Stihl 1123 · Section A · 1 of 19 · 25 parts
Engine 021
Fits 021.
Historical fitment & changes (11) — includes parts and conditions not shown on this drawing.
Parts (25)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1123 020 1219 | Cylinder with piston Ø 40 mm Fitment / change note → | 1 |
| 2 | 1123 020 1218 | Cylinder with piston Ø 40 mm Fitment / change note → | 1 |
| 4 | 1123 030 2003 | Piston Ø 40 mm Fitment / change note → | 1 |
| 5 | 1123 034 3005 | Piston ring Ø 40x1.2 mm Fitment / change note → | 2 |
| 6 | 4119 034 1500 | Piston pin 10x6.5x28 | 1 |
| 7 | 9463 650 1000 | Snap ring 10 | 2 |
| 8 | 0000 988 5211 | Connector | 1 |
| 9 | 1123 030 0411 | Crankshaft | 1 |
| 10 | 9503 003 0340 | Grooved ball bearing 6202 → replaced by 9503 003 0346 TI 6/2001 | 2 |
| 11 | 9638 003 1581 | Oil seal 15x25x5 Fitment / change note → | 2 |
| 11 | 9639 003 1585 | Oil seal 15x25x5 Fitment / change note → | 2 |
| 12 | 9468 621 1520 | Circlip 15x1 | 1 |
| 13 | 1123 021 2500 | Engine pan | 1 |
| 14 | 9075 478 4195 | Pan head self-tapping screw IS-D5.3x41 | 4 |
| 15 | 1123 020 9400 | Decompression valve Fitment / change note → | 1 |
| 16 | 1122 025 2200 | Plug Fitment / change note → | 1 |
| 17 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 17 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 30 | 1123 020 1210 | Cylinder with piston Ø 40 mm Fitment / change note → | 1 |
| 31 | 1123 020 1215 | Cylinder with piston Ø 40 mm Fitment / change note → | 1 |
| 32 | 1123 030 2019 | Piston Ø 40 mm | 1 |
| 33 | 1123 031 0500 | Crankshaft Fitment / change note → → replaced by 1123 030 0409 TI 13/1997 | 1 |
| 34 | 1123 030 1202 | Connecting rod Fitment / change note → | 1 |
| 35 | 1123 007 1005 | Set of cylindrical rollers Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0783 830 2000 | Tube of sealant Dirko HT red not illustrated | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 021 / 023 / 025
021 / 023 / 025: easy-start version and market-specific valve omission
Manual primer, decompression valve and ElastoStart are the three described components, but some early easy-start saws omitted the valve.
- The source introduces easy-start VERSIONS of 021, 023, 025, not a universal replacement of all variants. Manual fuel pump (drawing 1) primes the carburetor metering chamber; the source claims about 40% fewer pulls. This is a historical claim, not a measured guarantee or a claim of 40% less pulling force.
- Decompression valve (2) is manually opened and automatically closes after firing; ElastoStart grip (3) cushions compression peaks. A NUMBER of easy-start saws up to X 30 950 036 were supplied WITHOUT a decompression valve in SOME markets. This is a qualified omission boundary, not a universal introduction cutoff or proof that every earlier saw lacks the valve.
- Only the ElastoStart retrofit is expressly authorized across all three model families on page 5. Do not treat the parts roster or this overview as approval to retrofit the entire primer/decompression system.
- Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.
Source: TI 10/1994, p. 1 — 021 / 023 / 025: easy-start version and market-specific valve omission.
No additional parts-table entry added.
Service note · 021 / 023 / 025
021 / 023 / 025 easy start: decompression valve operation and 14 Nm torque
Manually opened valve closes after ignition; service uses a long-reach 13 mm socket.
- Complete valve 1123 020 9400 screws into cylinder. Body (1) contains axially moving tapered plunger (2); THREE spring-loaded balls (3), spaced 120 degrees, hold upper/lower positions. Push plunger DOWN to lower detent before starting: taper lifts from body, opening escape bore. During cranking some cylinder gas escapes and remaining pressure stays below closing threshold.
- Only after mixture ignites and engine runs does cylinder pressure exceed valve closing pressure, forcing plunger UP so taper closes bore. No numeric closing-pressure threshold is supplied. Drawings show mechanism, not internal service-part availability.
- Removal/installation uses standard commercial LONG-REACH 13 mm socket to ISO 2725 or DIN 3124. Tighten to 14 Nm (10.3 lbf.ft). This is valve torque, not cylinder or spark-plug torque. Some easy-start machines up to X 30 950 036 omitted the valve in some markets; do not assume presence from model alone.
- Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.
Source: TI 10/1994, p. 1 · TI 10/1994, p. 3 · TI 10/1994, p. 5 · TI 10/1994, p. 6 — 021 / 023 / 025 easy start: decompression valve operation and 14 Nm torque.
Part numbers (1)
- 1123 020 9400 — Complete decompression valve, itemAincluded in listed easy-start cylinder assemblies · 021 / 023 / 025 easy start: decompression valve operation and 14 Nm torque
Service note · 021
021: model-specific easy-start cylinder and piston
1123 020 1215 is the listed 021 easy-start assembly including decompression valveA.
- Page 6 assigns cylinder with piston 1123 020 1215 specifically to 021 EASY START, including decompression valve 1123 020 9400 (A). The separate 021/023/025 cylinder numbers are not a cross-model interchange claim. No bore, piston dimension, original cylinder replacement number or full easy-start conversion procedure is supplied.
- Page 1 qualifies valve presence: a number of easy-start saws up to X 30 950 036 lacked a valve in some markets. Preserve that statement alongside the spare-assembly inclusion; do not silently infer every originally supplied cylinder had a valve.
- Historical TI 10/1994 guidance for the named 021/023/025 variants, not MS 210/MS 230/MS 250 successors or later starting systems. Page 6 remark 1 says parts are included in other versions of 021/023; it does not independently extend that remark to 025. MOQ is a commercial order quantity, not a fitting quantity. No physical interchange test was performed.
Source: TI 10/1994, p. 1 · TI 10/1994, p. 6 — 021: model-specific easy-start cylinder and piston.
Part numbers (2)
- 1123 020 1215 — Cylinder with piston, 021 easy startmodel-specific assembly; includesA · 021: model-specific easy-start cylinder and piston
- 1123 020 9400 — Decompression valve, itemAincluded · 021: model-specific easy-start cylinder and piston
Service note · 021
021: replacement connecting rod has a press-fitted needle cage
Rod 1123 030 1202 replaces 1123 030 1204; do not infer a universal loose-cage replacement.
- 021 connecting rod 1123 030 1204 changes to 1123 030 1202, now incorporating a PRESS-FITTED needle cage for the piston pin. Original rod is no longer factory-available; introduction in progress, no serial supplied.
- The text says replacement needle cage 9512 003 2250 is consequently only required for 023 and 025. This does not prescribe fitting or removing a loose cage in the revised 021 rod, and does not establish a separate repair route for earlier 021 rods. Page 4 two-column prose must be read separately: the 025 ring change is not a connecting-rod part-number change.
- Historical TI 13/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 13/1994, p. 4 — 021: replacement connecting rod has a press-fitted needle cage.
Part numbers (2)
- 1123 030 1204 — Original 021 connecting rodno longer factory-available · 021: replacement connecting rod has a press-fitted needle cage
- 1123 030 1202 — 021 connecting rod with press-fitted cagenew · 021: replacement connecting rod has a press-fitted needle cage
Service note · 021 / 023
021 / 023: piston-ring material and assembly revisions
Section 2 applies to 021 and 023, not to 025 merely because it appears in the bulletin heading.
- Piston ring 1123 034 3000 → 1123 034 3005, made from a DIFFERENT MATERIAL; composition, coating and dimensions are not specified. Section heading explicitly limits this change to 021 / 023. No 025 application is inferred.
- Cylinder with piston 1123 020 1201 → 1123 020 1214, includes item 1 (piston). Piston D40 1123 030 2000 → 1123 030 2001, includes item 2 (ring). Ring 1123 034 3000 → 1123 034 3005. MOQ H is 1 for cylinder/piston assembly and piston, 2 for ring; MOQ is not proof of rings fitted per piston.
- All three original versions are no longer available from factory (remark 1); introduction is in progress. No production number, blanket permission to mix old/new components, or ring-end-gap specification is printed. Preserve the source’s D40 label without applying this listed piston/assembly to every displacement variant under the shared engine-sheet model labels.
- Historical TI 38/1994; modifications described as “in progress”, not a serial cutoff. Factory supply statements are historical, not current stock. No hardware operation was performed.
Source: TI 38/1994, p. 3 — 021 / 023: piston-ring material and assembly revisions.
Part numbers (6)
- 1123 020 1201 — Original cylinder with pistonhistorical listed item · 021 / 023: piston-ring material and assembly revisions
- 1123 020 1214 — New cylinder with pistonhistorical listed item · 021 / 023: piston-ring material and assembly revisions
- 1123 030 2000 — Original D40 pistonhistorical listed item · 021 / 023: piston-ring material and assembly revisions
- 1123 030 2001 — New D40 pistonhistorical listed item · 021 / 023: piston-ring material and assembly revisions
- 1123 034 3000 — Original piston ringhistorical listed item · 021 / 023: piston-ring material and assembly revisions
- 1123 034 3005 — New material piston ringhistorical listed item · 021 / 023: piston-ring material and assembly revisions
Service note · 021 / 023 / 025
021 / 023 / 025 leakage test: replace decompression valve with plug
Plug 1122 025 2200 required before testing; 13-mm deep socket for valve.
- On the named saws EQUIPPED WITH A DECOMPRESSION VALVE, plug 1122 025 2200 MUST be installed IN PLACE OF THE VALVE BEFORE THE LEAKAGE TEST. This is a test preparation step, not evidence of permanent valve deletion or an instruction to test through the valve.
- Decompression valve removal and installation use a standard commercial 13-mm DEEP WELL SOCKET. Immediately following valve-installation wording gives tightening torque 14 Nm (10 ft lbs.). Preserve that valve context; no separate plug torque is explicitly identified.
- The TI refers to the service manual for the leakage test; it does not specify test pressure, vacuum, duration, leakage limit or the complete blocking procedure. None is inferred from this note. Shared engine sheets show decompression valves but do not prove every model variant has one.
- Later shared engine sheet A key 16 lists the plug. Binding to engine sheets A/B/C provides navigation for 021/023/025; it does not extend this valve instruction to an unequipped version.
- Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 29/1995, p. 4 — Section 5.1 leakage-test service note.
Part numbers (1)
- 1122 025 2200 — Plugrequired in place of decompression valve before leakage test · 021 / 023 / 025; Section 5.1 leakage-test service note
Service note · 021 / 023 / 025
021 / 023 / 025 locking strip: close decompression valve first
Open valve may bend when piston presses against the locking strip.
- On saws EQUIPPED WITH A DECOMPRESSION VALVE, the valve MUST BE CLOSED BEFORE locking strip 0000 893 5903 is inserted into the SPARK PLUG HOLE. If left open, the valve may be bent by the piston pressing against the strip. Closed-valve prerequisite is distinct from removing the valve and fitting a plug for a leakage test.
- No piston position, turning direction, applied torque or permission to run the engine with a locking strip is supplied. This precaution is not a complete disassembly procedure or proof that the strip is suitable for every other saw model.
- Footer: August 7, 1995, D1/MTK-st; prior TI 17/1995 is bibliographic. It is not a serial cutoff or production date for these in-progress changes. No hardware procedure has been performed.
- Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 29/1995, p. 4 — Section 5.2 locking-strip precaution and footer.
Part numbers (1)
- 0000 893 5903 — Locking stripinsert only after closing decompression valve · 021 / 023 / 025; Section 5.2 locking-strip precaution and footer
Service note · 021 / 023 / 025
021/023/025: oil seal depends on engine-pan separation
Assembled cylinder and pan permit press-fitting only 9638 003 1581.
- Section 3: IF THE ENGINE PAN IS SEPARATED from the cylinder during repair, production oil seal 9639 003 1585 WITH RIGID HOUSING MAY be installed. This is conditional permission, not an instruction that it must replace every 1581 seal.
- IF CYLINDER AND ENGINE PAN ARE STILL ASSEMBLED, ONLY oil seal 9638 003 1581 (the replacement supplied up to then) MAY BE PRESS-FITTED. Equal dimensions or coexistence in an IPL do not make 1585 a press-in replacement in this assembled condition.
- The summary table prints original --- and new 9638 003 1581 even though the prose calls 1581 the previously supplied replacement. Preserve both statements: the table does not establish a 1581→1585 supersession or cancel the assembly-state restriction.
- The detailed technical reasons are explicitly deferred to TI39/1990. That source is unavailable in the retained 690-TI corpus and bounded service-documentation PDF filename inventory (766 PDFs); no mechanical rationale, insertion tool, depth, sealant or torque is invented.
- Later engine sheets A (021), B (023/023 L) and C (025) list BOTH seal numbers as 15x25x5, quantity 2, under their shared seal key. Those are IPL dimensions/quantities, not additional specifications printed in this TI and not unrestricted interchange.
- Historical TI24/1996 guidance only. No serial cutoff is stated; introduction is in progress, not a verified calendar date. Shared IPL sheets do not extend applicability to other variants or MS successor models. Supply statements are historical, not present stock guarantees. No hardware operation was performed.
Source: TI 24/1996, p. 1 · TI 24/1996, p. 3 — 021/023/025: oil seal depends on engine-pan separation.
Part numbers (2)
- 9639 003 1585 — Oil seal with rigid housingPermitted when pan is separated · 021/023/025; installation depends on pan/cylinder assembly state
- 9638 003 1581 — Oil seal, existing replacementOnly press-fit seal while pan/cylinder remain assembled · 021/023/025; installation depends on pan/cylinder assembly state
Service note · 021
021: composite crankshaft and retained old rod/rollers
The new crankshaft and connecting rod are inseparable; old service parts remain available.
X 34 944 403 — 021 crank drive modification only; not the independent 025 carburetor cutoff.
- From machine number X 34 944 403, original one-piece crankshaft 1123 031 0500 is replaced by multi-part crankshaft 1123 030 0409. The composite design is pressed together into a torsionally rigid unit. The small-end needle sleeve is press-fitted into the connecting rod. The original illustration labels the old crankshaft LEFT and new crankshaft RIGHT.
- The connecting rod and NEW crankshaft are INSEPARABLE. Connecting rod 1123 030 1202 and cylindrical-roller set 1123 007 1005 cease production-line use but REMAIN spare parts for the old design. Their new-part columns are dashes, not replacement part numbers or permission to dismantle the new pressed assembly. The original crankshaft also remains available for older machines.
- New crankshaft 1123 030 0409 MUST be used with piston 1123 030 2003. The piston pairing and separate 023/025 needle-cage statement are retained in companion notes; this 021 cutoff must not be generalized to 023 or 025.
- Historical TI13/1997 evidence for the exact named model/configuration only. Shared IPL labels are discovery links, not applicability to every model or later carburetor suffix on that sheet. Availability statements describe 1997, not current stock. No successor-model scope, universal retrofit or tested interchange is inferred. No hardware operation was performed.
Source: TI 13/1997, p. 1 · TI 13/1997, p. 2 — 021: composite crankshaft and retained old rod/rollers.
Part numbers (4)
- 1123 031 0500 — Original one-piece crankshaftRetained for older machines · 021; 021: composite crankshaft and retained old rod/rollers
- 1123 030 0409 — New multi-part crankshaftNew; inseparable connecting rod · 021; 021: composite crankshaft and retained old rod/rollers
- 1123 030 1202 — Original connecting rodSpare retained; no new separate rod · 021; 021: composite crankshaft and retained old rod/rollers
- 1123 007 1005 — Original set of cylindrical rollersSpare retained; no new separate set · 021; 021: composite crankshaft and retained old rod/rollers
Service note · 021
021: mandatory piston pairing and 12.7 / 12.2 mm dimension
The original scan labels the dimension a; OCR incorrectly renders D.
X 34 944 403 — 021 crank drive modification only; not the independent 025 carburetor cutoff.
- Piston 1123 030 2003 MUST be used with new crankshaft 1123 030 0409. Original piston 1123 030 2001 remains available for machines with old crankshaft 1123 031 0500. The table identifies item 5 as a 40 mm diameter piston; the separate 12.7 / 12.2 mm dimension is NOT the piston bore.
- The ORIGINAL page 1 drawing and caption label the compared dimension lowercase a: a = 12.7 mm for original piston 1123 030 2001; a = 12.2 mm for new piston 1123 030 2003. The retained text extraction says D instead. The scan controls this label; the text artifact is not silently rewritten. The drawing shows the dimension across the central opening; no unprinted tolerance, machining instruction or alternate dimension name is supplied.
- The source repeats that original piston 1123 030 2001 MUST STILL be installed in model 023 saws. Do not apply the 021 piston change to 023, or assume shared 40 mm diameter establishes interchange. The 021 change starts at X 34 944 403.
- Historical TI13/1997 evidence for the exact named model/configuration only. Shared IPL labels are discovery links, not applicability to every model or later carburetor suffix on that sheet. Availability statements describe 1997, not current stock. No successor-model scope, universal retrofit or tested interchange is inferred. No hardware operation was performed.
Source: TI 13/1997, p. 1 · TI 13/1997, p. 2 — 021: mandatory piston pairing and 12.7 / 12.2 mm dimension.
Part numbers (4)
- 1123 030 2001 — Original piston, 40 mm; a = 12.7 mmRetained old-crankshaft piston; still required on 023 · 021; 021: mandatory piston pairing and 12.7 / 12.2 mm dimension
- 1123 030 2003 — New piston, 40 mm; a = 12.2 mmRequired with new 021 crankshaft · 021; 021: mandatory piston pairing and 12.7 / 12.2 mm dimension
- 1123 030 0409 — New 021 crankshaftRequires piston 2003 · 021; 021: mandatory piston pairing and 12.7 / 12.2 mm dimension
- 1123 031 0500 — Original 021 crankshaftUses retained piston 2001 · 021; 021: mandatory piston pairing and 12.7 / 12.2 mm dimension
Service note · 021
021: separate standard and California cylinder/piston sets
Both assemblies include item 5; originals remain available for older machines.
X 34 944 403 — 021 crank drive modification only; not the independent 025 carburetor cutoff.
- At X 34 944 403, table item 4 cylinder with piston changes from 1123 020 1215 to 1123 020 1218. Item 6 cylinder with piston (CALIFORNIA) changes separately from 1123 020 1210 to 1123 020 1219. Do not exchange market labels or combine these rows.
- BOTH assembly rows explicitly include item 5: old piston 1123 030 2001 or new piston 1123 030 2003, as appropriate to the version. Item 5 is 40 mm diameter. Remark 1 keeps ALL original versions available for older machines. No standalone cylinder number, other included parts, universal retrofit or cylinder-only geometry change is stated.
- The mandatory new crankshaft/piston pairing still applies, and original piston 2001 remains required on 023. The California crank-drive cutoff X 34 944 403 is NOT the independent 025 California carburetor cutoff X 34 191 135.
- Historical TI13/1997 evidence for the exact named model/configuration only. Shared IPL labels are discovery links, not applicability to every model or later carburetor suffix on that sheet. Availability statements describe 1997, not current stock. No successor-model scope, universal retrofit or tested interchange is inferred. No hardware operation was performed.
Source: TI 13/1997, p. 1 · TI 13/1997, p. 2 — 021: separate standard and California cylinder/piston sets.
Part numbers (6)
- 1123 020 1215 — Original standard cylinder with piston, item 4Retained old version · 021; 021: separate standard and California cylinder/piston sets
- 1123 020 1218 — New standard cylinder with piston, item 4New version · 021; 021: separate standard and California cylinder/piston sets
- 1123 020 1210 — Original California cylinder with piston, item 6Retained old version · 021; 021: separate standard and California cylinder/piston sets
- 1123 020 1219 — New California cylinder with piston, item 6New version · 021; 021: separate standard and California cylinder/piston sets
- 1123 030 2001 — Original included piston, item 5Old set component · 021; 021: separate standard and California cylinder/piston sets
- 1123 030 2003 — New included piston, item 5New set component · 021; 021: separate standard and California cylinder/piston sets
Wrong number or missing part for the 021? Report a correction →