← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section J · 9 of 16 · 31 parts

Air filter, Throttle control

Fits 024.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112121313141516171819220212223242526272829330304567889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (31)

PosPart numberDescriptionQty
1 1121 120 0611 Carburetor WT-426 1
2 1121 120 0604 Carburetor WT-110 1
3 9645 945 7485 O-ring 7x2.5 Fitment / change note → 1
4 1121 123 7501 Grommet 1
5 1118 123 7500 Grommet → replaced by 1121 123 7500 TI 39/1997 1
6 1121 122 7000 Grommet 1
7 9210 260 0700 Hexagon nut M5 2
8 1121 120 1617 NLA Air filter option 1
8 1121 120 1618 Air filter, fleece 1
9 1121 120 2900 Choke shutter 1
10 1121 124 3000 Torsion spring 1
11 1124 141 8300 Slotted nut 1
12 1121 120 1610 Air filter, wire mesh 1
13 1121 120 1625 Air filter, fleece Fitment / change note → option 1
14 1121 121 7001 Baffle 1
15 1121 141 8300 Slotted nut 2
16 0000 997 5505 Tension spring 1
17 1121 121 2900 Choke shutter 1
18 9395 825 1090 Split pin 2x10 1
19 1117 182 0805 Lockout lever 1
20 1121 182 1501 Throttle rod 1
21 1118 182 1006 Throttle trigger 1
22 1117 182 4500 Torsion spring 1
23 9371 470 2640 Cylindrical pin 5x24 1
24 1125 182 0900 Switch shaft Fitment / change note → → replaced by 1125 182 0901 TI 30/1995 1
25 1125 442 1601 Contact spring 1
26 1121 790 1701 Handlebar 1
27 9074 478 4475 Pan head self-tapping screw IS-P6x21.5 2
28 9074 478 4675 Pan head self-tapping screw IS-P6x32.5 2
29 0000 791 2009 Handle hose Ø 19 mm x 5 m / 3/4x197'' 1
30 9074 478 4435 Pan head self-tapping screw IS-P6x19 4

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 024 / 026

024 / 026: replacement carburetor needs the correct end cover

New carburetor 1121 120 0650 includes the original end cover for non-compensator 026 and 024 use; that does not authorize the new filter system on 024.

  • The new air filter, carburetor with compensator connector and carburetor box cover may be installed only as a complete assembly, and only in 026 from X 30 976 775. This earlier retrofit threshold is not the production introduction X 32 252 039. The lower tank vent gives clearance for the wider filter; TI 06/1995 is retained separately, not a missing source.
  • The connector on the metering end cover projects into the inner filter half, connecting clean-side pressure to the outside of the metering diaphragm. The source says this avoids over-richening as the filter dirties and removes the need to readjust H for increasing filter contamination; it is not a new tuning value or a universal performance guarantee.
  • For 026 without compensator and for 024, use the included original end cover 1113 121 0800 with replacement carburetor 1121 120 0650. This is the explicit 024 exception; the full compensator-filter retrofit remains 026-only.
  • Page 5 carburetor item 7 includes items 8–10: new end cover 1121 121 0810, O-ring 9645 945 7485 and screw 1121 122 7101. All other carburetor parts remain as before. Original carburetor 1121 120 0606 is no longer available from the factory; original end cover and screw remain spares. These are 1995 supply statements.
  • For repair of a carburetor with compensator cover, thoroughly clean H and L adjusting screws and recoat with fresh LOCTITE 221. Leave the first two to three thread turns uncoated; adhesive must not enter the carburetor. Correctly sealed screws tend to be slightly difficult to turn. No adjustment setting or torque is supplied here.
  • The source does not identify a WT model for 1121 120 0650. Do not alias it to later WT-426, WT-403B, WT-493A, WT-427 or WT-590 catalog rows.

Source: TI 31/1995, p. 2 · TI 31/1995, p. 3 · TI 31/1995, p. 4 · TI 31/1995, p. 5 — Sections 1.1, 1.3–1.5: compensator connection, replacement cover, adjusting-screw service and rows 7–10.

Part numbers (7)
  • 1121 120 0606 — CarburetorOriginal · 024 and 026 only with the end-cover/configuration conditions above
  • 1121 120 0650 — Replacement carburetorNew; original cover included for non-compensator use · 024 and 026 only with the end-cover/configuration conditions above
  • 1113 121 0800 — Metering end coverOriginal; conditional companion · 024 and 026 only with the end-cover/configuration conditions above
  • 1121 121 0810 — Compensator metering end coverNew · 024 and 026 only with the end-cover/configuration conditions above
  • 9645 945 7485 — O-ringNew · 024 and 026 only with the end-cover/configuration conditions above
  • 1106 122 7400 — Round head screwOriginal · 024 and 026 only with the end-cover/configuration conditions above
  • 1121 122 7101 — Round head screwNew · 024 and 026 only with the end-cover/configuration conditions above

Historical fitment · 024 / 026

024 / 026: switch-shaft standardization

The standardized shaft has a numeric introduction boundary; the interim shaft is retained only for 024.

X 33 339 218 — Standardized switch shaft introduced from this machine number; earlier small interim batch has no specified interval.

  • Original 1121 182 0900 is replaced by 1125 182 0901 from X 33 339 218. Original version is no longer supplied from the factory in this dated source.
  • A small number of machines before this change used 1125 182 0900. That interim shaft can still be used for model 024; the source does not grant the same continued use for 026 or identify an interim serial interval.
  • Page5 marks 1125 182 0901 as a universal replacement for all versions in this bulletin context. The shared series does not extend this claim to later MS260 machines.

Source: TI 12/1996, p. 1 · TI 12/1996, p. 5 — Section1 and section2.5 item10.

Part numbers (3)

Historical fitment · 024 / 026

024 / 026: contact spring with connector tag

The connector-tag spring replaces the old spring for all 024 and 026 versions.

  • Contact spring 1121 442 1600 changes to 1125 442 1600 with introduction of carburetor heating. The thermostatic switch flag connector attaches to the new spring connector tag shown by the arrow.
  • The new spring is explicitly a universal replacement for all versions of models 024 and 026. This replacement rule does not make every 024 a carburetor-heated model and does not extend to later MS260.
  • No numeric production cutoff for the spring is printed; neither tank nor switch-shaft serial is borrowed.

Source: TI 12/1996, p. 2 · TI 12/1996, p. 5 — Section2.2 and section2.5 item11.

Part numbers (2)
  • 1121 442 1600 — Contact springOriginal · 024 / 026
  • 1125 442 1600 — Contact spring with connector tagUniversal replacement · All 024 / 026 versions

Service note · 024 / 036

036 switch shaft: shorter tang; original remains usable on 024

0900 becomes 0901 with the short-circuit-wire tang shortened by 2 mm.

  • In connection with the modified 036 air filter, switch shaft 1125 182 0900 is replaced by 1125 182 0901. The tang for the SHORT CIRCUIT WIRE is shortened by 2 mm (0.08 inch). This is a part revision, not an instruction to cut an old shaft.
  • Original 1125 182 0900 CAN STILL BE USED FOR MODEL 024. The 024 exception concerns the original shaft only; it does not extend the new 036 air-filter system or its serial thresholds to 024. Later 036 K key31 lists 0901 and 024 J retains 0900.
  • No separate shaft introduction serial or field-modification dimensions are supplied. Earlier TI28 housing-shaft statements remain separate; this TI establishes this specific 0900-to 0901 change without resolving the older tank-vent serial conflict.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 5 — Section 1.2.2 switch shaft paragraph.

Part numbers (2)
  • 1125 182 0900 — Original switch shaft036 original; continued 024 use · 024 / 036; Section 1.2.2 switch shaft paragraph
  • 1125 182 0901 — Shorter-tang switch shaft036 modified-air-filter version · 036 with modified air filter; not a new 024 fitment claim

Service note · 024

024: fleece filter under unchanged numbers

Fleece replaces flocked wire cloth; old stock, cleaning direction and replacement limits remain distinct.

  • TI38/1996 replaces flocked wire cloth with fleece under UNCHANGED replacement-part numbers. Introduction is IN PROGRESS, without a serial cutoff. Remark 1 says the unmodified version is supplied until existing stocks are exhausted. A number alone therefore does not identify the material of an old-stock filter; this is a historical supply statement, not a current stock guarantee.
  • The 024 row is 1121 120 1625 with remark 1 ONLY. The adjacent 026 row is 1121 120 1612 with remarks 1 and 2. Those are distinct rows, not a shared filter number or permission to fit the 026 compensator conversion to 024. Both numbers were visually transcribed because the retained extracted text is corrupt.
  • The source calls fleece especially suitable for dry and dusty conditions. Its rougher surface may look heavily contaminated when only lightly loaded; appearance alone does not establish loading. Clean DAILY OR when there is a noticeable loss of power during cutting. The observation about appearance does not cancel that interval.
  • If possible, carefully blow out at LOW PRESSURE from the CLEAN AIR SIDE. For stubborn dirt or caked fleece, wash in a clean, NON-FLAMMABLE solution, for example warm soapy water. DO NOT CLEAN WITH A BRUSH: it forces dirt into the fleece. No pressure value, drying time or alternate solvent is specified.
  • The source attributes improved filtering efficiency to the material structure, not a measured result here. Some trapped particles cannot be cleaned out; replace the filter when cleaning intervals become too short for practical use, or when noticeable cutting-power loss persists after thorough cleaning.
  • Historical guidance for these named models and filter configurations only; no successor-model fitment, universal interchange or material identity inferred from a shared part number. No hardware operation was performed.

Source: TI 38/1996, p. 1 · TI 38/1996, p. 2 — Complete filter-material and servicing guidance; exact model summary rows and remarks.

Part numbers (1)
  • 1121 120 1625 — Air filterunchanged material-revision number · 024; TI38/1996 row and configuration conditions

Wrong number or missing part for the 024? Report a correction →