Stihl 1121 · Section O · 14 of 17 · 41 parts
Carburetor WT-427, WT-581, WT-590 1 62 154 675, 2 62 187 361 (07.2004)
Fits MS 260, MS 260 C.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (41)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4124 122 3600 | Sealing ring | 1 |
| 2 | 4130 121 8601 | Washer | 2 |
| 3 | 1115 122 3002 | Spring | 1 |
| 4 | 1121 122 6802 | Low speed adjustment screw | 1 |
| 5 | 4130 122 3600 | Sealing ring | 1 |
| 6 | 1115 122 3002 | Spring | 1 |
| 7 | 1121 122 6700 | High speed adjustment screw | 1 |
| 8 | not sold separately | Sealing ring not available as a separate item | 2 |
| 9 | 1121 122 6804 | Low speed adjustment screw | 1 |
| 10 | 1121 122 6702 | High speed adjustment screw | 1 |
| 11 | 4203 121 2700 | Cap Fitment / change note → | 2 |
| 12 | 1121 121 5400 | Valve jet 0.48 | 1 |
| 13 | 4116 121 5100 | Inlet needle | 1 |
| 14 | 1114 122 3005 | Spring | 1 |
| 15 | 1113 121 5000 | Inlet control lever | 1 |
| 16 | 1113 121 9200 | Spindle | 1 |
| 17 | 1114 122 7400 | Round head screw | 1 |
| 18 | 4117 122 9402 | Plug | 1 |
| 19 | 1120 129 0900 | Gasket | 1 |
| 20 | 1113 121 4705 | Metering diaphragm | 1 |
| 21 | 1121 121 0810 | End cover | 1 |
| 22 | 1125 430 0500 | Switch | 1 |
| 23 | 1121 122 4605 | Support | 1 |
| 24 | 1121 122 7101 | Screw | 4 |
| 26 | 1121 121 4801 | Pump diaphragm | 1 |
| 27 | 1120 129 0905 | Gasket | 1 |
| 28 | 1121 121 0805 | End cover | 1 |
| 29 | 1122 121 7700 | Clamp | 1 |
| 30 | 1121 122 6205 | Idle speed adjustment screw | 1 |
| 31 | 1114 122 7100 | Screw | 1 |
| 32 | 1121 121 3301 | Throttle shutter | 1 |
| 33 | 1110 122 7400 | Round head screw | 1 |
| 34 | 1113 122 3205 | Torsion spring | 1 |
| 35 | 1121 120 7105 | Throttle shaft with lever | 1 |
| 36 | 1117 122 9000 | E-clip | 1 |
| 37 | 1121 121 5601 | Fixed jet 0.46 | 1 |
| 37 | 1121 121 5601 | Fixed jet 0.46 option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1121 120 0612 | Carburetor WT-427 | 1 |
| — | 1121 120 0616 | Carburetor WT-590 | 1 |
| — | 1121 120 0615 | Carburetor WT-581 | 1 |
| — | 1121 007 1062 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · MS 260
MS 260: revised limiter cap keeps the same number
Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
Later reviewed guidance: MS 260: square-bit driver for fitted limiter caps
- Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
- The new cap has no upper detent, adds an alignment mark and moves the lug from perpendicular to the screw slot into line with it.
- These models appear on the bulletin cover but NOT in the marked-segment subset on pages 2–4. Do not infer marked-segment alignment from cover inclusion; the slot, groove and visible-lug checks remain distinct from the marks-only instruction.
- The marked-segment drawing and its dimensions must not be assigned to these models solely from the shared limiter-cap number.
- H and L removal have separate alignment instructions. Puller 5910 890 4500 has a left-hand engagement thread; this note is not a complete carburetor removal or calibration procedure.
- Removed limiter caps must not be reused because removal damages them. Replace caps after screw replacement or carburetor cleaning; no permanent cap-removal modification is implied.
- Applies only to the named models with limiter cap 4203 121 2700. A shared catalog sheet is not approval for its other models or C/L variants. The sheet may contain uncapped versions; verify the actual carburetor configuration.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 21/2005, p. 1 · TI 21/2005, p. 2 · TI 21/2005, p. 3 · TI 21/2005, p. 4 — Sections 1–5: named-model cap revision; cover list distinguished from marked-segment subset.
Part numbers (2)
- 4203 121 2700 — Limiter capUnchanged number, revised geometry · Named models using 4203 121 2700; single-use after removal
- 5910 890 4500 — Limiter-cap pullerService tool · Left-hand engagement; separate H/L alignment
Conditional replacement · MS 260
MS 260: square-bit driver for fitted limiter caps
Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
- Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
- Conditional on limiter cap 4203 121 2700 actually being fitted, not every carburetor or every model/variant on the shared catalog sheet. Model association comes from TI 21/2005 and the catalog cap row; TI 50/2006 specifies the tool by cap configuration.
- The without-cap basic-setting illustration starts with adjusting screws closed to their seats. It does not supply a turn count or extend the illustrated H/L arrangement to every carburetor on this sheet.
- The source distinguishes initial engagement at the first detent from final fully-home seating after the series-specific basic setting. Do not treat the first detent as the completed installation.
- Required idle/high-speed settings depend on the exact series; this bulletin supplies no universal screw-turn or RPM setting. Later series-specific service guidance still governs.
- Caps removed to service an adjusting screw or clean the carburetor must not be reused. TI 21/2005 supplies the removal dependency; this is not authorization for permanent limiter removal.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 50/2006, p. 3 · TI 50/2006, p. 4 · TI 50/2006, p. 5 — Sections 3–3.4 and summary: capped-carburetor service tool and seating stages.
Part numbers (2)
- 5910 890 2304 — Square-bit carburetor screwdriverService tool · Carburetors using 4203 121 2700 fitted caps
- 4203 121 2700 — Limiter capExact tool configuration · New caps; final seating after series-specific basic setting
Wrong number or missing part for the MS 260, MS 260 C? Report a correction →