← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section L · 11 of 17 · 35 parts

Air filter, Throttle control

Fits 026.

Parts diagrams →

Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11101112131414141415161718192220212324252627282933031323334353645667789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (35)

PosPart numberDescriptionQty
1 1121 120 1617 NLA Air filter Fitment / change note → 1
2 1121 120 1618 Air filter, fleece Fitment / change note → 1
3 1124 141 8300 Slotted nut Fitment / change note → 2
4 1121 124 3000 Torsion spring Fitment / change note → 1
5 1121 120 2900 Choke shutter Fitment / change note → 1
6 1121 120 1611 Air filter, wire mesh Fitment / change note → 1
7 1121 120 1612 Air filter, fleece Fitment / change note → 1
8 1121 121 7001 Baffle Fitment / change note → 1
9 1121 141 8300 Slotted nut Fitment / change note → 2
10 0000 997 5505 Tension spring Fitment / change note → 1
11 1121 121 2900 Choke shutter Fitment / change note → 1
12 9395 825 1090 Split pin 2x10 Fitment / change note → 1
13 1121 120 0611 Carburetor WT-426 1
14 9645 945 7485 O-ring 7x2.5 Fitment / change note → 1
15 1121 120 0610 Carburetor WT-403B 1
16 1121 120 0613 Carburetor WT-493A 1
17 1121 120 0612 Carburetor WT-427 1
18 1121 120 0616 Carburetor WT-590 1
19 1128 434 5101 Heating element 1
20 1118 431 6600 NLA Terminal pin no longer available from factory 1
21 1125 121 9900 Heater plate 1
23 1118 123 7500 Grommet Fitment / change note → → replaced by 1121 123 7500 TI 39/1997 1
24 1121 123 7502 Grommet 1
25 1121 123 7500 Grommet Fitment / change note → 1
26 1121 123 7504 Grommet 1
27 1121 122 7000 Grommet 1
28 9210 260 0700 Hexagon nut M5 2
29 1121 182 1501 Throttle rod 1
30 1118 182 1006 Throttle trigger 1
31 1117 182 4500 Torsion spring 1
32 9371 470 2640 Cylindrical pin 5x24 1
33 1117 182 0805 Lockout lever 1
34 1125 182 0901 Switch shaft Fitment / change note → 1
35 1125 442 1601 Contact spring 1
36 1125 442 1600 Contact spring Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 026

026: compensator filter requires the complete system

The wider 1995 filter is a conditional complete-system retrofit, not a standalone swap or a 024 conversion.

X 32 252 039 — 026 production introduction of the new filter system and decompression valve; not the earlier complete-system retrofit threshold.

  • The new air filter, carburetor with compensator connector and carburetor box cover may be installed only as a complete assembly, and only in 026 from X 30 976 775. This earlier retrofit threshold is not the production introduction X 32 252 039. The lower tank vent gives clearance for the wider filter; TI 06/1995 is retained separately, not a missing source.
  • Larger filter area, two-ply polyamide instead of wire mesh, molded-in baffle, redesigned choke shutter, inner compensator connection and cover-retaining lugs identify the new design. The felt option replaces the flocked option. Longer filter life, improved retention and reduced maintenance are vendor claims, not measured performance.
  • Page 4 compares the old and new exploded assemblies. Page 5 item 1 includes items 2–6 as applicable: the old separate baffle and split pin disappear in the new design; do not carry deleted parts into it. Old separate parts remain spares under remark 1, whereas the new baffle is integral.
  • The original filters remain available according to the 1995 bulletin. This is not a current stock statement. Later catalog presence on 024 does not broaden this TI’s 026-only conversion permission.

Source: TI 31/1995, p. 1 · TI 31/1995, p. 3 · TI 31/1995, p. 4 · TI 31/1995, p. 5 — Sections 1, 1.1, 1.3–1.5: filter construction, retrofit limit and full filter rows.

Part numbers (12)
  • 1121 120 1611 — Air filterOriginal · 026; complete-system conditions apply
  • 1121 120 1612 — Flocked air filterOriginal · 026; complete-system conditions apply
  • 1121 120 1617 — Air filterNew · 026; complete-system conditions apply
  • 1121 120 1618 — Felt air filterNew option · 026; complete-system conditions apply
  • 1121 121 7001 — Separate baffleOriginal; deleted in new design · 026; complete-system conditions apply
  • 1121 141 8300 — Slotted nutOriginal · 026; complete-system conditions apply
  • 1124 141 8300 — Slotted nutNew · 026; complete-system conditions apply
  • 0000 997 5505 — SpringOriginal · 026; complete-system conditions apply
  • 1121 124 3000 — SpringNew · 026; complete-system conditions apply
  • 1121 121 2900 — Choke shutterOriginal · 026; complete-system conditions apply
  • 1121 121 2905 — Choke shutterNew · 026; complete-system conditions apply
  • 9395 825 1090 — Split pin 2x10Original; deleted in new design · 026; complete-system conditions apply

Conditional replacement · 026

026: new cover and summer/winter air path

The revised cover draws air at the bottom and moves its screen cover for winter operation; the preheating kit changes with the filter system.

X 32 252 039 — 026 production introduction of the new filter system and decompression valve; not the earlier complete-system retrofit threshold.

  • The new air filter, carburetor with compensator connector and carburetor box cover may be installed only as a complete assembly, and only in 026 from X 30 976 775. This earlier retrofit threshold is not the production introduction X 32 252 039. The lower tank vent gives clearance for the wider filter; TI 06/1995 is retained separately, not a missing source.
  • Combustion air now enters between the cover and tank housing at the bottom, not the old top gap. The 90° twist-lock lever secures the cover to the filter. An integral plastic screen replaces the wire-mesh prefilter.
  • For summer operation, cover 1121 141 2900 seals the screen. For winter operation, remove it and fit it in the slot at the bottom of the carburetor box cover as arrowed on page 2; warm cylinder air then mixes with cold air. This TI supplies no temperature threshold.
  • Page 4 and table item 11 include items 12–19 as applicable. New lever 1130 141 2300 replaces the old twist lock; old prefilter, two self-tapping screws, helical spring and detent are deleted from the new assembly, not required carryovers. Remark 1 retains the old cover and old components as spares.
  • Preheating kit 1121 007 1027 changes to 1121 007 1044, with carburetor box cover 1121 140 1906 changing to 1121 140 1907; all other kit parts remain as before. The new kit is for 026 with the new filter system. Old kit/cover availability is historical. No 024 or MS260 retrofit inferred.

Source: TI 31/1995, p. 1 · TI 31/1995, p. 2 · TI 31/1995, p. 3 · TI 31/1995, p. 4 · TI 31/1995, p. 5 — Sections 1.1, 1.3–1.5: cover illustration, all cover rows and preheating kit.

Part numbers (14)
  • 1121 140 1902 — Carburetor box coverOriginal · 026; complete-system conditions apply
  • 1121 140 1904 — Carburetor box coverNew · 026; complete-system conditions apply
  • 1121 124 0811 — Wire-mesh prefilterOriginal; deleted in new design · 026; complete-system conditions apply
  • 1121 141 2900 — Summer/winter screen coverNew · 026; complete-system conditions apply
  • 9099 021 0160 — Self-tapping screw B2.2x6.5Original; deleted in new design · 026; complete-system conditions apply
  • 1121 141 2300 — Twist lockOriginal; deleted in new design · 026; complete-system conditions apply
  • 1130 141 2300 — LeverNew · 026; complete-system conditions apply
  • 0000 997 1335 — Helical springOriginal; deleted in new design · 026; complete-system conditions apply
  • 1121 141 2100 — DetentOriginal; deleted in new design · 026; complete-system conditions apply
  • 9099 021 2790 — Self-tapping screw B3.9x16Original; deleted in new design · 026; complete-system conditions apply
  • 1121 007 1027 — Intake air preheating kitOriginal · 026; complete-system conditions apply
  • 1121 007 1044 — Intake air preheating kitNew · 026; complete-system conditions apply
  • 1121 140 1906 — Preheating-kit carburetor box coverOriginal · 026; complete-system conditions apply
  • 1121 140 1907 — Preheating-kit carburetor box coverNew · 026; complete-system conditions apply

Conditional replacement · 024 / 026

024 / 026: replacement carburetor needs the correct end cover

New carburetor 1121 120 0650 includes the original end cover for non-compensator 026 and 024 use; that does not authorize the new filter system on 024.

  • The new air filter, carburetor with compensator connector and carburetor box cover may be installed only as a complete assembly, and only in 026 from X 30 976 775. This earlier retrofit threshold is not the production introduction X 32 252 039. The lower tank vent gives clearance for the wider filter; TI 06/1995 is retained separately, not a missing source.
  • The connector on the metering end cover projects into the inner filter half, connecting clean-side pressure to the outside of the metering diaphragm. The source says this avoids over-richening as the filter dirties and removes the need to readjust H for increasing filter contamination; it is not a new tuning value or a universal performance guarantee.
  • For 026 without compensator and for 024, use the included original end cover 1113 121 0800 with replacement carburetor 1121 120 0650. This is the explicit 024 exception; the full compensator-filter retrofit remains 026-only.
  • Page 5 carburetor item 7 includes items 8–10: new end cover 1121 121 0810, O-ring 9645 945 7485 and screw 1121 122 7101. All other carburetor parts remain as before. Original carburetor 1121 120 0606 is no longer available from the factory; original end cover and screw remain spares. These are 1995 supply statements.
  • For repair of a carburetor with compensator cover, thoroughly clean H and L adjusting screws and recoat with fresh LOCTITE 221. Leave the first two to three thread turns uncoated; adhesive must not enter the carburetor. Correctly sealed screws tend to be slightly difficult to turn. No adjustment setting or torque is supplied here.
  • The source does not identify a WT model for 1121 120 0650. Do not alias it to later WT-426, WT-403B, WT-493A, WT-427 or WT-590 catalog rows.

Source: TI 31/1995, p. 2 · TI 31/1995, p. 3 · TI 31/1995, p. 4 · TI 31/1995, p. 5 — Sections 1.1, 1.3–1.5: compensator connection, replacement cover, adjusting-screw service and rows 7–10.

Part numbers (7)
  • 1121 120 0606 — CarburetorOriginal · 024 and 026 only with the end-cover/configuration conditions above
  • 1121 120 0650 — Replacement carburetorNew; original cover included for non-compensator use · 024 and 026 only with the end-cover/configuration conditions above
  • 1113 121 0800 — Metering end coverOriginal; conditional companion · 024 and 026 only with the end-cover/configuration conditions above
  • 1121 121 0810 — Compensator metering end coverNew · 024 and 026 only with the end-cover/configuration conditions above
  • 9645 945 7485 — O-ringNew · 024 and 026 only with the end-cover/configuration conditions above
  • 1106 122 7400 — Round head screwOriginal · 024 and 026 only with the end-cover/configuration conditions above
  • 1121 122 7101 — Round head screwNew · 024 and 026 only with the end-cover/configuration conditions above

IPL correction · 026

026: repair-kit number differs between prose and table

Page 3 prints 1121 900 9004; page 5 prints 1121 900 5004 for the new ElastoStart repair kit. Neither number is silently corrected.

  • Both numbers are legible in the original scans, not merely an OCR mismatch. Page 3 calls the new repair kit 1121 900 9004; page 5 calls it 1121 900 5004 and names the old kit 1121 900 5002. This is an unresolved source conflict, not an established alias or a verified ordering recommendation.
  • The page 5 repair-kit (ElastoStart) row includes item 1, the air filter. Do not replace that explicit inclusion with a guessed starter-only inventory or infer every kit component. Page 3 restricts the new repair kit to 026 with the new filter system; the old table entry remains a spare under remark 1.
  • No correction source has been established. The conflicting assertion is retained and dispositioned, not resolved; no invented source gap is used to skip other locally actionable content.

Source: TI 31/1995, p. 3 · TI 31/1995, p. 5 — Section 1.4 final paragraph versus section 1.5 special-accessory table.

Part numbers (3)
  • 1121 900 9004 — New repair kit, prose spellingConflicting source number · 026 with new filter system for the disputed new kit; no verified alias
  • 1121 900 5004 — New repair kit (ElastoStart), table spellingConflicting source number · 026 with new filter system for the disputed new kit; no verified alias
  • 1121 900 5002 — Repair kit (ElastoStart)Original table number · 026 with new filter system for the disputed new kit; no verified alias

Historical fitment · 024 / 026

024 / 026: switch-shaft standardization

The standardized shaft has a numeric introduction boundary; the interim shaft is retained only for 024.

X 33 339 218 — Standardized switch shaft introduced from this machine number; earlier small interim batch has no specified interval.

  • Original 1121 182 0900 is replaced by 1125 182 0901 from X 33 339 218. Original version is no longer supplied from the factory in this dated source.
  • A small number of machines before this change used 1125 182 0900. That interim shaft can still be used for model 024; the source does not grant the same continued use for 026 or identify an interim serial interval.
  • Page5 marks 1125 182 0901 as a universal replacement for all versions in this bulletin context. The shared series does not extend this claim to later MS260 machines.

Source: TI 12/1996, p. 1 · TI 12/1996, p. 5 — Section1 and section2.5 item10.

Part numbers (3)

Historical fitment · 024 / 026

024 / 026: contact spring with connector tag

The connector-tag spring replaces the old spring for all 024 and 026 versions.

  • Contact spring 1121 442 1600 changes to 1125 442 1600 with introduction of carburetor heating. The thermostatic switch flag connector attaches to the new spring connector tag shown by the arrow.
  • The new spring is explicitly a universal replacement for all versions of models 024 and 026. This replacement rule does not make every 024 a carburetor-heated model and does not extend to later MS260.
  • No numeric production cutoff for the spring is printed; neither tank nor switch-shaft serial is borrowed.

Source: TI 12/1996, p. 2 · TI 12/1996, p. 5 — Section2.2 and section2.5 item11.

Part numbers (2)
  • 1121 442 1600 — Contact springOriginal · 024 / 026
  • 1125 442 1600 — Contact spring with connector tagUniversal replacement · All 024 / 026 versions

Conditional replacement · 026 / MS 260

026 / MS 260: two-part choke assembly, unchanged filter numbers

The new freely pivoting shutter is an assembly; its shaft and shutter are not separate spares.

  • Choke assembly 1121 120 2900 replaces 1121 121 2905. It consists of shaft and freely pivoting shutter, allowing closer seating against the carburetor opening in the choke/starting position. The shaft and shutter are not available separately; do not invent separate item36/37 numbers.
  • Mesh-screen filter 1121 120 1617 and fleece filter 1121 120 1618 keep their part numbers and each include the choke assembly. Unmodified filter versions are supplied until factory stocks are exhausted; old choke assemblies are likewise stocks-only. An unchanged filter number alone cannot identify which choke construction is present.
  • Section9 records separate MS 260 parts lists in the 03.2001 microfiche/CD-ROM issues. This is an edition-availability statement, not proof that the current 01-2012 navigation sheets reproduce that historical edition. All other parts are stated unchanged.
  • Shared IPL sheets do not extend these changes to unnamed variants. Introduction is in progress; the TI gives no numerical serial cutoff. Availability is the historical 2001 factory statement, not current stock. Later catalog numbers do not replace the historical evidence or prove unrestricted interchangeability.

Source: TI 43/2001, p. 6 · TI 43/2001, p. 8 — Sections8–9, exploded air-filter drawing and summary rows33–37/remarks2–4.

Part numbers (4)
  • 1121 121 2905 — Choke shutter assemblyPrevious; stocks only · Only the named model/configuration; see conditions
  • 1121 120 2900 — Two-part choke assemblyNew · Only the named model/configuration; see conditions
  • 1121 120 1617 — Mesh-screen air filterUnchanged number; revised contents · Only the named model/configuration; see conditions
  • 1121 120 1618 — Fleece air filterUnchanged number; revised contents · Only the named model/configuration; see conditions

Service note · 026

026: fleece filter under unchanged numbers

Fleece replaces flocked wire cloth; old stock, cleaning direction and replacement limits remain distinct.

  • TI38/1996 replaces flocked wire cloth with fleece under UNCHANGED replacement-part numbers. Introduction is IN PROGRESS, without a serial cutoff. Remark 1 says the unmodified version is supplied until existing stocks are exhausted. A number alone therefore does not identify the material of an old-stock filter; this is a historical supply statement, not a current stock guarantee.
  • The 026 row prints 1121 120 1612 and remarks 1 and 2; remark 2 says SEE TI31.95. Retained TI31/1995 distinguishes the older filter from the wider compensator system. TI38 is a SAME-NUMBER MATERIAL change, not permission for a standalone new-system conversion.
  • The already-reviewed TI31/1995 restricts the new air filter, compensator carburetor and carburetor box cover to a COMPLETE ASSEMBLY on 026 from X 30 976 775, with the lower tank vent providing clearance. Production introduction X 32 252 039 is a different threshold; neither serial is the fleece introduction cutoff. The 024 row does not inherit this conversion.
  • The source calls fleece especially suitable for dry and dusty conditions. Its rougher surface may look heavily contaminated when only lightly loaded; appearance alone does not establish loading. Clean DAILY OR when there is a noticeable loss of power during cutting. The observation about appearance does not cancel that interval.
  • If possible, carefully blow out at LOW PRESSURE from the CLEAN AIR SIDE. For stubborn dirt or caked fleece, wash in a clean, NON-FLAMMABLE solution, for example warm soapy water. DO NOT CLEAN WITH A BRUSH: it forces dirt into the fleece. No pressure value, drying time or alternate solvent is specified.
  • The source attributes improved filtering efficiency to the material structure, not a measured result here. Some trapped particles cannot be cleaned out; replace the filter when cleaning intervals become too short for practical use, or when noticeable cutting-power loss persists after thorough cleaning.
  • Historical guidance for these named models and filter configurations only; no successor-model fitment, universal interchange or material identity inferred from a shared part number. No hardware operation was performed.

Source: TI 38/1996, p. 1 · TI 38/1996, p. 2 — Complete filter-material and servicing guidance; exact model summary rows and remarks.

Referenced bulletin evidence: TI 31/1995, p. 1 · TI 31/1995, p. 3 — Previously reviewed new-system production and complete-system retrofit conditions; not a fleece cutoff.

Part numbers (1)
  • 1121 120 1612 — Air filterunchanged older-system material-revision number · 026; TI38/1996 row and configuration conditions

Service note · 026 / 026 PRO

026: gray single-hole grommet removes H-screw access

1121 123 7500 replaces 1118 123 7500; original remains available for older machines.

2 36 988 352 — Introduction from this machine number for TI39/1997 modifications; no inferred model-wide interchange range.

  • Section 2 replaces the original grommet with a GRAY grommet having ONLY ONE HOLE, FOR L. Drawing 133TI034 KN shows two holes on original version 1 and one on new version 2; these version labels are not terminal IDs or summary positions. No extra LA opening is stated here.
  • Summary item 15 carries remark 1: ORIGINAL VERSION REMAINS AVAILABLE FOR OLDER MACHINES. The new single-hole grommet is not an unconditional fit for every H-adjustable 026 carburetor.
  • The exact 026 air-filter/throttle-control sheet retains both numbers and is the assembly association here. Shared 024 or MS 260 usage does not transfer the TI39 change or serial to those models.
  • Modification is introduced FROM machine number 2 36 988 352, printed identically in section 1 and the summary. This is the historical TI39/1997 configuration, not current stock, a universal retrofit or verified physical interchange. No hardware operation was performed.

Source: TI 39/1997, p. 1 · TI 39/1997, p. 2 — Section2, full comparison drawing133TI034 KN and summary item15/remark1.

Part numbers (2)
  • 1118 123 7500 — Original two-hole grommet; drawing 1 / summary 15Original remains available for older machines · Exact 026 / 026 PRO TI39/1997 configuration as qualified in this note
  • 1121 123 7500 — Gray single-hole L grommet; drawing 2 / summary 15Replacement for fixed-jet configuration · Exact 026 / 026 PRO TI39/1997 configuration as qualified in this note

Wrong number or missing part for the 026? Report a correction →