Stihl 1124 · Section B · 2 of 15 · 26 parts
Cylinder, Muffler
Fits 084.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (26)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1124 029 2300 | Cylinder gasket | 1 |
| 2 | 9512 003 3440 | Needle cage 13 x17x17.5 | 1 |
| 3 | 1124 020 1203 | Cylinder with piston Ø 60 mm Fitment / change note → | 1 |
| 4 | 1124 030 2007 | Piston Ø 60 mm Fitment / change note → | 1 |
| 5 | 1124 034 3010 | Piston ring Ø 60x1.2 mm | 2 |
| 6 | 1124 034 1500 | Piston pin 13x8x39 | 1 |
| 7 | 9463 650 1300 | Snap ring 13x1 | 2 |
| 8 | 1124 020 9400 | Decompression valve | 1 |
| 9 | 9636 003 0420 | Sealing ring 6.5x9.5 | 1 |
| 10 | 1124 025 3300 | Grommet | 1 |
| 11 | 9022 341 0910 | Spline screw IS-M5x6 | 1 |
| 12 | 9022 341 1350 | Spline screw IS-M6x25 | 4 |
| 13 | 1124 149 0600 | Muffler gasket | 1 |
| 14 | 1124 140 0605 | Muffler | 1 |
| 15 | 1117 141 9000 | Screen | 1 |
| 16 | 1124 145 0805 | Exhaust casing | 1 |
| 17 | 1124 140 0600 | Muffler | 1 |
| 18 | 1124 145 0800 | Exhaust casing | 1 |
| 19 | 9022 341 1010 | Spline screw IS-M5x18 | 2 |
| 20 | 9022 341 0910 | Spline screw IS-M5x6 | 2 |
| 21 | 9022 341 1310 | Spline screw IS-M6x18 | 2 |
| 22 | 9022 341 1010 | Spline screw IS-M5x18 | 2 |
| 23 | 9307 021 0120 | Washer 5.3 | 4 |
| 24 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 24 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1124 007 1050 | Set of gaskets 084 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 084
084 replacement piston: reinforced boss and six-cross identification
Piston 2007 replaces 2005 while the cylinder-with-piston assembly number stays unchanged.
- Section 1 is 084 ONLY: piston 1124 030 2007 will be supplied instead of 1124 030 2005. Its piston-pin boss is reinforced and its lubricating recesses optimized. Six crosses identify the new piston; the original detail shows TWO COLUMNS OF THREE crosses. The drawing does not supply manufacturing dimensions, tolerances or a machining instruction.
- Cylinder with piston 1124 020 1203 retains the SAME NUMBER before and after, and explicitly includes item 2, the piston. Therefore that assembly number alone does not identify the included piston revision. ALL OTHER PARTS AS BEFORE is retained; no replacement cylinder number is invented.
- Introduction is IN PROGRESS, without a date or machine cutoff. Remark 1 says original piston 1124 030 2005 is no longer available from the factory. This is not the clutch old-assembly retention rule. The new piston was already installed in 088 from the start of production; that context does not make this a new 088 piston change.
- Historical TI17/1997 evidence for the named model and section only. No serial cutoff is supplied. Factory availability describes the bulletin date, not present stock. No MS880/MS881 scope, reciprocal component interchange or physical verification inferred. No hardware operation was performed.
Source: TI 17/1997, p. 1 — 084 replacement piston: reinforced boss and six-cross identification.
Part numbers (3)
- 1124 030 2005 — Original 084 pistonNo longer available from factory · 084; 084 replacement piston: reinforced boss and six-cross identification
- 1124 030 2007 — Replacement piston with six crossesReinforced boss and optimized lubricating recesses · 084; 084 replacement piston: reinforced boss and six-cross identification
- 1124 020 1203 — Cylinder with piston, including item 2Unchanged assembly number; included piston changes · 084; 084 replacement piston: reinforced boss and six-cross identification
Wrong number or missing part for the 084? Report a correction →