← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section B · 2 of 17 · 35 parts

Cylinder, Muffler

Fits MS 260, MS 260 C.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

This drawing carries 2 bore sizes — Ø 44 mm (also listed for the 026), Ø 44.7 mm (this machine only). Not interchangeable — measure your cylinder before ordering.

Position —

Go to table row → Where else is this used →
111010111112121313141415151616171718181919222020212123232424242424242525252525252626262626262727272728282929333030313132323333445566778899
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (35)

PosPart numberDescriptionQty
1 1121 020 1217 Cylinder with piston Ø 44.7 mm 1
2 1121 030 2003 Piston Ø 44.7 mm 1
3 1121 034 3002 Piston ring Ø 44.7x1.2 mm 2
4 1121 034 1505 Piston pin 10x6x30 1
5 9463 650 1000 Snap ring 10 2
6 0000 953 0818 Stud M5 2
7 1122 025 2200 Plug 1
8 1121 020 1203 Cylinder with piston Ø 44 mm Fitment / change note → 1
9 1121 030 2001 Piston Ø 44 mm 1
10 1121 034 3010 Piston ring Ø 44x1.2 mm 2
11 9512 003 2252 Needle cage 10x13x12.5 1
12 1118 029 2306 Cylinder gasket 0.5 mm 1
13 1121 029 2305 Cylinder gasket 1 mm 1
14 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 4
15 1128 020 9400 Decompression valve 1
16 1122 084 1405 Cover 1
17 1121 084 7100 Cap 1
18 1110 400 7005 Spark plug Bosch WSR 6 F 1
18 0000 400 7000 Spark plug NGK BPMR7A 1
19 1121 141 6500 Spacer plate 1
20 1121 141 3200 Cooling plate 1
21 1118 149 0600 Muffler gasket 1
23 1121 145 0802 Exhaust casing 1
24 9022 341 0980 Spline screw IS-M5x16 2
25 9022 341 0980 Spline screw IS-M5x16 2
26 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 2
27 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 2
28 1121 140 0606 Muffler 1
29 1121 140 0803 Exhaust casing 1
30 1118 141 9005 Screen 1
31 9099 021 0810 Self-tapping screw 4.2x9.5 1
32 1121 140 0605 Muffler 1
33 1121 145 0805 Exhaust casing 1
Not numbered on the diagram — assemblies, kits and options
— 1121 007 1042 Mounting kit catalytic converter option 1
— 1121 007 1050 Set of gaskets option 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 026 / MS 260

026 / MS 260: ignition-lead routing, harness and 44 mm cylinder

Routing changes involve the crankcase, shroud and cylinder; the second illustrated harness is not assigned a variant.

  • The ignition lead is carried in an insulating tube within the crankcase cable channel. A retainer near the annular-buffer mounting holds it in position. The shroud wall between carburetor box and cylinder has a molded guide; three cylinder fins were shortened to accommodate it. This describes the revised manufactured geometry, not an instruction to grind an old cylinder.
  • Short-circuit and ground wires are enclosed in shrink tube and routed as a harness to the carburetor box in an insulating tube. The yellow/green ground wire is secured by the lower ignition-module mounting screw.
  • The summary defines harness 1121 440 3002 as including cable lug 0751 030 8969 (A5-1.5, unchanged), contact sleeve 1110 442 7000 replacing 1119 442 7000, terminal socket 0751 030 8957 (4.8-1/0.8, unchanged), and insulating tube. The previous contact sleeve and 90 mm tube 1121 405 8001 remain available for older machines, but the new tube is not supplied separately and has no independent part number in this table.
  • The diagram additionally labels harness 1121 440 3003, but the TI does not assign its model/variant or list it in the summary. It is retained as an unassigned illustrated reference, not approved as a substitute for 1121 440 3002 or attributed to a heated variant.
  • For the explicitly named 026 and MS 260, the 44 mm cylinder with piston changes from 1121 020 1209 to 1121 020 1203. The previous version is supplied only while factory stocks last. The coordinated routing geometry does not establish universal component interchange.
  • Shared IPL sheets do not extend these changes to unnamed variants. Introduction is in progress; the TI gives no numerical serial cutoff. Availability is the historical 2001 factory statement, not current stock. Later catalog numbers do not replace the historical evidence or prove unrestricted interchangeability.

Source: TI 43/2001, p. 2 · TI 43/2001, p. 4 · TI 43/2001, p. 5 · TI 43/2001, p. 7 · TI 43/2001, p. 8 — Section7 routing and both harness drawings; summary rows28–32,38/remarks1–3.

Part numbers (9)
  • 1121 440 3002 — Wiring harnessSummary assembly including items29–32 · Only the named model/configuration; see conditions
  • 1121 440 3003 — Illustrated wiring harnessUnassigned diagram reference; no variant fitment established · No model/variant assigned by TI43
  • 0751 030 8969 — Cable lug A5-1.5Unchanged · Only the named model/configuration; see conditions
  • 1119 442 7000 — Contact sleevePrevious; retained · Only the named model/configuration; see conditions
  • 1110 442 7000 — Contact sleeveNew · Only the named model/configuration; see conditions
  • 0751 030 8957 — Terminal socket 4.8-1/0.8Unchanged · Only the named model/configuration; see conditions
  • 1121 405 8001 — Insulating tube 90 mmPrevious; retained · Only the named model/configuration; see conditions
  • 1121 020 1209 — 44 mm cylinder with pistonPrevious; stocks only · Only the named model/configuration; see conditions
  • 1121 020 1203 — 44 mm cylinder with pistonNew · Only the named model/configuration; see conditions

Wrong number or missing part for the MS 260, MS 260 C? Report a correction →