs. Later workshop flange sections are not the exact kit instructions; this remains a documented source gap.
  • Common unchanged diaphragm 4129 121 4700 and gasket 4129 129 0902 remain listed. Previous two-screw item 8 is 1128 122 7100; item 9 is 4226 122 7100. Old end cover 4226 121 0800 remains a spare for other models; the new end cover and flange are not separate supply items. Summary asterisks/dashes are not new order numbers.
  • HS 75, 80, 85 previous carburetors had not changed over to four-screw flanges, but factory spare supply uses 4140 120 2250 flange kit (item 16, see item 3). No C1Q-S56 or C1Q-S63 assignment to HS models is made.
  • C1Q-S29, 4226 120 0602, has a governor valve; C1Q-S42, 4226 120 0604, has no governor valve. Both include summary items 4–9. The summary prints dash for new S29 and asterisk for new S42; neither is a replacement number. Remark 5 says unmodified versions supplied until existing stocks exhausted. Other parts remain as before.
  • The retained IPL sheets name S29D and S42C; these are exact-model family navigation only, not proof of suffix equivalence. The kit is not evidence that the governor-equipped and governor-free carburetors are interchangeable.
  • Only explicitly named models and configurations are covered. Shared IPL pages do not extend these assertions to unnamed R/RX or other variants. Availability statements describe 2001 factory support, not present stock. The printed cover places FH/HL under 4230, HT under 4138 and KW under 4602; retained exact-model engine sheets use 4137 as navigation, not proof of series equivalence.

Source: TI 16/2001, p. 3 · TI 16/2001, p. 4 · TI 16/2001, p. 5 — Sections 3.1, 3.1.3–3.1.5: HS exception, all HS summary rows and remarks.

Part numbers (10)
  • 4226 120 0602 — Carburetor C1Q-S29With governor valve · HS 75, HS 80, HS 85; named configuration only
  • 4226 120 0604 — Carburetor C1Q-S42Without governor valve · HS 75, HS 80, HS 85; named configuration only
  • 4140 120 2250 — Flange kitItem 16 references item 3 · HS 75, HS 80, HS 85; named configuration only
  • 4226 120 2200 — Previous flange, item 5Replaced through kit · HS 75, HS 80, HS 85; named configuration only
  • 4226 121 0800 — Previous end coverRemains for other models; new cover not separate · HS 75, HS 80, HS 85; named configuration only
  • 4129 121 4700 — Metering diaphragmUnchanged · HS 75, HS 80, HS 85; named configuration only
  • 4129 129 0902 — GasketUnchanged · HS 75, HS 80, HS 85; named configuration only
  • 1128 122 7100 — Previous screw, item 8Two in old arrangement · HS 75, HS 80, HS 85; named configuration only
  • 4226 122 7100 — Screw, summary item 9Four in new arrangement; conflicts with prose · HS 75, HS 80, HS 85; named configuration only
  • 4226 121 7100 — Longer screw as printed in proseUnresolved conflict with summary · HS 75, HS 80, HS 85; named configuration only

Wrong number or missing part for the HS 75, HS 80, HS 85? Report a correction →