← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section Q · 16 of 17 · 28 parts

Heating

Fits 026.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011111213141516171819220212224252627282934567778889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 1121 440 2201 NLA Ground wire 1
2 0751 030 8962 Terminal socket A 8-1 no longer available from factory 1
3 0751 030 8950 NLA Terminal socket A 4-1 no longer available from factory 1
4 1110 430 0202 Stop switch 1
5 1110 432 9200 Grommet 1
6 1128 434 5000 NLA Heating element 1
7 1118 431 6600 NLA Terminal pin Fitment / change note → no longer available from factory 1
8 1118 431 6700 NLA Terminal socket no longer available from factory 1
9 1121 442 0406 NLA Insulating hose 40 mm / 1.6'' 1
10 1121 791 9000 NLA Clamp 1
11 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' Fitment / change note → 3
12 1121 440 3000 Wiring harness Fitment / change note → 1
13 1123 442 0400 Shrink-on tube 1
14 1119 442 7000 Contact sleeve no longer available from factory 2
15 not sold separately Terminal socket not available as a separate item 1
16 0751 030 8957 Terminal socket 4.8-1/0.8 no longer available from factory 1
17 0751 030 8969 Terminal socket A5-1.5 no longer available from factory 1
18 0000 989 0507 Grommet Fitment / change note → 1
19 1121 405 8001 Insulating hose 90 mm / 3.5'' Fitment / change note → 1
20 1125 434 5000 NLA Heating element 1
21 1121 430 3202 Circuit board 1
22 1110 442 7000 NLA Contact sleeve no longer available from factory 1
24 1121 440 2203 Ground wire 1
25 0751 030 8402 Terminal socket 2.8-1/0.5 no longer available from factory 1
26 0751 030 8969 Terminal socket A5-1.5 no longer available from factory 1
27 4112 432 9202 Grommet 1
28 0751 030 8466 Terminal socket housing no longer available from factory 1
29 1121 791 1300 Sealing flap 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 026

026 VH: WT 395 carburetor and heater components

The automatic Arctic Pro system uses a specific WT 395 assembly; cut-out temperature is not a switch-on setting.

  • 026 VH Arctic Pro is introduced as a future version with automatic carburetor heating to avoid low-temperature icing; no numeric system-introduction cutoff is supplied. This is a source description, not a tested anti-icing result.
  • WT 395 (VH) carburetor 1121 120 0609 includes end cover 1121 121 0810 with compensator connection, O-ring A7 9645 945 7485, retainer 1121 122 4605, thermostatic switch 1125 430 0500 and four round head screws 1121 122 7101 (items13–17). These are original WT 395 contents, not later carburetor internals.
  • The thermostatic switch is secured to the end cover by the retainer and has a 120 mm (about 4 3/4 inch) yellow-green wire with flag connector. Cut-out temperature is +7 to +13 °C (printed 45 to 55 °F); no switch-on threshold, hysteresis or resistance value is supplied.
  • Heating element 1128 434 5101 and heating plate 1125 121 9900 fit between carburetor and air filter; they are separate items4–5, not included by the carburetor inclusion row. Flywheel (VH) 1121 400 1207 and generator 1118 400 4000 are separate items2–3.
  • Only tank housing, switch shaft and contact spring carry the universal-replacement remark in the page5 table. It does not make the VH flywheel, generator, heater or WT 395 universal for all versions. No blanket heating retrofit kit is specified.

Source: TI 12/1996, p. 2 · TI 12/1996, p. 5 — Sections2,2.1 and full section2.5 component inclusion.

Part numbers (10)
  • 1121 120 0609 — Item12: WT 395 (VH) carburetor026 VH listed component · Includes items13–17
  • 1121 121 0810 — Item13: end cover026 VH listed component · Included in WT 395
  • 9645 945 7485 — Item14: O-ring A7026 VH listed component · Included in WT 395
  • 1121 122 4605 — Item15: retainer026 VH listed component · Included in WT 395
  • 1125 430 0500 — Item16: thermostatic switch026 VH listed component · Included in WT 395
  • 1121 122 7101 — Item17: round head screw, four026 VH listed component · Included in WT 395
  • 1128 434 5101 — Item4: heating element026 VH listed component · Separate from carburetor
  • 1125 121 9900 — Item5: heating plate026 VH listed component · Separate from carburetor
  • 1121 400 1207 — Item2: flywheel (VH)026 VH listed component · 026 VH
  • 1118 400 4000 — Item3: generator026 VH listed component · 026 VH; service wire conversion applies

Historical fitment · 026

026 VH: harness insulation and generator lead

The replacement harness and generator require source-specific preparation, routing and insulated connectors.

  • Harness 1121 440 3000 contains ground, short circuit and generator-connecting wires. At the fan housing it passes through insulating tube 1121 405 8001, diameter 9 mm. Grommet 0000 989 0507 serves the carburetor-box entry.
  • Tube 1121 442 0402 insulates both the generator-to-connecting-wire and connecting-wire-to-heater joints. The summary lists two 35 mm lengths. It is not interchangeable by inference with the separate diameter9mm fan-housing tube.
  • Before fitting the replacement harness, the source says cut off unnecessary wire (1) just behind the crimped joint in drawing133TI026 KN. The wire is identified by the original illustration, not by an invented color or electrical pinout; this is not an instruction to cut arbitrary harness wires.
  • The standard generator lead on carburetor-heated machines is 102 mm (4 inch), with a connector pin that mates to the harness terminal socket behind the ignition module. For replacement generator 1118 400 4000, shorten the lead to that length and attach terminal pin 1118 431 6600. No crimp-tool/die specification or strip length is provided here.
  • Push retainer (1) into the crankcase recess, place connection (2) as drawing133TI017 KN, completely cover connectors with the tube, then install the ignition module. Route the wire in crankcase slot (3), clear of the flywheel. Do not infer an ignition-module air gap, fastener torque or retainer ordering number.

Source: TI 12/1996, p. 3 · TI 12/1996, p. 5 — Sections2.3,2.4.1 and section2.5 items3,6–9.

Part numbers (6)
  • 1121 440 3000 — Wiring harnessReplacement preparation required · 026 VH
  • 1121 405 8001 — Insulating tube, diameter9mmFan-housing protection · 026 VH
  • 0000 989 0507 — GrommetCarburetor-box entry · 026 VH
  • 1121 442 0402 — Hose, two 35mm lengthsConnector insulation · Both heater circuit joints
  • 1118 400 4000 — GeneratorReplacement lead modification · 026 VH
  • 1118 431 6600 — Terminal pinReplacement-generator companion · 102mm generator lead

Historical fitment · 026

026 VH: carburetor-box wiring and heater orientation

The original routing drawings distinguish ground, short circuit and heater connections and show TOP 1121 orientation.

  • Properly seat the harness grommet in the cutout at the top of the carburetor box; all three harness wires pass through it. Loop the generator/heater connection wire behind the ribs as drawing133TI023 KN; the insulating tube must completely cover the connectors.
  • Push the yellow-green ground-wire connector sleeve into the contact-spring loop. Push the short-circuit-wire connector sleeve into the switch-shaft seat. Route both wires behind the illustrated ribs (133TI024 KN). These are distinct destinations, not an interchangeable pair.
  • Push carburetor over the collar screws to the manifold flange without pinching wires. Move Master Control lever fully down to cold start. Fit the thermostatic-switch flag connector to the contact-spring tag; this tag is distinct from the loop receiving the ground wire.
  • Slip the heating element over the collar screws onto the carburetor, then fit the heating plate with TOP 1121 oriented as drawing133TI025 KN. The printed ordering number is 1125 121 9900; TOP 1121 is a marking, not a substitute ordering number.
  • These are the printed routing and assembly steps for 026 VH, not electrical diagnostic results, a universal retrofit or an instruction to energize hardware. The original drawing supplies orientation; no unprinted torque or wiring pinout is inferred.

Source: TI 12/1996, p. 4 · TI 12/1996, p. 5 — Section2.4.2 complete sequence and drawings133TI023/024/025 KN.

Part numbers (5)
  • 1121 440 3000 — Wiring harnessRouting subject · 026 VH
  • 1125 442 1600 — Contact springSeparate loop and connector tag · Ground and thermostat destinations
  • 1125 182 0901 — Switch shaftShort-circuit connector seat · 026 VH installation
  • 1128 434 5101 — Heating elementBefore heating plate · 026 VH
  • 1125 121 9900 — Heating plate marked TOP 1121Orientation-sensitive companion · 026 VH

Wrong number or missing part for the 026? Report a correction →