Stihl 1121 · Section M · 12 of 16 · 32 parts
Chain sprocket cover, Shroud
Fits 024.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1125 640 1701 | Chain sprocket cover Fitment / change note → → replaced by 1122 640 1702, 1128 640 1706 TI 36/2000 | 1 |
| 2 | 1121 648 6610 | Bumper strip | 2 |
| 3 | 1125 656 1501 | Guard | 1 |
| 4 | 1125 656 1500 | Guard | 1 |
| 5 | 1125 656 1505 | Guard option | 1 |
| 6 | 9099 021 1760 | Self-tapping screw 2.9x9.5 | 1 |
| 7 | 1121 656 1500 | Guard | 1 |
| 8 | 9039 488 0340 | Self-tapping screw M3x8 | 1 |
| 9 | 0000 955 0801 | Hexagon nut M8 | 2 |
| 10 | 1110 664 0501 | Bumper spike | 1 |
| 11 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 2 |
| 12 | 9214 320 0700 | Lock nut M5 | 1 |
| 13 | 0000 953 6605 | Collar screw M8 | 2 |
| 14 | 1121 664 2400 | Collar screw | 1 |
| 15 | 1121 080 1609 | Shroud | 1 |
| 16 | 1119 084 8300 | Reflector foil | 1 |
| 17 | 1122 084 7100 | Cap | 1 |
| 18 | 1121 080 1600 | Shroud | 1 |
| 19 | 1121 080 1602 | Shroud | 1 |
| 20 | 1121 084 1601 | Cover | 1 |
| 22 | 1121 967 1511 | Model plate 024 Fitment / change note → | 1 |
| 23 | 1121 967 1508 | Model plate 024 Fitment / change note → | 1 |
| 24 | 0000 974 1000 | Round head rivet 3x6 Fitment / change note → | 1 |
| 25 | 1121 084 7000 | Slotted nut | 1 |
| 26 | 1121 084 6901 | Insulator | 1 |
| 27 | 1121 084 7100 | Cap | 1 |
| 28 | 1121 080 3000 | Air guide plate option | 1 |
| 29 | not sold separately | Cover plate optionnot available as a separate item | 1 |
| 30 | 1121 084 7300 | Hose option | 1 |
| 31 | 9022 341 0980 | Spline screw IS-M5x16 option | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1121 007 1031 | Set Bumper spike option | 1 |
| — | 1121 007 1007 | Air guide plate option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 024 / 026 / 034 / 036
024 / 026 / 034 / 036: sprung side plate requires the revised cover
Side plate 1122 664 1000 changes to 1122 664 1001; new plate installation requires the matching new cover. The general cover row changes 1125 640 1700 to 1125 640 1701.
- When fitting the revised sprung-tab side plate during a repair, the new-version chain sprocket cover must also be fitted. The tabs hold the guide bar during chain assembly; this is not approval to use the new plate with the original cover.
- Original side plates remain available for original covers/older machines in this bulletin. Original covers are supplied only while existing stocks last; these are historical availability statements.
- The source identifies new covers by integrally cast numbers 1122 648 0401 and 1125 648 0404. These are identification marks, not the 640-group cover ordering numbers or established ordering aliases. The prose does not explicitly pair each cast number to a summary row.
- The illustrated installation removes the M4x8 pan-head screw and old plate, pushes the new plate over the bar studs, then seats it using a combination wrench and one short blow with a plastic mallet.
- For the FIRST installation of a new side plate, the source says to mount the guide bar and cover and tighten the M8 nuts to about 15–20 Nm (11–15 lbf.ft). This historical seating step is not a universal torque specification for later models or normal recurring bar adjustment.
- Illustrated removal fits an M8 nut to the rear bar stud, twists the combination-wrench screwdriver end about 45° counterclockwise under the plate, raises the wrench end about 10–15 mm (1/2 in), then removes the nut and plate. Preserve the illustrated orientation; no hardware operation is verified here.
- Pan-head screw 9041 216 0630 is omitted in the revised arrangement, not globally discontinued: the summary says it remains a spare for other models.
- Introduction is in progress, dated May 17, 1994, without a numeric serial cutoff. The seven explicitly named models do not establish applicability to successors, 046, or unlisted variants. Prior-TI references are bibliography, not inherited compatibility.
Source: TI 12/1994, p. 1 · TI 12/1994, p. 2 · TI 12/1994, p. 3 · TI 12/1994, p. 4 — Cover/side-plate service note, assembly/disassembly and model-qualified summary.
Part numbers (7)
- 1122 664 1000 — Original side platePrevious version · Retained for original cover
- 1122 664 1001 — Sprung-tab side plateNew version · Requires new-version cover
- 1125 640 1700 — Chain sprocket coverPrevious general cover · Historical while-stocks-last availability
- 1125 640 1701 — Chain sprocket coverNew general cover · Named models in general summary row
- 9041 216 0630 — Pan-head screw M4x8Removed from new arrangement · Still a spare for other models
- 1122 648 0401 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
- 1125 648 0404 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
Historical fitment · 024
024: plastic nameplate requires revised shroud
The clip-in plastic plate cannot replace the riveted aluminium plate on the original shroud.
- The riveted aluminium nameplate changes to a clip-in plastic plate retained by two lugs. Revised shrouds have two countersunk mounting holes. Plastic nameplates cannot be fitted in the original shroud because those holes are not countersunk.
- Aluminium nameplates and two round head rivets 0000 974 1000, size3x6, remain available for older machines in this dated source. Rivets are deleted for the new clip-in arrangement; that is not a blanket spare-part deletion.
- Introduction is in progress with no numeric production boundary. No shroud ordering number, countersinking modification procedure, current-stock promise or cross-model plate interchange is established.
Source: TI 12/1996, p. 6 — Section4 full service note, summary and remark.
Part numbers (3)
- 1121 967 1508 — Aluminium nameplate 024Retained replacement · Original shroud
- 1121 967 1511 — Plastic nameplate 024New clip-in version · Revised countersunk shroud only
- 0000 974 1000 — Round head rivet3x6, twoRetained for original plate · Older machines
Wrong number or missing part for the 024? Report a correction →