← BT 45

Stihl 4314 · Section H · 8 of 16 · 38 parts

Carburetor C1Q-S74E, C1Q-S74B

Fits BT 45.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222324252627282933031323334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (38)

PosPart numberDescriptionQty
1 4137 120 7100 Throttle shaft with lever 1
2 1123 122 3000 Spring 1
3 4128 121 8900 Pin 1
4 4137 121 8600 Washer 1
5 1120 122 9000 E-clip 1
6 4314 121 3301 Throttle shutter 1
7 1125 122 7403 Round head screw 1
8 1125 122 9001 E-clip 1
9 1129 121 4800 Pump diaphragm 1
10 1123 129 0905 Gasket 1
11 1123 121 0800 End cover 1
12 1120 122 7800 Oval head screw 1
13 4116 121 5100 Inlet needle 1
14 1128 122 3000 Spring 1
15 1125 121 5000 Inlet control lever 1
16 1120 121 9200 Spindle 1
17 1120 122 6600 Collar screw 1
18 4180 129 0902 Gasket 1
19 4314 121 4700 Metering diaphragm Fitment / change note → 1
20 4314 120 2200 Flange Fitment / change note → 1
21 4226 122 7100 Screw 4
22 4314 122 6700 High speed adjustment screw 1
23 4314 122 6801 Low speed adjustment screw 1
24 1123 121 7800 Strainer 1
25 4140 121 0800 End cover 1
26 4226 121 2700 Cap 1
27 4229 122 6200 Idle speed adjustment screw 1
28 1125 122 4200 Clamp 1
29 4229 121 2701 Cap 1
30 1130 121 5604 Fixed jet 0.45 1
31 not sold separately Pump piston not available as a separate item 1
32 not sold separately Sealing ring not available as a separate item 1
33 not sold separately Spring not available as a separate item 1
34 not sold separately Strainer not available as a separate item 1
Not numbered on the diagram — assemblies, kits and options
— 4314 120 0601 Carburetor C1Q-S74E Fitment / change note → 1
— not sold separately Carburetor C1Q-S74B no longer available from factory 1
— 4314 007 1053 Pump piston kit Fitment / change note → 1
— 4314 007 1052 Set of carburetor parts Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · BT 45

BT 45: C1Q-S74B to C1Q-S74D barbed carburetor

The complete carburetor changes number; connector geometry changes at both locations.

  • The cover identifies BT 45, series 4314. Previous C1Q-S74B 4314 120 0600, with smooth connectors on flange AND carburetor housing, is replaced by C1Q-S74D 4314 120 0601, with barbed connectors at both locations. Figure 421TI010 shows previous LEFT (carburetor 1, flange 4, connectors 2/3) and new RIGHT (carburetor 5, flange 8, connectors 6/7).
  • Previous carburetor is no longer factory available; new carburetor can also be used on older BT 45 machines. Summary rows 1/2 include flange, metering diaphragm, pump piston, sealing ring, spring and strainer (items 3,4,6–9); other unchanged parts are referred to the parts list, not an exhaustive carburetor bill of materials.
  • The retained exact-model IPL title includes C1Q-S74E and C1Q-S74B. That title is a navigation anchor, NOT proof this TI approves the later E variant or equates E with D. The page4 introduction is CONTINUOUS, not a production serial boundary.
  • Historical English-USA 2008 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 18/2008, p. 1 · TI 18/2008, p. 4 — BT 45: C1Q-S74B to C1Q-S74D barbed carburetor.

Part numbers (2)
  • 4314 120 0600 — C1Q-S74B carburetorPrevious; smooth connectors · BT 45; source restrictions apply
  • 4314 120 0601 — C1Q-S74D carburetorNew; barbed connectors · BT 45; source restrictions apply

Service note · BT 45

BT 45: barbed flange and retained other-model supply

The old flange remains available for other models.

  • Previous smooth-connector flange 4228 120 2200 is replaced on BT 45 by barbed flange 4314 120 2200. New flange can also be used on older BT 45 machines.
  • Previous flange remains factory available FOR OTHER MODELS (summary remark 3); this is not continuing approval to ignore the BT45 replacement or proof of interchange on unnamed models. Summary remark 4 points to the barbed-connector service notes.
  • Historical English-USA 2008 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 18/2008, p. 1 · TI 18/2008, p. 4 — BT 45: barbed flange and retained other-model supply.

Part numbers (2)
  • 4228 120 2200 — Smooth-connector flangePrevious; retained for other models · BT 45; source restrictions apply
  • 4314 120 2200 — Barbed flangeNew; older BT45 permitted · BT 45; source restrictions apply

Service note · BT 45

BT 45: new fuel hoses and OH 723 assembly fluid

Do not reuse removed hoses or lubricate them with fuel, oil or grease.

  • Install/remove hoses BY HAND WHENEVER POSSIBLE to avoid barbed-connector damage. Sharp-edged pliers, screwdrivers and similar tools must not be used; do not cut hoses open with a knife or similar implement.
  • Always replace disassembled fuel hoses with NEW hoses: removal may over-extend them. Install new hoses DRY or using Press Fluid OH 723, 0781 957 9000. OTHER PRESS FLUIDS ARE NOT PERMITTED and may damage hoses.
  • When using OH 723, apply it to hose ENDS AND CONNECTORS before installation. Its temporary lubricant film evaporates, allowing a tight fit. NEVER use FUEL, OIL OR GREASE: they do not evaporate as required and may let the hose slip off. No hose length or leak-test pressure is supplied in this TI.
  • Historical English-USA 2008 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 18/2008, p. 2 — BT 45: new fuel hoses and OH 723 assembly fluid.

Part numbers (1)
  • 0781 957 9000 — Press Fluid OH 723Only named permitted assembly fluid · BT 45; source restrictions apply

Service note · BT 45

BT 45: metering diaphragm and carburetor-parts set

The new set differs by its metering diaphragm; it is not the pump-piston kit.

  • Metering diaphragm 4229 121 4700 becomes 4314 121 4700. New diaphragm can be used on older BT45 machines; previous diaphragm remains available FOR OTHER MODELS.
  • Set of carburetor parts 4314 007 1051 becomes 4314 007 1052. The stated difference is new diaphragm 4314 121 4700. Previous set is no longer factory available; new set can also be used on older machines.
  • Summary item 5 includes diaphragm item 4; other components are as previously and referred to the parts list. Do not invent the set’s full contents, or confuse set 1052 with complete pump-piston kit 1053.
  • Historical English-USA 2008 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 18/2008, p. 2 · TI 18/2008, p. 4 — BT 45: metering diaphragm and carburetor-parts set.

Part numbers (4)
  • 4229 121 4700 — Metering diaphragmPrevious; retained for other models · BT 45; source restrictions apply
  • 4314 121 4700 — Metering diaphragmNew · BT 45; source restrictions apply
  • 4314 007 1051 — Set of carburetor partsPrevious · BT 45; source restrictions apply
  • 4314 007 1052 — Set of carburetor partsNew; includes new diaphragm · BT 45; source restrictions apply

Service note · BT 45

BT 45: complete pump-piston kit for both carburetors

Replace all four components together, including the unchanged-version strainer.

  • New pump-piston kit 4314 007 1053 is for BOTH previous C1Q-S74B 4314 120 0600 AND new C1Q-S74D 4314 120 0601, including older machines. Figure 253TI008 identifies NEW pump piston 1, sealing ring 2 and spring 3, plus PREVIOUS-VERSION strainer 4.
  • The kit is offered ONLY COMPLETE; new individual parts are not separately available. ALWAYS replace previous OR new versions of piston, sealing ring, spring AND strainer with the complete kit 1053 (summary remark 5). An unchanged strainer design is not permission to replace only three components.
  • Previous piston 4229 121 5800, sealing ring 4140 122 3600, spring 4229 122 3001 and strainer 1120 121 7801 remain available FOR OTHER MODELS. The summary’s -*- cells are no separate new order numbers, not zero or unchanged numbered parts.
  • Historical English-USA 2008 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 18/2008, p. 3 · TI 18/2008, p. 4 — BT 45: complete pump-piston kit for both carburetors.

Part numbers (7)
  • 4314 007 1053 — Pump piston kitComplete four-component replacement · BT 45; source restrictions apply
  • 4314 120 0600 — C1Q-S74B carburetorKit applicable · BT 45; source restrictions apply
  • 4314 120 0601 — C1Q-S74D carburetorKit applicable · BT 45; source restrictions apply
  • 4229 121 5800 — Previous pump pistonOther-model supply retained · BT 45; source restrictions apply
  • 4140 122 3600 — Previous sealing ringOther-model supply retained · BT 45; source restrictions apply
  • 4229 122 3001 — Previous springOther-model supply retained · BT 45; source restrictions apply
  • 1120 121 7801 — StrainerPrevious version retained in kit · BT 45; source restrictions apply

Wrong number or missing part for the BT 45? Report a correction →