← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section M · 12 of 17 · 42 parts

Carburetor WTE-1A, WTE-2A, WTE-4A, WTE-11

Fits MS 260, MS 260 C.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220222324252627282933031323334353637456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (42)

PosPart numberDescriptionQty
1 4116 121 5100 Inlet needle 1
2 4116 122 3000 Spring 1
3 1121 121 5000 Inlet control lever 1
4 1113 121 9200 Spindle 1
5 1121 122 7103 Round head screw 1
6 1121 122 7102 Round head screw 1
7 1121 121 3302 Throttle shutter 1
8 1121 122 6806 Low speed adjustment screw 1
9 1121 122 6703 High speed adjustment screw 1
10 4203 121 2700 Cap Fitment / change note → 1
11 not sold separately Plug no longer available from factory 1
12 not sold separately Valve jet no longer available from factory 1
13 1121 121 5604 Fixed jet 0.48 1
14 1120 129 0900 Gasket 1
15 1121 121 4700 Metering diaphragm 1
16 1121 121 0810 End cover 1
17 1121 122 7101 Screw 4
18 4124 122 3600 Sealing ring 1
19 1111 121 8605 Washer 1
20 1115 122 3002 Spring 1
22 1121 120 7105 Throttle shaft with lever 1
23 1117 122 9000 E-clip 1
24 1114 121 7800 Strainer 1
25 1121 121 4801 Pump diaphragm 1
26 1120 129 0905 Gasket 1
27 1121 121 0801 End cover 1
28 1122 121 7700 Clamp 1
29 1121 122 6201 Idle speed adjustment screw 1
30 1114 122 7100 Screw 1
31 1125 430 0500 Switch 1
32 1121 122 4605 Support 1
33 1123 121 5631 Fixed jet 0.46 option 1
33 1123 121 5631 Fixed jet 0.46 1
34 1129 121 5600 Fixed jet 0.50 1
35 1121 121 3303 Throttle shutter 1
36 1121 122 6808 Low speed adjustment screw 1
37 1121 122 6704 High speed adjustment screw 1
Not numbered on the diagram — assemblies, kits and options
— 1121 120 0602 Carburetor WTE-1A 1
— 1121 120 0619 Carburetor WTE-4A 1
— 1121 120 0614 Carburetor WTE-2A 1
— 1121 120 0621 Carburetor WTE-11 1
— 1121 007 1063 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · MS 260

MS 260: revised limiter cap keeps the same number

Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.

Later reviewed guidance: MS 260: square-bit driver for fitted limiter caps

  • Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
  • The new cap has no upper detent, adds an alignment mark and moves the lug from perpendicular to the screw slot into line with it.
  • These models appear on the bulletin cover but NOT in the marked-segment subset on pages 2–4. Do not infer marked-segment alignment from cover inclusion; the slot, groove and visible-lug checks remain distinct from the marks-only instruction.
  • The marked-segment drawing and its dimensions must not be assigned to these models solely from the shared limiter-cap number.
  • H and L removal have separate alignment instructions. Puller 5910 890 4500 has a left-hand engagement thread; this note is not a complete carburetor removal or calibration procedure.
  • Removed limiter caps must not be reused because removal damages them. Replace caps after screw replacement or carburetor cleaning; no permanent cap-removal modification is implied.
  • Applies only to the named models with limiter cap 4203 121 2700. A shared catalog sheet is not approval for its other models or C/L variants. The sheet may contain uncapped versions; verify the actual carburetor configuration.
  • Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.

Source: TI 21/2005, p. 1 · TI 21/2005, p. 2 · TI 21/2005, p. 3 · TI 21/2005, p. 4 — Sections 1–5: named-model cap revision; cover list distinguished from marked-segment subset.

Part numbers (2)
  • 4203 121 2700 — Limiter capUnchanged number, revised geometry · Named models using 4203 121 2700; single-use after removal
  • 5910 890 4500 — Limiter-cap pullerService tool · Left-hand engagement; separate H/L alignment

Conditional replacement · MS 260

MS 260: square-bit driver for fitted limiter caps

Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.

  • Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
  • Conditional on limiter cap 4203 121 2700 actually being fitted, not every carburetor or every model/variant on the shared catalog sheet. Model association comes from TI 21/2005 and the catalog cap row; TI 50/2006 specifies the tool by cap configuration.
  • The without-cap basic-setting illustration starts with adjusting screws closed to their seats. It does not supply a turn count or extend the illustrated H/L arrangement to every carburetor on this sheet.
  • The source distinguishes initial engagement at the first detent from final fully-home seating after the series-specific basic setting. Do not treat the first detent as the completed installation.
  • Required idle/high-speed settings depend on the exact series; this bulletin supplies no universal screw-turn or RPM setting. Later series-specific service guidance still governs.
  • Caps removed to service an adjusting screw or clean the carburetor must not be reused. TI 21/2005 supplies the removal dependency; this is not authorization for permanent limiter removal.
  • Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.

Source: TI 50/2006, p. 3 · TI 50/2006, p. 4 · TI 50/2006, p. 5 — Sections 3–3.4 and summary: capped-carburetor service tool and seating stages.

Part numbers (2)
  • 5910 890 2304 — Square-bit carburetor screwdriverService tool · Carburetors using 4203 121 2700 fitted caps
  • 4203 121 2700 — Limiter capExact tool configuration · New caps; final seating after series-specific basic setting

Wrong number or missing part for the MS 260, MS 260 C? Report a correction →