← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section K · 10 of 16 · 33 parts

Carburetor WT-426

Fits 024.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314141515161617181922021222324252627282933031456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (33)

PosPart numberDescriptionQty
1 4116 121 5100 Inlet needle 1
2 1114 122 3005 Spring 1
3 1113 121 5000 Inlet control lever 1
4 1113 121 9200 Spindle 1
5 1114 122 7400 Round head screw 1
6 4117 122 9402 Plug 1
7 1121 121 5400 Valve jet 0.48 Fitment / change note → 1
8 1120 129 0900 Gasket 1
9 1113 121 4705 Metering diaphragm 1
10 1121 121 0810 End cover 1
11 1121 122 7101 Screw 4
12 1110 122 7400 Round head screw 1
13 1121 121 3301 Throttle shutter 1
14 4130 122 3600 Sealing ring Fitment / change note → 2
15 4130 121 8601 Washer Fitment / change note → 2
16 1115 122 3002 Spring 2
17 1121 122 6700 High speed adjustment screw Fitment / change note → 1
18 1121 122 6802 Low speed adjustment screw Fitment / change note → 1
19 1113 122 3205 Torsion spring 1
20 1121 120 7105 Throttle shaft with lever 1
21 1117 122 9000 E-clip 1
22 1114 121 7800 Strainer 1
23 1121 121 4801 Pump diaphragm 1
24 1120 129 0905 Gasket 1
25 1121 121 0805 End cover 1
26 1122 121 7700 Clamp 1
27 1121 122 6205 Idle speed adjustment screw 1
28 1114 122 7100 Screw 1
29 1121 121 5601 Fixed jet 0.46 option 1
30 1113 121 0800 End cover 1
31 1106 122 7400 Round head screw 4
Not numbered on the diagram — assemblies, kits and options
— 1121 120 0611 Carburetor WT-426 1
— 1121 007 1062 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 024 / 026

024/026 WT394 to WT426: unchanged number, revised metering

1121 120 0650 alone cannot distinguish the two carburetor versions.

X 36 348 620 — Printed production introduction for TI18/1997 tank-housing and carburetor changes only; not the undated spark-plug boot seal deletion.

  • New carburetor versions enter production from X 36 348 620. The type changes from WT 394 to WT 426, but table items 1 and 2 BOTH USE 1121 120 0650. Only the MODIFIED carburetor version is available from the factory (remark 1); the number alone does not identify its internal configuration.
  • The new valve jet has a calibrated 0.48 mm DIAMETER orifice (semi-fixed jet). APPROXIMATELY 75% of required fuel flows through it IRRESPECTIVE OF H-SCREW POSITION. This is a fuel-flow statement, not 75% screw opening or a tuning setting. TI18 attributes more accurate tuning and less sensitivity to incorrect adjustment; no RPM, screw-turn setting or universal performance guarantee is specified.
  • New H and L screws are sealed with O-RING AND WASHER. Drawing 133TI030 identifies valve jet (1), O-ring (2), washer (3), and depicts the seal/washer components at both screws; these are NOT summary-table item numbers. The table lists valve jet 1120 121 5405 to 1121 121 5400, H screw 1118 122 6700 to 1121 122 6700, L screw 1120 122 6805 to 1121 122 6802, plus O-ring 4130 122 3600 and washer 4130 121 8601.
  • The summary says above includes followed by items 3–7; all other parts as before. Original jet, H screw and L screw remain available for the ORIGINAL CARBURETOR AND OTHER MODELS (remark 2); this is not permission to mix them with the new seal arrangement or proof of reciprocal retrofit.
  • Configuration difference retained: TI31/1995 page 3 prescribes LOCTITE 221 for the earlier compensator-cover carburetor screws, whereas TI18 describes NEW SCREWS SEALED BY O-RING AND WASHER. TI18 does not explicitly instruct adding adhesive, or globally cancel the old procedure. Do not combine the two sealing methods merely because the carburetor part number is unchanged. No retrofit kit or complete rebuild sequence is specified.
  • Historical TI18/1997 evidence for 024 and 026 only, not MS240/MS260 or other successors. Model-sheet links aid discovery, not universal variant fitment. Factory supply statements describe the bulletin date, not current stock. No reciprocal interchange or physical verification inferred. No hardware operation was performed.

Source: TI 18/1997, p. 1 · TI 18/1997, p. 4 — 024/026 WT394 to WT426: unchanged number, revised metering.

Referenced bulletin evidence: TI 31/1995, p. 3 — Earlier carburetor screw-sealing instruction; not transferred to WT426.

Part numbers (9)
  • 1121 120 0650 — WT394 original / WT426 new carburetorSame part number; only modified version supplied · 024/026; 024/026 WT394 to WT426: unchanged number, revised metering; configuration restrictions in note
  • 1120 121 5405 — Original valve jet, table 3Retained for original carburetor and other models · 024/026; 024/026 WT394 to WT426: unchanged number, revised metering; configuration restrictions in note
  • 1121 121 5400 — New semi-fixed valve jet, table 30.48 mm calibrated orifice · 024/026; 024/026 WT394 to WT426: unchanged number, revised metering; configuration restrictions in note
  • 1118 122 6700 — Original H screw, table 4Retained for original carburetor and other models · 024/026; 024/026 WT394 to WT426: unchanged number, revised metering; configuration restrictions in note
  • 1121 122 6700 — New H screw, table 4New sealing arrangement · 024/026; 024/026 WT394 to WT426: unchanged number, revised metering; configuration restrictions in note
  • 1120 122 6805 — Original L screw, table 5Retained for original carburetor and other models · 024/026; 024/026 WT394 to WT426: unchanged number, revised metering; configuration restrictions in note
  • 1121 122 6802 — New L screw, table 5New sealing arrangement · 024/026; 024/026 WT394 to WT426: unchanged number, revised metering; configuration restrictions in note
  • 4130 122 3600 — O-ring, table 6 / drawing 2New H/L screw seal · 024/026; 024/026 WT394 to WT426: unchanged number, revised metering; configuration restrictions in note
  • 4130 121 8601 — Washer, table 7 / drawing 3New H/L screw sealing arrangement · 024/026; 024/026 WT394 to WT426: unchanged number, revised metering; configuration restrictions in note

Wrong number or missing part for the 024? Report a correction →