Stihl 1111 · Section J · 9 of 10 · 50 parts
Cast arm, V-belt pulley
Fits TS 50.
Parts (50)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4205 701 0200 | Cast arm | 1 |
| 2 | 4205 703 8900 | Plate | 1 |
| 3 | 9062 319 1260 NLA | Countersunk screw M6x12 | 2 |
| 4 | 4205 704 1000 | V-belt pulley | 1 |
| 5 | 4205 162 8100 | Corrugated spring | 1 |
| 6 | 9456 621 3100 | Circlip 28x1.2 | 2 |
| 7 | 9503 003 5190 | Grooved ball bearing 6001-2RS | 2 |
| 8 | 4205 703 9000 | Pin | 1 |
| 9 | 9455 621 1130 | Circlip 12x1 | 1 |
| 10 | 9291 021 0220 | Washer 13 | 1 |
| 11 | 9211 260 1460 | Hexagon nut M12x1.5 | 1 |
| 12 | 4205 701 0100 | Bearing | 1 |
| 13 | 9007 319 1900 | Hexagon head screw M8x40 | 3 |
| 14 | 9308 021 0180 | Washer 8.4 | 2 |
| 15 | 9503 003 5190 | Grooved ball bearing 6001-2RS | 2 |
| 16 | 0000 961 1210 | Ring | 1 |
| 17 | 4201 700 2800 | Shaft | 1 |
| 18 | 4223 036 8600 | Woodruff key | 1 |
| 19 | 9490 000 7890 | Narrow V-belt 9.5x925 | 1 |
| 20 | 0000 958 1212 | Washer | 1 |
| 21 | 4201 704 1000 | V-belt pulley | 1 |
| 22 | 9291 021 0200 | Washer 10.5 | 1 |
| 23 | 9211 260 1350 | Hexagon nut M10x1 l/h thread | 1 |
| 24 | 9172 068 1950 | T-head bolt | 1 |
| 26 | 9291 021 0180 | Washer 8.4 | 1 |
| 27 | 9322 630 0180 | Spring washer 8 | 1 |
| 28 | 0000 997 0620 | Compression spring | 1 |
| 29 | 1109 660 0500 | Tensioning nut | 1 |
| 30 | 4201 700 8101 | Guard | 1 |
| 31 | 4201 706 8800 | Rubber bushing | 1 |
| 32 | 9455 621 4330 | Circlip 40x1.75 | 1 |
| 33 | 4201 708 3002 | Washer | 1 |
| 34 | 4201 708 3012 | Washer | 1 |
| 35 | 9008 319 2350 | Hexagon head screw M10x18 | 1 |
| 36 | 0000 955 0901 | Collar nut M10 | 2 |
| 37 | 9380 620 2020 | Roll pin 4x6 | 1 |
| 38 | not sold separately | Cutting wheels | |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4205 708 3200 | Segment | 1 |
| — | not sold separately | for stone: | |
| — | 0835 020 2003 | Cutting wheel Ø 300x3.5 mm | 1 |
| — | 0835 020 3004 NLA | Cutting wheel Ø 300x6 mm | 1 |
| — | 0835 022 1007 NLA | Cutting wheel Ø 350x4 mm | 1 |
| — | not sold separately | for steel: | |
| — | 0835 010 2003 | Cutting wheel Ø 300x3.5 mm | 1 |
| — | 0835 012 1007 NLA | Cutting wheel Ø 350x4 mm | 1 |
| — | not sold separately | for asphalt: | |
| — | 0835 030 1003 | Cutting wheel Ø 300x3.5 mm | 1 |
| — | not sold separately | Diamond cutting wheel not illustratedoption | |
| — | 0835 099 2021 | Diamond cutting wheel for stone: | 1 |
| — | 0835 080 1002 NLA | Diamond cutting wheel Ø 300x2.8 mm | 1 |
2012 service parts catalogue. Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Wrong number or missing part for the TS 50? Report a correction →