Stihl 4229 · Section K · 9 of 17 · 10 parts
Fan housing outer, Fanwheel
Fits SH 55, SH 85.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (10)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4229 701 0613 | Fan housing, outer | 1 |
| 1 | 4229 700 4103 | Fan housing, outer | 1 |
| 2 | 9074 478 4545 | Pan head self-tapping screw IS-P6x26.5 | 7 |
| 3 | 4229 704 7900 | Washer | 2 |
| 4 | 4229 768 0300 | Shredder blade | 1 |
| 5 | 4229 704 3400 | Fanwheel | 1 |
| 6 | 9211 260 1150 | Hexagon nut M8x1 l/h thread | 1 |
| 7 | 4229 706 8000 | Screen | 1 |
| 8 | 0000 998 0807 | Torsion spring | 1 |
| 9 | 4229 716 6700 | Star nut | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later fanwheel removal and SH shredder blade
The fanwheel nut loosens clockwise (left-hand thread); only SH 55/85 have the stated shredder-blade removal step.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- The unheaded right column on printed 34 / PDF35 precedes section 10.1 on printed 35 / PDF36: remove the spark plug, block the piston with locking strip 4221 893 5900, and remove the blower tube or elbow through the model-specific sections 10.4 and 10.6. Its placement beside fuel hoses 9.6.3 is a layout ambiguity; these fan-access steps are not added to hose replacement.
- For BG 55, 65, 85, take out the screws and lift away the outer fan housing. The separate BG 45 illustration is outside this TI-linked model scope. For SH 55, 85, unscrew the star nut, take out the screws and lift away the outer fan housing. No BG 46-specific access method is established here.
- Unscrew fanwheel nut (1) clockwise because it has a left-hand thread. On SH 55, 85, remove shredder blade (2); then remove washer (3), fanwheel (4) and the washer behind the fanwheel. Inspect all blades and replace the fanwheel if necessary. Install in reverse sequence; retain both washer positions rather than collapsing them into one washer.
- The star nut for SH housing access is not the left-hand fanwheel nut. Section 10.1 supplies no replacement part number, wear dimension, blade repair method or balancing procedure. Its illustrated SH blade stack does not establish a shredder blade on BG models or universal fanwheel interchange. Torque values must retain their joint/model restrictions from section 3.2; no generic fan-nut torque is inferred from this procedure.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later fanwheel removal and SH shredder blade.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later fanwheel removal and SH shredder blade, PDF pages 1, 3, 4, 35, 36, 37
Part numbers (1)
- 4221 893 5900 — Locking stripBlocking the piston for fanwheel service · January2005 component service setup only; not an installed part or universal substitute
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later protective screen and torsion spring
The all-except-BG45 screen uses retaining tabs and a torsion spring; the SH suction-tube opening step remains SH-only.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 10.2, printed 35 / PDF36, is headed all except BG 45. Within it the opening preparation is explicitly SH units only: remove the suction tube through 10.5, press down the retaining tab on the protective screen and swing it open. Do not transfer that suction-tube prerequisite to a BG blower.
- Use a screwdriver or similar tool to press down the retaining tabs (1) on the outer fan housing and lift away protective screen (2). Remove the torsion spring shown in the lower illustration; install in reverse sequence. The screen-opening tab and housing attachment tabs are separate illustrated locations. No spring preload turns, replacement number or screw torque is supplied for this clipped screen.
- Section 10.3 is BG 45 only: screws, right-hand guide engagement and checking the seal for damage and seating. It is reviewed as outside this TI29 model intersection, not a second installation method for BG 55/65/85 or SH 55/85. Do not transfer its seal or screw-retained construction to the 10.2 screen.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later protective screen and torsion spring.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later protective screen and torsion spring, PDF pages 1, 3, 4, 36, 37
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later component servicing tools and wrench restrictions
The 2005 table lists thirteen tool rows and two wrench alternatives; T-handle use on DG/P screws is removal-only.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 11, printed 37 / PDF38, is the component manual tool table, not a claim that these tools are installed machine parts. Applications are transcribed individually. No availability, present-day substitute, kit inclusion or physical interchange is established.
- Remark 1 on both torque wrenches requires a torque wrench for tightening DG or P screws. The 0.5 to 18 Nm and 6 to 80 Nm entries are wrench ranges, not joint torque settings. Remark 2 pairs 5910 890 0302 with 5910 890 0301; remark 3 pairs 5910 890 0312 with 5910 890 0311. The alternatives have optical/acoustic signals; do not swap their range assignments.
- Remark 4 restricts T-handle screwdriver Q-T27x150 5910 890 2400 to releasing/removing DG or P screws. Its general IS-screw application is not permission to tighten those screws by feel. The separate T27x125 socket row explicitly includes torque-wrench tightening.
- The vacuum-pump and tester applications name crankcase/carburetor tests, and the vacuum pump also names tank-vent testing. This inventory does not specify safe pressure, vacuum, hold time or acceptance limits; the separate source pressure-unit conflicts remain unresolved. The later table is not substituted for the August1999 powerhead tool list.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later component servicing tools and wrench restrictions.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later component servicing tools and wrench restrictions, PDF pages 1, 3, 4, 38
Part numbers (15)
- 4221 893 5900 — Locking stripBlocking crankshaft · January2005 component-manual service tool only; not installed fitment
- 0812 540 1112 — SocketInstalling/removing spline socket head screws with electric or pneumatic screwdrivers · January2005 component-manual service tool only; not installed fitment
- 0000 850 3501 — Vacuum pumpTesting crankcase/carburetor for leaks and testing tank vent · January2005 component-manual service tool only; not installed fitment
- 1106 850 2905 — Carburetor and crankcase testerTesting crankcase and carburetor for leaks · January2005 component-manual service tool only; not installed fitment
- 0000 855 9200 — NippleTesting carburetor for leaks · January2005 component-manual service tool only; not installed fitment
- 1110 141 8600 — Hose for leakage testTesting carburetor for leaks · January2005 component-manual service tool only; not installed fitment
- 5910 890 2420 — Screwdriver Q-SW 8 x 200Carburetor nuts · January2005 component-manual service tool only; not installed fitment
- 5910 890 8210 — Crimping toolAttaching connectors to electrical wires · January2005 component-manual service tool only; not installed fitment
- 5910 890 0301 — Torque wrench0.5 to 18 Nm range; DG/P tightening requires torque wrench; remarks1/2 · January2005 component-manual service tool only; not installed fitment
- 5910 890 0311 — Torque wrench6 to 80 Nm range; DG/P tightening requires torque wrench; remarks1/3 · January2005 component-manual service tool only; not installed fitment
- 0812 524 2104 — Socket T 27 x 125Installing/removing spline socket head screws with electric or pneumatic screwdrivers; torque-wrench tightening · January2005 component-manual service tool only; not installed fitment
- 5910 890 2400 — T-handle screwdriver Q-T27x150IS screws; DG/P screws releasing/removing only (remark4) · January2005 component-manual service tool only; not installed fitment
- 5910 893 8800 — HookRemoving pickup body · January2005 component-manual service tool only; not installed fitment
- 5910 890 0302 — Torque wrench with optical/acoustic signalAlternative to 5910 890 0301 (0.5 to 18 Nm range) · January2005 component-manual service tool only; not installed fitment
- 5910 890 0312 — Torque wrench with optical/acoustic signalAlternative to 5910 890 0311 (6 to 80 Nm range) · January2005 component-manual service tool only; not installed fitment
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later housing and fan joint torque restrictions
The 17.0 Nm fanwheel nut setting is SH-with-shredder-blade only; matching screw sizes do not make different housing torques interchangeable.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 3.2, printed 5–6 / PDF6–7: M8x1LH-06 fanwheel/crankshaft nut is 17.0 Nm specifically for SH with shredder blade. Within this TI intersection that means the stated SH 55/85 configuration, not a BG fanwheel setting. The left-hand designation is retained; general DG/P screw directions do not override this nut thread.
- P6x15/49 collar screw/inner blower housing is 4.0 Nm, SH 55/85 only (remark 2). IS-P6x26.5 outer/inner blower housings is 5.0 Nm. IS-P6x19 fan housing/inner blower housing and IS-DG5x20Z fan housing/spiral housing are each 6.0 Nm. These rows supply joint-specific values, not replacement part numbers or a model/year selector for housing versions.
- The already reviewed IS-DG5x24 inner blower housing/crankcase and inner blower housing/engine pan rows are each 8.0 Nm; separate IS-DG5x24 spiral housing/crankcase and spiral housing/engine pan rows are each 6.0 Nm. Identical thread size does not establish interchangeable torque or housing construction.
- Remaining table reconciliation: IS-DG5x60 muffler/cylinder 9.0 Nm; IS-DG5x24 catalytic muffler/cylinder 9.0 Nm; literal M14x7 stub/muffler 10.0 Nm only for the version with spark arresting screen in muffler. IS-DG5x24 spacer flange/cylinder is 6.0 Nm only with binding head (remark 1). M14x1.25 spark plug is 20.0 Nm. The unusual M14x7 notation is not silently corrected.
- IS-P6x19 handle/inner blower housing is 5.0 Nm for BG 85/SH 85 only (remark 3); IS-P6x19 handle molding/inner blower housing is 4.0 Nm for BG 65/85/SH 85 only (remark 4). The IS-P6x19 protective screen/outer blower housing row is 5.0 Nm for BG 45 only (remark 5), outside this TI intersection; it is not a clipped-screen setting for BG 55/65/85 or SH 55/85.
- DG/P screws form permanent threads in polymer/light metal. A torque wrench and specified torque are required. In an existing thread turn counterclockwise until the screw drops slightly, then clockwise to torque; do not cut a new thread. Maximum power-screwdriver speeds in polymer are Plastoform 600 rpm and DG 500 rpm. Do not mix screws with and without binding heads. These are screwdriver limits, not engine speeds or permission to replace a missing joint torque.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and separate handbook dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later housing and fan joint torque restrictions.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later housing and fan joint torque restrictions, PDF pages 1, 3, 4, 6, 7
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the SH 55, SH 85? Report a correction →